ENGINES 112.910, 112.911 up to May 31, 2000, 112.920, 112.921 up to May 31, 2000, 112.923, 112.940 /941 /942 up to May 31, 2000, 112.943
ENGINE PERFORMANCE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Possible cause | Diagnostic |
|---|---|---|
| No fault code | No fault detected Depending on the complaint, carry out testing of ME-SFI electrical system in full 112.942 in MODEL 163.154 up to 31.5.98 |
ME-SFI gasoline injection system - Testing electrical system |
| ME-SFI ignition system - Testing electrical system | ||
| ME-SFI idle speed control/electronic accelerator - Testing electrical system | ||
| ME-SFI cruise control with variable speed limiting - Testing electrical system | ||
| ME-SFI cruise control without variable speed limiting - Testing electrical system | ||
| P0100 | Hot-film mass air flow sensor (B2/5) | Testing of electrical system for ME-SFI fuel injection system hot film air mass sensor |
| Hot film mass air flow sensor, fault code description ME-SFI | Hot film MAF sensor, fault code description, ME-SFI | |
| P0105 | Pressure sensor (B28) | Pressure sensor - Testing electrical system, ME-SFI gasoline injection system |
| Pressure sensor, fault code description ME-SFI | Fault code description - ME-SFI - pressure sensor | |
| P0110 | Intake air temperature sensor (in the hot film mass air flow sensor B2/5) | Intake air temperature sensor - ME-SFI gasoline injection system - Testing electrical system |
| Intake air temperature sensor, fault code description ME-SFI | Fault code description - ME-SFI - intake air temperature sensor | |
| P0115 | Coolant temperature sensor (B11/4) | Coolant temperature sensor - ME-SFI gasoline injection system - Testing electrical system |
| Coolant temperature sensor, fault code description ME-SFI | Fault code description - ME-SFI - coolant temperature sensor | |
| P0120 | Actual value potentiometer in the throttle valve actuator (M16/6) | Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics |
| Actual value potentiometer in the throttle valve actuator, fault code description ME-SFI | ME-SFI actual value potentiometer in the throttle valve actuator, fault code description | |
| P0130 | A Oxygen sensor on right upstream of TWC (G3/4) | AD07.61-P-6000-11A |
| B Oxygen sensor on right upstream of TWC (G3/4) voltage increase too small | ||
| Oxygen sensor signal, fault code description ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0133 | A Oxygen sensor on right upstream of TWC (G3/4) aging correction variable exceeded | AD07.61-P-6000-11A |
| B Oxygen sensor on right upstream of TWC (G3/4) aging of cycle duration too long | ||
| C Oxygen sensor on right upstream of TWC (G3/4) aging of Oxygen sensor too slow | ||
| Aging of oxygen sensor upstream of TWC, fault code description ME-SFI | O2 Fault code description - ME-SFI - ageing of oxygen sensor upstream of TWC | |
| P035 | Oxygen sensor heating of O sensor on right upstream of TWC (G3/4) | AD07.61-P-6000-13A |
| Oxygen sensor heating, fault code description ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0136 | Oxygen sensor on right downstream of TWC (G3/6) with CODE (925) low-emission EURO3 |
Oxygen sensor signal on right downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Oxygen sensor signal, fault code description ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0140 | Oxygen sensor on right upstream of TWC (G3/4) | AD07.61-P-6000-11A |
| Oxygen sensor signal, fault code description ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0141 | Oxygen sensor heating of Oxygen sensor on right downstream of TWC (G3/6) with CODE (925) low-emission EURO3 |
Oxygen sensor heating on right downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Oxygen sensor heating, fault code description ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0150 | A Oxygen sensor on left upstream of TWC (G3/3) | AD07.61-P-6000-10A |
| B Oxygen sensor on left upstream of TWC (G3/3) voltage increase too small | ||
| Oxygen sensor signal, fault code description ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0153 | A Oxygen sensor on left upstream of TWC (G3/3) aging of correction variable exceeded | AD07.61-P-6000-10A |
| B Oxygen sensor on left upstream of TWC (G3/3) aging of cycle duration too long | ||
| C Oxygen sensor on left upstream of TWC (G3/3) aging of Oxygen sensor too slow | ||
| Aging of oxygen sensor upstream of TWC, fault code description ME-SFI | O2 Fault code description - ME-SFI - ageing of oxygen sensor upstream of TWC | |
| P0155 | Oxygen sensor heating of Oxygen sensor on left upstream of TWC (G3/3) | AD07.61-P-6000-12A |
| Oxygen sensor heating, fault code description ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0156 | Oxygen sensor on left downstream of TWC (G3/5) with CODE (925) low-emission EURO3 |
Oxygen sensor signal on left downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Oxygen sensor signal, fault code description ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0160 | Oxygen sensor on left downstream of TWC (G3/5) with CODE (925) low-emission EURO3 |
Oxygen sensor signal on left downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Oxygen sensor signal, fault code description ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0161 | Oxygen sensor heating of Oxygen sensor on left downstream of TWC (G3/5) with CODE (925) low-emission EURO3 |
Oxygen sensor heating on left downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Oxygen sensor heating, fault code description ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0170 | A Self-adaptation of the "partial load" mixture formation for right cylinder bank to limit value of ME-SFI control module (N3/10) | Air leak, fuel injectors of diaphragm-type pressure regulating valve, wear to engine |
| A Self-adaptation of the "idle" mixture formation for right cylinder bank to limit value of ME-SFI control module (N3/10) | ||
| Self-adaptation of mixture formation to limit, fault code description ME-SFI | Self-adaptation of mixture formation to limit, fault code description ME-SFI | |
| P0173 | A Self-adaptation of the "partial load" mixture formation for left cylinder bank to limit value of ME-SFI control module (N3/10) | Air leak, fuel injectors of diaphragm-type pressure regulating valve, wear to engine |
| B Self-adaptation of the "idle" mixture formation for left cylinder bank to limit value of ME-SFI control module (N3/10) | ||
| Self-adaptation of mixture formation to limit, fault code description ME-SFI | Self-adaptation of mixture formation to limit, fault code description ME-SFI | |
| P0201 | Fuel injector (Y62y1) cylinder 1 | Fuel injector (Y62/1) - ME-SFI gasoline injection system - Testing electrical system |
| Fuel injectors, fault code description ME-SFI | ME-SFI fault code description for fuel injectors | |
| P0202 | Fuel injector (Y62y2) cylinder 2 | Testing of electrical system for ME-SFI fuel injection system, fuel injector (Y62/2) |
| Fuel injectors, fault code description ME-SFI | ME-SFI fault code description for fuel injectors | |
| P0203 | Fuel injector (Y62y3) cylinder 3 | Testing of electrical system for ME-SFI fuel injection system, fuel injector (Y62/3) |
| Fuel injectors, fault code description ME-SFI | ME-SFI fault code description for fuel injectors | |
| P0204 | Fuel injector (Y62y4) cylinder 4 | Testing of electrical system for ME-SFI fuel injection system, fuel injector (Y62/4) |
| Fuel injectors, fault code description ME-SFI | ME-SFI fault code description for fuel injectors | |
| P0205 | Fuel injector (Y62y5) cylinder 5 | Testing of electrical system for ME-SFI fuel injection system, fuel injector (Y62/5) |
| Fuel injectors, fault code description ME-SFI | ME-SFI fault code description for fuel injectors | |
| P0206 | Fuel injector (Y62y6) cylinder 6 | Testing of electrical system for ME-SFI fuel injection system, fuel injector (Y62/6) |
| Fuel injectors, fault code description ME-SFI | ME-SFI fault code description for fuel injectors | |
| P0300 | A Misfire | Primary voltage (T1/1) - ME-SFI ignition system - Testing electrics |
| B Misfire "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, primary voltage (T1/2) | |
| Testing of electrical system for ME-SFI ignition system, primary voltage (T1/3) | ||
| Testing of electrical system for ME-SFI ignition system, primary voltage (T1/4) | ||
| Testing of electrical system for ME-SFI ignition system, primary voltage (T1/5) | ||
| Testing of electrical system for ME-SFI ignition system, primary voltage (T1/6) | ||
| Testing of electrical system for ME-SFI ignition system, ignition voltage | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Fault code description for misfires, ME-SFI | ME-SFI fault code description, misfire | |
| P0301 | A Misfire in cylinder 1 | Primary voltage (T1/1) - ME-SFI ignition system - Testing electrics |
| B Misfire in cylinder 1 "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, ignition voltage | |
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0302 | A Misfire in cylinder 2 | Testing of electrical system for ME-SFI ignition system, primary voltage (T1/2) |
| B Misfire in cylinder 2 "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, ignition voltage | |
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0303 | A Misfire in cylinder 3 | Testing of electrical system for ME-SFI ignition system, primary voltage (T1/3) |
| B Misfire in cylinder 3 "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, ignition voltage | |
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0304 | A Misfire in cylinder 4 | Testing of electrical system for ME-SFI ignition system, primary voltage (T1/4) |
| B Misfire in cylinder 4 "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, ignition voltage | |
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0305 | A Misfire in cylinder 5 | Testing of electrical system for ME-SFI ignition system, primary voltage (T1/5) |
| B Misfire in cylinder 5 "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, ignition voltage | |
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0306 | A Misfire in cylinder 6 | Testing of electrical system for ME-SFI ignition system, primary voltage (T1/6) |
| B Misfire in cylinder 6 "damaging to TWC" | Testing of electrical system for ME-SFI ignition system, ignition voltage | |
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors | ||
| Compression pressure | ||
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0325 | Knock sensor on right | Connector line |
| Knock sensor | ||
| Knock sensor, fault code description ME-SFI | Fault code description - ME-SFI - knock sensor | |
| P0330 | Knock sensor on left | Connector line |
| Knock sensor | ||
| Knock sensor, fault code description ME-SFI | Fault code description - ME-SFI - knock sensor | |
| P0335 | Crankshaft position sensor (L5) | Testing of electrical system for ME-SFI ignition system crankshaft position sensor |
| Crankshaft position sensor, fault code description ME-SFI | Fault code description - ME-SFI - crankshaft position sensor | |
| P0341 | Camshaft Hall sensor (B6/1) | Testing of electrical system for ME-SFI ignition system, camshaft Hall sensor |
| Camshaft Hall sensor, fault code description ME-SFI | Fault code description - ME-SFI - camshaft Hall sensor | |
| P0370 | Angle deviation for camshaft to crankshaft | Check basic adjustment of camshafts |
| P0400 | Exhaust gas recirculation malfunction (causal chain) | Testing of electrical system for ME-SFI fuel injection system ERG vacuum transducer |
| Exhaust gas recirculation malfunction (causal chain), fault code description ME-SFI | Exhaust gas recirculation malfunction (causal chain), fault code description ME-SFI | |
| P0410 | Secondary air injection malfunction (causal chain) with CODE (925) low-emission EURO3 |
Secondary air injection relay - Testing electrical system, ME-SFI gasoline injection system |
| Air pump switchover valve - Testing electrical system, ME-SFI gasoline injection system | ||
| Secondary air injection - Testing electrical system, ME-SFI gasoline injection system | ||
| Secondary air injection malfunction (causal chain), fault code description ME-SFI | ME-SFI secondary air injection malfunction (causal chain) - Fault code description | |
| P0422 | Effect of right three-way catalytic converter too low | Right three-way catalytic converter |
| Three-way catalytic converter effect too low, fault code description ME-SFI | Fault code description - three-way catalytic converter effect too low | |
| P0432 | Effect of left three-way catalytic converter too low | Left three-way catalytic converter |
| Three-way catalytic converter effect too low, fault code description ME-SFI | Fault code description - three-way catalytic converter effect too low | |
| P0440 | Purge system leak (causal chain) | Purge control valve vacuum control - ME-SFI gasoline injection system - Testing electrical system |
| Purge system - Testing electrical system, ME-SFI gasoline injection system | ||
| Purge system leak (causal chain), fault code description ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0441 | Purge control valve (Y58/1) Function | Purge control valve activation - ME-SFI gasoline injection system - Testing electrical system |
| Purge control valve vacuum control - ME-SFI gasoline injection system - Testing electrical system | ||
| Purge system leak (causal chain), fault code description ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0442 | Purge system slight leak | Purge system - Testing electrical system, ME-SFI gasoline injection system |
| Purge system leak (causal chain), fault code description ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0443 | Purge control valve (Y58/1) | Purge control valve activation - ME-SFI gasoline injection system - Testing electrical system |
| Purge control valve, fault code description ME-SFI | Fault code description - ME-SFI - purge control valve | |
| P0446 | A Activated charcoal canister shutoff valve (causal chain) | Activated charcoal canister shutoff valve - Testing electrical system, ME-SFI gasoline injection system |
| B Shutoff valve for activated charcoal canister (Y58/4) | Tank pressure sensor - Testing electrical system, ME-SFI gasoline injection system | |
| Activated charcoal canister shutoff valve, fault code description ME-SFI | Fault code description for activated charcoal canister shutoff valve, ME-SFI | |
| P0450 | A Tank pressure sensor (B4/3) electrical fault B Tank pressure sensor (B4/3), signal oscillates |
Tank pressure sensor - Testing electrical system, ME-SFI gasoline injection system Activated charcoal canister blocked |
| Tank pressure sensor, fault code description ME-SFI | Fault code description for tank pressure sensor, ME-SFI | |
| P0455 | Purge system with severe leak or voltage supply for tank pressure sensor (B4/3) | Purge system - Testing electrical system, ME-SFI gasoline injection system Tank pressure sensor - Testing electrical system, ME-SFI gasoline injection system |
| Purge system leak (causal chain), fault code description ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0460 | Fuel level gage sensor | Read out terminal |
| Misfires, fault code description ME-SFI | ME-SFI fault code description, misfire | |
| P0500 | A front left vehicle speed signal B rear left vehicle speed signal |
Check ASR in chassis diagnosis manual, index 9 AD42.45-P-1000AZ |
| Vehicle speed signal, fault code description ME-SFI | Fault code description - ME-SFI - vehicle speed signal | |
| P0507 | Idle speed control implausible Signal 1 |
Pedal value sensor signal - Testing electrical system, ME-SFI idle speed control/electronic accelerator |
| Signal 2 | Pedal value sensor signal - Testing electrical system, ME-SFI idle speed control/electronic accelerator | |
| Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics | ||
| Idle speed control, fault code description ME-SFI | Fault code description - ME-SFI - idle speed control | |
| P0560 | Voltage supply to ME-SFI control module (N3/10) | Testing of electrical system for ME-SFI control module terminal 30 in ME-SFI fuel injection system Testing of electrical system for ME-SFI control module terminal 87 in ME-SFI fuel injection system |
| Control module voltage supply, fault code description ME-SFI | ME-SFI control module voltage supply - Fault code description | |
| P0565 | Pushbutton switch for variable cruise control (S40/4) | Cruise control pushbutton switch - Testing electrical system, ME-SFI cruise control with variable speed limiting |
| P0600 | CAN of ESP | CAN data bus - ME-SFI gasoline injection system - Testing electrical system |
| CAN damaged, fault code description ME-SFI | Fault code description - ME-SFI - CAN faulty | |
| P0604 | A ME-SFI control module (N3/10) B ME-SFI control module (N3/10) |
N3/10 |
| P0605 | ME-SFI control module (N3/10) | N3/10 |
| P0700 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ME-SFI gasoline injection system - Testing electrical system |
| ME-SFI ignition system - Testing electrical system | ||
| ME-SFI idle speed control/electronic accelerator - Testing electrical system | ||
| ME-SFI cruise control with variable speed limiting - Testing electrical system | ||
| Gear implausible or transmission with leaks, fault code description ME-SFI | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM | |
| Fault code description - ME-SFI - gear implausible or transmission with leaks | ||
| Command valve sticks in pressure position, fault code description ME-SFI | Fault code description - ME-SFI - command valve sticks in pressure position | |
| P0702 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| ETC control module, fault code description ME-SFI | Fault code description - ME-SFI - ETC control module | |
| Valve supply voltage, fault code description ME-SFI | Fault code description - ME-SFI - valve supply voltage | |
| P0715 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Supply voltage and function of RPM sensors, fault code description ME-SFI | Fault code description - ME-SFI - supply voltage and function of RPM sensors | |
| P0720 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for CAN fault identification, ME-SFI | Fault code description - ME-SFI - CAN fault identification | |
| P0730 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Gear comparison (multiple times) negative, fault code description ME-SFI | Fault code description - ME-SFI - gear comparison (multiple times) negative | |
| P0740 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Torque converter lockup clutch, fault code description ME-SFI | Fault code description - ME-SFI - torque converter lockup clutch | |
| P0743 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| PWM-solenoid of torque converter lockup, fault code description ME-SFI | Fault code description - ME-SFI - PWM-solenoid of torque converter lockup | |
| P0748 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Modulating pressure control solenoid, fault code description ME-SFI | Fault code description - ME-SFI - modulating pressure control solenoid | |
| Switching pressure control solenoid, fault code description ME-SFI | ME-SFI shifting pressure control solenoid valve - Fault code description | |
| P0753 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| 1 - 2/4 - 5 shift solenoid, fault code description ME-SFI | ME-SFI 1-2/4-5 shifting solenoid valve - Fault code description | |
| P0758 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| 2 - 3 shift solenoid, fault code description ME-SFI | ME-SFI 2-3 shifting solenoid valve - Fault code description | |
| P0763 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| 3 - 4 shift solenoid, fault code description ME-SFI | ME-SFI 3-4 shifting solenoid valve - Fault code description | |
| P0801 | Electric suction-type fan for engine/AC (M4/3) | Suction-type fan control module - Testing electrical system, ME-SFI gasoline injection system |
| P0802 | Variable intake manifold switchover valve (Y22/6) | Resonance intake manifold switchover valve - Testing electrical system, ME-SFI gasoline injection system |
| P0809 | Angle deviation for camshaft to crankshaft | Check basic adjustment of camshafts |
| P0811 | CAN of EIS | CAN data bus - ME-SFI gasoline injection system - Testing electrical system |
| P1031 | Oxygen sensors upstream of TWC (G3/3 and G3/4) exchanged | Check connectors |
| P1177 | Oil sensor (oil level/temperature/quality) (B40): oil temperature implausible | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1178 | Oil sensor (oil level/temperature/quality) (B40): oil level implausible | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1179 | Oil sensor (oil level/temperature/quality) (B40): oil quality implausible | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1180 | Oil sensor (oil level/temperature/quality) (B40): oil temperature too high | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1181 | Electric suction-type fan for engine/AC (M4/3) | Suction-type fan control module - Testing electrical system, ME-SFI gasoline injection system |
| P1185 | Oil sensor (oil level/temperature/quality) (B40): water in oil | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1186 | Safety fuel shutoff detected | Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics Throttle valve actuator actuation - ME-SFI idle speed control/electronic accelerator - Testing electrics Throttle valve actuator sluggish/sticks Check intake train for residue |
| P1225 | Variable intake manifold switchover valve (Y22/6) | Resonance intake manifold switchover valve - Testing electrical system, ME-SFI gasoline injection system |
| P1233 | Throttle valve actuator (M16/6) sticks (iced up) | Actuator |
| P1386 | Anti-knock control by the ME-SFI control module (N3/10) at the control stop | Increased tendency to knock due to poor fuel, coked combustion chambers or mechanical damage ME-SFI control module (N3/10) |
| Anti-knock control in the ME-SFI control module for computer error, fault code description ME-SFI | ME-SFI anti-knock control in the control module, hardware fault, fault code description | |
| P1400 | EGR transducer (Y31/1) | Testing of electrical system for ME-SFI fuel injection system ERG vacuum transducer |
| EGR transducer, fault code description ME-SFI | ME-SFI EGR transducer - Fault code description | |
| P1420 | Air pump switchover valve (Y32) with CODE (925) low-emission EURO3 |
Air pump switchover valve - Testing electrical system, ME-SFI gasoline injection system |
| Secondary-air injection, fault code description ME-SFI | ME-SFI secondary air injection - Fault code description | |
| P1453 | Air pump relay with CODE (925) low-emission EURO3 |
Secondary air injection relay - Testing electrical system, ME-SFI gasoline injection system |
| Secondary-air injection, fault code description ME-SFI | ME-SFI secondary air injection - Fault code description | |
| P1491 | Refrigerant pressure in the air conditioning too high | Check air conditioning |
| P1542 | Pedal value sensor (B37) Signal 1 | Pedal value sensor signal - Testing electrical system, ME-SFI idle speed control/electronic accelerator |
| Signal 2 | Pedal value sensor signal - Testing electrical system, ME-SFI idle speed control/electronic accelerator | |
| Pedal value sensor, fault code description ME-SFI | ME-SFI pedal value sensor - Fault code description | |
| P1570 | Start authorization from DAS not granted | Incorrect operation |
| A Start attempted with locked DAS | AD80.35-P-1000AZ | |
| B CAN from DAS control module to ME-SFI control module (N3/10) damaged | AD80.35-P-1000BZ CAN data bus - ME-SFI gasoline injection system - Testing electrical system Check control modules and part no. |
|
| C ME-SFI control module and DAS control module do not match | ||
| P1580 | Throttle valve actuator (M16/6) | Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics Throttle valve actuator actuation - ME-SFI idle speed control/electronic accelerator - Testing electrics |
| Throttle valve actuator, fault code description ME-SFI | ME-SFI throttle valve actuator - Fault code description | |
| P1584 | Stop lamp switch | Check ASR in chassis diagnosis manual, index 9 |
| AD42.45-P-1000AZ | ||
| P1603 | CAN of EIS | CAN data bus - ME-SFI gasoline injection system - Testing electrical system |
| P1605 | Signal for poor road detection (through comparison of wheel speeds) | Check ASR in chassis diagnosis manual, index 9 |
| AD42.45-P-1000AZ | ||
| P1642 | ME-SFI control module coded incorrectly (coded to MT, vehicle has AT) | Notes on ME-SFI diagnostic trouble code memory |
| P1643 | ME-SFI control module coded incorrectly (coded to AT, vehicle has MT) or no CAN transfer from the automatic transmission control module (N15/3) |
Notes on ME-SFI diagnostic trouble code memory ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| P1644 | Transmission version cannot be checked due to undervoltage at the ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| P1681 | Crash signal implausible as of 06/98 |
Crash signal - Testing ME-SFI electrical system |
| P1747 | A CAN fault: transmission protection malfunction from the ETC control module (N15/3) B CAN fault: instrument cluster |
ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM Check terminal, communication diagnosis manual, index 1 |
| CAN damaged, fault code description ME-SFI | Fault code description - ME-SFI - CAN faulty | |
|
Fault code STAR DIAGNOSIS (Display on generic scan tool) |
ENGINE 112.910 /911 /920 /921 /922 /940 /941 /942 /944 as of 1.6.00 ENGINE 112.912 /913 /914 /916 /917 /923 /943 /946 /947 /949 /953 /954 /955 /970 /972 /973 /975 |
|
| P2001 (P0400) | Exhaust gas recirculation malfunction (function chain), ME-SFI fault code description | Exhaust gas recirculation malfunction (function chain), ME-SFI fault code description |
| P2003 (P0410) | Air injection malfunction (function chain), ME-SFI fault code description | ME secondary air injection malfunction (causal chain) - fault code description |
| P2004 (P0100) | Hot-film MAF sensor, ME-SFI fault code description | Hot-film mass-air sensor ME-SFI - fault code description |
| P2005 (P0115) | Coolant temperature sensor, ME-SFI fault code description | Coolant temperature sensor ME-SFI - fault code description |
| P2006 (P0110) | Intake air temperature sensor, ME-SFI fault code description | Intake air temperature sensor ME-SFI - fault code description |
| P2007 (P0105) | Pressure sensor, ME-SFI fault code description | Pressure sensor ME-SFI - fault code description |
| P2008 (P0135) | O2S-sensor heater, ME-SFI fault code description. Right O2 sensor upstream TWC [KAT], internal resistor. | O2-sensor heating - fault code description ME-SFI |
| P2009 (P0141) | O2S-sensor heater, ME-SFI fault code description. Right O2 sensor downstream TWC [KAT], internal resistor | O2-sensor heating - fault code description ME-SFI |
| P200A (-) | Anti-knock control in hardware fault control unit, ME-SFI fault code description | Anti-knock control in the hardware fault control unit, ME-SFI fault code description |
| P200B (P0422) | Fault code description - Right catalytic converter efficiency too low | Fault code description - three-way catalytic converter effectiveness too low |
| P200C (-) | Aging of O2 sensor downstream TWC, ME-SFI fault code description. Right O2 sensor downstream TWC [KAT], correction variable exceeded | Aging of O2 sensor upstream of TWC - fault code description ME |
| P200D (P0133) | Aging of O2 sensor downstream TWC, ME-SFI fault code description. Right O2 sensor upstream TWC [KAT], period duration | Aging of O2 sensor upstream of TWC - fault code description ME |
| P200E (-) | O2 Sensor signal, ME-SFI fault code description. Right O2 sensor downstream TWC [KAT], no sensor status change | O2 sensor signal - fault code description ME |
| P200F (P0130) | O2 Sensor signal, ME-SFI fault code description. Right O2 sensor upstream TWC [KAT], electrical fault | O2 sensor signal - fault code description ME |
| P2010 (P0136) | O2 Sensor signal, ME-SFI fault code description. Right O2 sensor downstream TWC [KAT], electrical fault | O2 sensor signal - fault code description ME |
| P2011 (-) | Knock sensor, ME-SFI fault code description. Right knock sensor 1 | Knock sensor ME - fault code description |
| P2012 (P0446) | Activated charcoal canister shut-off valve, ME-SFI fault code description, Plausibility | Activated charcoal canister shut-off valve ME-SFI - fault code description |
| P2013 (P0455) | Regeneration system Major leak (function chain) ME-SFI fault code description | Regeneration system leaking (causal chain) ME-SFI - fault code description |
| P2014 (P0422) | Regeneration system Minor leak (function chain) ME-SFI fault code description, microleak | Regeneration system leaking (causal chain) ME-SFI - fault code description |
| P2015 (P0440) | Regeneration system leak (function chain) ME-SFI fault code description | Regeneration system leaking (causal chain) ME-SFI - fault code description |
| P2016 (P0170) | Self-adaptation of mixture formation at limit, ME-SFI fault code description. For the right cylinder bank, at partial load. | Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2017 (P0170) | Self-adaptation of mixture formation at limit, ME-SFI fault code description. For the right cylinder bank, in idle | Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2018 (P0170) | Self-adaptation of mixture formation at limit, ME-SFI fault code description. For the right cylinder bank, between idle and partial load. | Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2019 (P0170) | Coolant antiboil protection, ME-SFI fault code description | Coolant antiboil protection, ME-SFI fault code description |
| P201A (P0341) | Camshaft Hall sensor, ME-SFI fault code description | Camshaft Hall sensor - fault code description ME |
| P201B (P0560) | Control unit voltage supply, ME-SFI fault code description | ME-SFI control unit voltage supply - fault code description |
| P201C (P0450) | Tank pressure sensor, ME-SFI fault code description | Tank pressure sensor ME - fault code description |
| P201D (P0201) | Fuel injection valves, Cylinder 1 ME-SFI fault code description | Fault code description for fuel injection valves, ME-SFI |
| P201E (P0204) | Fuel injection valves, Cylinder 4 ME-SFI fault code description | Fault code description for fuel injection valves, ME-SFI |
| P201F (P0203) | Fuel injection valves, Cylinder 3 ME-SFI fault code description | Fault code description for fuel injection valves, ME-SFI |
| P2020 (P0206) | Fuel injection valves, Cylinder 6 ME-SFI fault code description | Fault code description for fuel injection valves, ME-SFI |
| P2021 (P0202) | Fuel injection valves, Cylinder 2 ME-SFI fault code description | Fault code description for fuel injection valves, ME-SFI |
| P2022 (P0205) | Fuel injection valves, Cylinder 5 ME-SFI fault code description | Fault code description for fuel injection valves, ME-SFI |
| P2023 (P0410) | Air injection relay, ME-SFI fault code description | Air injection relay, ME-SFI fault code description |
| P2024 (P0412) | Air pump switchover valve, ME-SFI fault code description | Air pump switchover valve, ME-SFI fault code description |
| P2025 (P0446) | Activated charcoal canister shut-off valve, ME-SFI fault code description, Voltage supply | Activated charcoal canister shut-off valve ME-SFI - fault code description |
| P2026 (P0443) | Purge control valve, ME-SFI fault code description | Fault code description for purge control valve, ME |
| P2027 (P0403) | EGR [ARF] pressure transducer, ME-SFI fault code description | EGR [ARF] pressure transducer, ME-SFI fault code description |
| P202B (P0507) | Idle speed control, ME-SFI fault code description | Idle speed control - fault code description ME |
| P202C (P0115) | Coolant thermostat, ME-SFI fault code description | Coolant thermostat, ME-SFI fault code description |
| P202D (P0115) | Coolant temperature sensor, ME-SFI fault code description | Coolant temperature sensor ME-SFI - fault code description |
| P202E (P0120) | Throttle valve actuator, ME-SFI fault code description, Adjustment | Throttle valve actuator, ME-SFI fault code description |
| P202F (P0600) | CAN fault detection, ME-SFI - fault code description. CAN message from ABC control unit. | CAN fault detection ME - fault code description |
| P2030 (P0600) | CAN fault detection, ME-SFI fault code description. CAN message from electronic selector lever module control unit. | CAN fault detection ME - fault code description |
| P2031 (P0600) | CAN fault detection, ME-SFI fault code description. CAN message from steering column module | CAN fault detection ME - fault code description |
| P2032 (P0120) | Throttle valve actuator, ME-SFI fault code description, Actual value potentiometer | Throttle valve actuator, ME-SFI fault code description |
| P2033 (-) | Cruise control switch, ME-SFI fault code description | Cruise control switch, ME-SFI fault code description |
| P2034 (P0335) | Crankshaft position sensor, ME-SFI fault code description | Fault code description for crankshaft position sensor, ME-SFI |
| P2036 (P0600) | CAN fault detection, ME-SFI fault code description. CAN message from ESP control unit. | CAN fault detection ME - fault code description |
| P2037 (P0600) | CAN fault detection, ME-SFI fault code description. CAN message from ETC control unit Transmission 722.6 | CAN fault detection ME - fault code description |
| P2038 (-) | Left Knock sensor 2, ME-SFI fault code description | Knock sensor ME - fault code description |
| P2039 (-) | Oil sensor, ME-SFI fault code description, Oil level implausible | Oil sensor, ME-SFI fault code description |
| P203A (P0460) | Fuel tank fill level, ME-SFI fault code description | Fuel tank fill level, ME-SFI fault code description |
| P203B (P0221) | ME-SFI control unit, ME-SFI fault code description, Fault in function monitoring | ME-SFI control unit, ME-SFI fault code description |
| P203C (P0221) | ME-SFI control unit, ME-SFI fault code description, Fault in function monitoring | ME-SFI control unit, ME-SFI fault code description |
| P203D (P0370) | Angle deviation of camshaft relative to crankshaft, ME-SFI fault code description | Angle deviation of camshaft relative to crankshaft, ME-SFI fault code description |
| P203E (P0600) | CAN fault detection, ME-SFI fault code description, CAN message from instrument cluster | CAN fault detection ME - fault code description |
| P2040 (-) | Oil sensor, ME-SFI fault code description, Oil quality implausible | Oil sensor, ME-SFI fault code description |
| P2041 (-) | Oil sensor, ME-SFI fault code description, Water in engine oil | Oil sensor, ME-SFI fault code description |
| P2042 (-) | Safety fuel shutoff detected, ME-SFI fault code description | Safety fuel shutoff detected, ME-SFI fault code description |
| P2043 (P0300) | Misfire, ME-SFI fault code description, Sum, emission limit | Misfires - fault code description - ME |
| P2044 (P0301) | Misfire, ME-SFI fault code description. M1M Misfiring at cylinder 1, emission limit | Misfires - fault code description - ME |
| P2045 (P0304) | Misfire, ME-SFI fault code description. Misfiring at cylinder 4, emission limit. | Misfires - fault code description - ME |
| P2046 (P0303) | Misfire, ME-SFI fault code description. Misfiring at cylinder 3, emission limit. | Misfires - fault code description - ME |
| P2047 (P0306) | Misfire, ME-SFI fault code description. Misfiring at cylinder 6, emission limit. | Misfires - fault code description - ME |
| P2048 (P0302) | Misfire, ME-SFI fault code description. Misfiring at cylinder 2, emission limit. | Misfires - fault code description - ME |
| P2049 (P0305) | Misfire, ME-SFI fault code description. Misfiring at cylinder 5, emission limit. | Misfires - fault code description - ME |
| P2050 (P0300) | Misfire, ME-SFI fault code description, Sum, TWC-damaging | Misfires - fault code description - ME |
| P2051 (P0301) | Misfire, ME-SFI fault code description. Misfiring at cylinder 1, TWC-damaging | Misfires - fault code description - ME |
| P2052 (P0304) | Misfire, ME-SFI fault code description. Misfiring at cylinder 4, TWC-damaging | Misfires - fault code description - ME |
| P2053 (P303) | Misfire, ME-SFI fault code description. Misfiring at cylinder 3, TWC-damaging | Misfires - fault code description - ME |
| P2054 (P0306) | Misfire, ME-SFI fault code description. Misfiring at cylinder 6, TWC-damaging | Misfires - fault code description - ME |
| P2055 (P0302) | Misfire, ME-SFI fault code description. Misfiring at cylinder 2, TWC-damaging | Misfires - fault code description - ME |
| P2056 (P0305) | Misfire, ME-SFI fault code description. Misfiring at cylinder 5, TWC-damaging | Misfires - fault code description - ME |
| P205E (P0702) | ETC control unit, ME-SFI fault code description. Internal fault, Transmission 722.6 | ETC control unit, ME-SFI fault code description |
| P205F (P0753) | 1-2/4-5 shift solenoid valve, ME-SFI fault code description | Solenoid valve 1-2/4-5 for shift mechanism -fault code description ME |
| P2060 (P0758) | 2-3 shift solenoid valve, ME-SFI fault code description | Solenoid valve 2-3 for shift mechanism - fault code description ME |
| P2061 (P0763) | 3-4 shift solenoid valve, ME-SFI fault code description | Solenoid valve 3-4 for shift mechanism - fault code description ME |
| P2062 (P0743) | PWM torque converter lockup solenoid valve, ME-SFI fault code description | Pulse width modulation solenoid valve for torque converter lockup - fault code description ME |
| P2063 (P0748) | Modulating pressure control solenoid valve, ME-SFI fault code description | Modulating pressure control solenoid valve -fault code description ME |
| 2064 (P0748) | Shift pressure control solenoid valve, ME-SFI fault code description | Shift pressure control solenoid valve - fault code description ME |
| P2065 (P0702) | Supply voltage to valves, ME-SFI fault code description | Supply voltage for valves - fault code description ME |
| P2066 (P0715) | Supply voltage and speed sensors function, ME-SFI fault code description | Supply voltage and function of rpm sensors -fault code description ME |
| P2067 (P0705) | ETC control unit, ME-SFI fault code description. Selector lever module incorrectly coded Transmission 722.6 | ETC control unit, ME-SFI fault code description |
| P2068 (P0720) | ETC control unit, ME-SFI fault code description. CAN message from the rear wheels from ESP control unit missing or incorrect | ETC control unit, ME-SFI fault code description |
| P2069 (P0700) | Gear implausible or leak in transmission, ME-SFI fault code description | Gear implausible or leak in transmission, ME-SFI fault code description |
| P206A (P0700) | Command valve jams in pressure position, ME-SFI fault code description | Command valve jams in pressure position, ME-SFI fault code description |
| P206B (P0740) | Torque converter lock-up clutch, ME-SFI fault code description | Torque converter lockup clutch - fault code description ME |
| P206D (P0730) | Gear comparison (many times) negative, ME-SFI fault code description | Gear position comparison negative (on multiple occasions) - fault code description ME |
| P206E (-) | Transmission variant implausible, ME-SFI fault code description. Coded for manual transmission, vehicle has automatic transmission. | Transmission variant implausible, ME-SFI fault code description |
| P206F (-) | Transmission variant implausible, ME-SFI fault code description. Incorrectly coded or fault in CAN communication with ETC control unit | Transmission variant implausible, ME-SFI fault code description |
| P2070 (-) | Transmission variant implausible, ME-SFI fault code description | Transmission variant implausible, ME-SFI fault code description |
| P2072 (P0450) | Tank pressure sensor, Plausibility ME-SFI fault code description | Tank pressure sensor ME - fault code description |
| P2073 (-) | Electrical suction fan, ME-SFI fault code description | Electric suction fan, ME-SFI fault code description |
| P2074 (-) | Variable intake manifold switchover valve, ME-SFI fault code description | Variable intake manifold switchover valve, ME-SFI fault code description |
| P2075 (P0442) | Regeneration system lminor eak (function chain) ME-SFI fault code description system, microleak | Regeneration system leaking (causal chain) ME-SFI - fault code description |
| P2076 (-) | Oil sensor, ME-SFI fault code description, Oil temperature implausible | Oil sensor, ME-SFI fault code description |
| P2079 (-) | CAN fault detection, ME-SFI fault code description, VGB speed | CAN fault detection ME - fault code description |
| P207A (-) | CAN fault detection, ME-SFI fault code description, VGB speed | CAN fault detection ME - fault code description |
| P207B (-) | CAN fault detection, ME-SFI fault code description, Selector lever position | CAN fault detection ME - fault code description |
| P207D (-) | EIS control unit, ME-SFI fault code description | EIS control unit, ME-SFI fault code description |
| P207E (P0432) | Left Catalytic converter efficiency too low, ME-SFI fault code description | Fault code description - three-way catalytic converter effectiveness too low |
| P207F (-) | Aging of O2 sensor downstream TWC, ME-SFI fault code description. Left O2 sensor upstream TWC [KAT], correction variable exceeded | Aging of O2 sensor upstream of TWC - fault code description ME |
| P2080 (P0153) | Aging of O2 sensor downstream TWC, ME-SFI fault code description. Left O2 sensor upstream TWC [KAT], period duration | Aging of O2 sensor upstream of TWC - fault code description ME |
| P2081 (-) | O2 Sensor signal - ME-SFI fault code description. Left O2 sensor downstream TWC [KAT], no sensor status change | O2 sensor signal - fault code description ME |
| P2082 (P0150) | O2 Sensor signal, ME-SFI fault code description. Left O2 sensor upstream TWC [KAT], electrical fault | O2 sensor signal - fault code description ME |
| P2083 (P0156) | O2 Sensor signal, ME-SFI fault code description. Left O2 sensor downstream TWC [KAT], electrical fault | O2 sensor signal - fault code description ME |
| P2085 (P0173) | Self-adaptation of mixture formation at limit, ME-SFI fault code description. For the left cylinder bank, at partial load | Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2086 (P0173) | Self-adaptation of mixture formation at limit, ME-SFI fault code description. For the left cylinder bank, in idle | Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2087 (P0173) | Self-adaptation of mixture formation at limit, ME-SFI fault code description. For the left cylinder bank, between idle and partial load | Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2088 (P0155) | O2S-sensor heater, ME-SFI fault code description. Left O2 sensor upstream TWC [KAT], internal resistor | O2-sensor heating - fault code description ME-SFI |
| P2089 (P0161) | O2S-sensor heater, ME-SFI fault code description. Left O2 sensor downstream TWC [KAT], internal resistor | O2-sensor heating - fault code description ME-SFI |
| P2090 (-) | O2 sensor connectors swapped, ME-SFI fault code description | Sensor O2cconnectors swapped, ME-SFI fault code description |
| P2097 (-) | Throttle valve actuator, ME-SFI fault code description. Throttle valve jamming, iced up | Throttle valve actuator, ME-SFI fault code description |
| P2098 (-) | Crash signal implausible, ME-SFI fault code description | Crash signal implausible, ME-SFI fault code description |
| P20BE (P0135) | O2S-sensor heater, ME-SFI fault code description. Right O2 sensor upstream TWC [KAT], voltage supply | O2-sensor heating - fault code description ME |
| P20BF (P0135) | O2S-sensor heater, ME-SFI fault code description. Left O2 sensor upstream TWC [KAT], voltage supply | O2-sensor heating - fault code description ME |
| P20C2 (P0141) | O2S-sensor heater, ME-SFI fault code description. Right O2 sensor downstream TWC [KAT], voltage supply | O2-sensor heating - fault code description ME |
| P20C3 (P0141) | O2-sensor heater, ME-SFI fault code description. Left O2 sensor downstream TWC [KAT], voltage supply | O2-sensor heating - fault code description ME |
| P20Ca (P0500) | CAN fault detection, ME-SFI fault code description. Speed signal of left rear wheel from ESP control unit | CAN fault detection ME - fault code description |
| P20Cb (P0500) | CAN fault detection, ME-SFI fault code description. Speed signal of left front wheel from ESP control unit | CAN fault detection ME - fault code description |
| P20CC (-) | CAN fault detection, ME-SFI fault code description. CAN message from the ESP control unit is missing or incorrect | CAN fault detection ME - fault code description |
| P20CD (-) | Air conditioning (AC) system, ME-SFI fault code description. AC compressor torque implausible | Air conditioning (AC) system, ME-SFI fault code description |
| P20CE (-) | Air conditioning (AC) system, ME-SFI fault code description. Refrigerant pressure in air conditioning too high | Air conditioning (AC) system, ME-SFI fault code description |
| P20CF (P0120) | Fault code description for pedal value sensor, ME-SFI. Voltage difference between signal 1 and signal 2 | Pedal value sensor, ME-SFI fault code description |
| P20D0 (-) | Air conditioning (AC) system, ME-SFI fault code description. Air conditioning requests an implausible fan output | Air conditioning (AC) system, ME-SFI fault code description |
| P20D1 (-) | CAN fault detection, ME-SFI fault code description. Torque request from DTR control unit implausible | CAN fault detection ME - fault code description |
| P20D2 (-) | CAN fault detection, ME-SFI fault code description. CAN transmission error of torque request from DTR control unit | CAN fault detection ME - fault code description |
| P20D3 (-) | CAN fault detection, ME-SFI fault code description. CAN transmission error of torque request from DTR control unit | CAN fault detection ME - fault code description |
| P20D4 (-) | Active load limitation, ME-SFI fault code description | Active load limitation, ME-SFI fault code description |
| P20D5 (P0702) | ETC control unit, ME-SFI fault code description. Torque request from the ETC control unit is implausible. | ETC control unit, ME-SFI fault code description |
| P20D6 (P0702) | ETC control unit, ME-SFI fault code description. CAN transmission error for torque request from ETC control unit | ETC control unit, ME-SFI fault code description |
| P20D7 (P0702) | ETC control unit, ME-SFI fault code description. CAN transmission error for torque request from ETC control unit | ETC control unit, ME-SFI fault code description |
| P20D8 (-) | ESP control unit, ME-SFI fault code description, ESP fault | ESP control unit, ME-SFI fault code description |
| P20D9 (-) | CAN fault detection, ME-SFI fault code description. Torque request from ESP control unit implausible | CAN fault detection ME - fault code description |
| P20Da (-) | CAN fault detection, ME-SFI fault code description. CAN transmission error of torque request from ESP control unit | CAN fault detection ME - fault code description |
| P20Db (-) | CAN fault detection, ME-SFI fault code description. CAN transmission error of torque request from ESP control unit | CAN fault detection ME - fault code description |
| P20DC (P0120) | Fault code description for pedal value sensor, ME-SFI. Interruption at signal path 1 | Pedal value sensor, ME-SFI fault code description |
| P20DD (P0120) | Pedal value sensor, ME-SFI fault code description. Short-circuit at signal path 1 | Pedal value sensor, ME-SFI fault code description |
| P20DE (P0120) | Pedal value sensor, ME-SFI fault code description. Interruption at signal path 2 | Pedal value sensor, ME-SFI fault code description |
| P20DF (P0120) | Pedal value sensor, ME-SFI fault code description. Short-circuit at signal path 2 | Pedal value sensor, ME-SFI fault code description |
| P20E3 (P0120) | Voltage supply for Pedal value sensor, ME-SFI fault code description | Pedal value sensor, ME-SFI fault code description |
| P20E4 (-) | CAN fault detection, ME-SFI fault code description. Implausible signal from the stop lamp switch | CAN fault detection ME - fault code description |
| P20E5 (-) | CAN fault detection, ME-SFI fault code description. CAN transmission error of signal from stop lamp switch | CAN fault detection ME - fault code description |
| P20E6 (-) | CAN fault detection, ME-SFI fault code description. CAN transmission error of signal from stop lamp switch | CAN fault detection ME - fault code description |
| ENGINES 113.940 /942 /943 up to 31.5.00, 113.961 | ||
| No fault code | No fault detected Depending on the complaint, carry out testing of ME-SFI electrical system in full |
ME-SFI gasoline injection system, testing of electrical system ME-SFI ignition system, testing of electrical system |
| ME-SFI idle speed control/electronic accelerator, testing of electrical system | ||
| ME-SFI cruise control with variable speed limit, testing of electrical system | ||
| P0100 | Hot-film mass air flow sensor (B2/5) | Hot-film mass air flow sensor - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for hot film mass air flow sensor, ME-SFI | Fault code description - ME-SFI - hot film mass air flow sensor | |
| P0105 | Pressure sensor (B28) | Pressure sensor - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for pressure sensor, ME-SFI | Fault code description - ME-SFI - pressure sensor | |
| P0110 | Intake air temperature sensor (in the hot film mass air flow sensor B2/5) | Intake air temperature sensor - ME-SFI gasoline injection system - Testing electrical system |
| Intake air temperature sensor Fault code description, ME-SFI |
Fault code description - ME-SFI - intake air temperature sensor | |
| P0115 | Coolant temperature sensor (B11/4) | Coolant temperature sensor - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for coolant temperature sensor, ME-SFI | Fault code description - ME-SFI - coolant temperature sensor | |
| P0120 | Actual value potentiometer in the throttle valve actuator (M16/6) | Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics |
| Fault code description for actual value potentiometer in the throttle valve actuator, ME-SFI | ME-SFI actual value potentiometer in the throttle valve actuator, fault code description | |
| P0130 | A Oxygen sensor on right upstream of TWC (G3/4) B Oxygen sensor on right upstream of TWC (G3/4) voltage increase too small |
AD07.61-P-6000-11A |
| Fault code description for oxygen sensor signal, ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0133 | A Oxygen sensor on right upstream of TWC (G3/4) aging correction variable exceeded B Oxygen sensor on right upstream of TWC (G3/4) aging of cycle duration too long C Oxygen sensor on right upstream of TWC (G3/4) aging of oxygen sensor too slow |
AD07.61-P-6000-11A |
| Fault code description for aging of oxygen sensor upstream of TWC, ME-SFI | O2 Fault code description - ME-SFI - ageing of oxygen sensor upstream of TWC | |
| P0135 | Oxygen sensor heating of oxygen sensor on right upstream of TWC (G3/4) | AD07.61-P-6000-13A |
| Fault code description for oxygen sensor heating, ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0136 | Oxygen sensor on right downstream of TWC (G3/6) with CODE (925) low-emission EURO3 | Oxygen sensor signal on right downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for oxygen sensor signal, ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0140 | Oxygen sensor on right upstream of TWC (G3/4) | AD07.61-P-6000-11A |
| Fault code description for oxygen sensor signal, ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0141 | Oxygen sensor heating of oxygen sensor on right downstream of TWC (G3/6) with CODE (925) low-emission EURO3 | Oxygen sensor heating on right downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for oxygen sensor heating, ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0150 | A Oxygen sensor on left upstream of TWC (G3/3) B Oxygen sensor on left upstream of TWC (G3/3) voltage increase too small |
AD07.61-P-6000-10A |
| Fault code description for oxygen sensor signal, ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0153 | A Oxygen sensor on left upstream of TWC (G3/3) aging of correction variable exceeded B Oxygen sensor on left upstream of TWC (G3/3) aging of cycle duration too long C Oxygen sensor on left upstream of TWC (G3/3) aging of oxygen sensor too slow |
AD07.61-P-6000-10A |
| Fault code description for aging of oxygen sensor upstream of TWC, ME-SFI | O2 Fault code description - ME-SFI - ageing of oxygen sensor upstream of TWC | |
| P0155 | Oxygen sensor heating of oxygen sensor on left upstream of TWC (G3/3) | AD07.61-P-6000-12A |
| Fault code description for oxygen sensor heating, ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0156 | Oxygen sensor on left downstream of TWC (G3/5) with CODE (925) low-emission EURO3 | Oxygen sensor signal on left downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for oxygen sensor signal, ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0160 | Oxygen sensor on left downstream of TWC (G3/5) with CODE (925) low-emission EURO3 | Oxygen sensor signal on left downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for Oxygen sensor signal, ME-SFI | Fault code description - ME-SFI - oxygen sensor signal | |
| P0161 | Oxygen sensor heating of Oxygen sensor on left downstream of TWC (G3/5) with CODE (925) low-emission EURO3 | Oxygen sensor heating on left downstream of TWC - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for oxygen sensor heating, ME-SFI | Oxygen sensor heating, fault code description ME-SFI | |
| P0170 | A Self-adaptation of the "partial load" mixture formation for right cylinder bank to limit value of ME-SFI control module (N3/10) B Self-adaptation of the "idle" mixture formation for right cylinder bank to limit value of ME-SFI control module (N3/10) |
Air leak, fuel injectors of diaphragm-type pressure regulating valve, wear to engine |
| Fault code description for self-adaptation of mixture formation to limit, ME-SFI | Self-adaptation of mixture formation to limit, fault code description ME-SFI | |
| P0173 | A Self-adaptation of the "partial load" mixture formation for left cylinder bank to limit value of ME-SFI control module (N3/10) B Self-adaptation of the "idle" mixture formation for left cylinder bank to limit value of ME-SFI control module (N3/10) |
Air leak, fuel injectors of diaphragm-type pressure regulating valve, wear to engine |
| Fault code description for self-adaptation of mixture formation to limit, ME-SFI | Self-adaptation of mixture formation to limit, fault code description ME-SFI | |
| P0201 | Fuel injector (Y62y1) cylinder 1 | Fuel injector (Y62/1) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0202 | Fuel injector (Y62y2) cylinder 2 | Fuel injector (Y62/2) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0203 | Fuel injector (Y62y3) cylinder 3 | Fuel injector (Y62/3) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0204 | Fuel injector (Y62y4) cylinder 4 | Fuel injector (Y62/4) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0205 | Fuel injector (Y62y5) cylinder 5 | Fuel injector (Y62/5) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0206 | Fuel injector (Y62y6) cylinder 6 | Fuel injector (Y62/6) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0207 | Fuel injector (Y62y7) cylinder 7 | Fuel injector (Y62/7) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0208 | Fuel injector (Y62y8) cylinder 8 | Fuel injector (Y62/8) - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for fuel injectors, ME-SFI | Fault code description - ME-SFI - fuel injectors | |
| P0300 | A Misfire B Misfire "damaging to TWC" |
Primary voltage (T1/1) - ME-SFI ignition system - Testing electrics Primary voltage (T1/2) - ME-SFI ignition system - Testing electrics Primary voltage (T1/3) - ME-SFI ignition system - Testing electrics Primary voltage (T1/4) - ME-SFI ignition system - Testing electrics Primary voltage (T1/5) - ME-SFI ignition system - Testing electrics Primary voltage (T1/6) - ME-SFI ignition system - Testing electrics Primary voltage (T1/7) - ME-SFI ignition system - Testing electrics Primary voltage (T1/8) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0301 | A Misfire in cylinder 1 B Misfire in cylinder 1 "damaging to TWC" |
Primary voltage (T1/1) - ME-SFI ignition system - Testing electrics Primary voltage (T1/2) - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0302 | A Misfire in cylinder 2 B Misfire in cylinder 2 "damaging to TWC" |
Primary voltage (T1/2) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0303 | A Misfire in cylinder 3 B Misfire in cylinder 3 "damaging to TWC" |
Primary voltage (T1/3) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0304 | A Misfire in cylinder 4 B Misfire in cylinder 4 "damaging to TWC" |
Primary voltage (T1/4) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0305 | A Misfire in cylinder 5 B Misfire in cylinder 5 "damaging to TWC" |
Primary voltage (T1/5) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0306 | A Misfire in cylinder 6 B Misfire in cylinder 6 "damaging to TWC" |
Primary voltage (T1/6) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0307 | A Misfire in cylinder 7 B Misfire in cylinder 7 "damaging to TWC" |
AD07.61-P-6001-20A Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0308 | A Misfire in cylinder 8 B Misfire in cylinder 8 "damaging to TWC" |
Primary voltage (T1/8) - ME-SFI ignition system - Testing electrics Ignition voltage - ME-SFI ignition system - Testing electrics Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Fuel injectors - Testing hydraulic system, ME-SFI fuel injectors Compression pressure |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0325 | Knock sensor on right | Connector line Knock sensor |
| Fault code description for knock sensor, ME-SFI | Fault code description - ME-SFI - knock sensor | |
| P0330 | Knock sensor on left | Connector line Knock sensor |
| Fault code description for knock sensor, ME-SFI | Fault code description - ME-SFI - knock sensor | |
| P0335 | Crankshaft position sensor (L5) | Crankshaft position sensor - ME-SFI ignition system - Testing electrics |
| Fault code description for crankshaft position sensor, ME-SFI | Fault code description - ME-SFI - crankshaft position sensor | |
| P0341 | Camshaft Hall sensor (B6/1) | Camshaft Hall sensor - ME-SFI ignition system - Testing electrics |
| Fault code description for camshaft Hall sensor, ME-SFI | Fault code description - ME-SFI - camshaft Hall sensor | |
| P0370 | Angle deviation for camshaft to crankshaft | Check basic adjustment of camshafts |
| P0400 | Exhaust gas recirculation malfunction (causal chain) | EGR transducer - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for exhaust gas recirculation malfunction (causal chain), ME-SFI | Exhaust gas recirculation malfunction (causal chain), fault code description ME-SFI | |
| P0410 | Secondary air injection malfunction (causal chain) with CODE (925) low-emission EURO3/4 | Secondary air injection relay, testing of electrical system, ME-SFI gasoline injection system |
| Air pump switchover valve - Testing electrical system, ME-SFI gasoline injection system | ||
| Secondary air injection - Testing electrical system, ME-SFI gasoline injection system | ||
| Fault code description for secondary air injection malfunction (causal chain), ME-SFI | ME-SFI secondary air injection malfunction (causal chain) - Fault code description | |
| P0422 | Effect of right three-way catalytic converter too low | Right three-way catalytic converter |
| Fault code description for three-way catalytic converter effect too low, ME-SFI | Fault code description - three-way catalytic converter effect too low | |
| P0432 | Effect of left three-way catalytic converter too low | Left three-way catalytic converter |
| Fault code description for three-way catalytic converter effect too low, ME-SFI | Fault code description - three-way catalytic converter effect too low | |
| P0440 | Purge system leak (causal chain) | Purge control valve vacuum control - ME-SFI gasoline injection system - Testing electrical system |
| Purge system - Testing electrical system, ME-SFI gasoline injection system | ||
| Fault code description for purge system leak (causal chain), ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0441 | Purge control valve (Y58/1) | Purge control valve activation - ME-SFI gasoline injection system - Testing electrical system |
| Function | Purge control valve vacuum control - ME-SFI gasoline injection system - Testing electrical system | |
| Fault code description for purge system leak (causal chain), ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0442 | Purge system slight leak | Purge system - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for purge system leak (causal chain), ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0443 | Purge control valve (Y58/1) | Purge control valve activation - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for purge control valve, ME-SFI | Fault code description - ME-SFI - purge control valve | |
| P0446 | A Activated charcoal canister shutoff valve (causal chain) | Activated charcoal canister shutoff valve - Testing electrical system, ME-SFI gasoline injection system |
| B Activated charcoal canister shutoff valve (Y58/4) | Tank pressure sensor - Testing electrical system, ME-SFI gasoline injection system | |
| Fault code description for activated charcoal canister shutoff valve, ME-SFI | Fault code description for activated charcoal canister shutoff valve, ME-SFI | |
| P0450 | A Tank pressure sensor (B4/3) electrical fault B Tank pressure sensor (B4/3) electrical vibrations |
Tank pressure sensor - Testing electrical system, ME-SFI gasoline injection system Activated charcoal canister blocked |
| Fault code description for tank pressure sensor, ME-SFI | Fault code description for tank pressure sensor, ME-SFI | |
| P0455 | Purge system with severe leak or voltage supply for tank pressure sensor (B4/3) | Purge system - Testing electrical system, ME-SFI gasoline injection system |
| Tank pressure sensor - Testing electrical system, ME-SFI gasoline injection system | ||
| Fault code description for purge system leak (causal chain), ME-SFI | Regeneration system leaking (causal chain) ME-SFI fault code description | |
| P0460 | Fuel level gage sensor | Read out IC |
| Fault code description for misfires, ME-SFI | Fault code description - ME-SFI - misfires | |
| P0500 | A front left vehicle speed signal B rear left vehicle speed signal |
Check ASR in chassis diagnosis manual, index 9 AD42.45-P-1000AZ |
| Fault code description for vehicle speed signal, ME-SFI | Fault code description - ME-SFI - vehicle speed signal | |
| P0507 | Idle speed control implausible | Pedal value sensor signal, testing of electrical system, ME-SFI idle speed control/electronic accelerator Pedal value sensor signal, testing of electrical system, ME-SFI idle speed control/electronic accelerator Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics |
| Fault code description for idle speed control, ME-SFI | Fault code description - ME-SFI - idle speed control | |
| P0520 | Oil pressure sensor for cylinder cut-out system (CODE (479) for cylinder cut-out system) | refer to STAR DIAGNOSIS |
| Fault code description for oil pressure sensor for cylinder cut-out system, ME-SFI | AD07.61-P-4000-58B | |
| P0560 | Voltage supply to ME-SFI control module (N3/10) | ME-SFI gasoline injection system electrical system, check ME-SFI control module terminal 30 |
| ME-SFI control module, terminal 87 - ME-SFI gasoline injection system - Testing electrical system | ||
| Fault code description for control module voltage supply, ME-SFI | ME-SFI control module voltage supply - Fault code description | |
| P0565 | Pushbutton switch for variable cruise control (S40/4) | Cruise control pushbutton switch, testing of electrical system, ME-SFI cruise control with variable speed limit |
| P0600 | CAN of ESP | CAN data bus - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for CAN damaged, ME-SFI | Fault code description - ME-SFI - CAN faulty | |
| P0604 | A ME-SFI control module (N3/10) B ME-SFI control module (N3/10) |
N3/10 |
| P0605 | ME-SFI control module (N3/10) | N3/10 |
| P0700 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for gear implausible or transmission with leaks, ME-SFI | Fault code description - ME-SFI - gear implausible or transmission with leaks | |
| Fault code description for command valve sticks in pressure position, ME-SFI | Fault code description - ME-SFI - command valve sticks in pressure position | |
| P0702 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for ETC control module, ME-SFI | Fault code description - ME-SFI - ETC control module | |
| Fault code description for valve supply voltage, ME-SFI | Fault code description - ME-SFI - valve supply voltage | |
| P0715 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for supply voltage and function of RPM sensors, ME-SFI | Fault code description - ME-SFI - supply voltage and function of RPM sensors | |
| P0720 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for CAN fault identification, ME-SFI | Fault code description - ME-SFI - CAN fault identification | |
| P0730 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for gear comparison (multiple times) negative, ME-SFI | Fault code description - ME-SFI - gear comparison (multiple times) negative | |
| P0740 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for torque converter lockup clutch, ME-SFI | Fault code description - ME-SFI - torque converter lockup clutch | |
| P0743 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for PWM-solenoid of torque converter lockup, ME-SFI | Fault code description - ME-SFI - PWM-solenoid of torque converter lockup | |
| P0748 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for modulating pressure control solenoid, ME-SFI | Fault code description - ME-SFI - modulating pressure control solenoid | |
| Fault code description for switching pressure control solenoid, ME-SFI | ME-SFI shifting pressure control solenoid valve - Fault code description | |
| P0753 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for 1-2/4-5 shift solenoid, ME-SFI | ME-SFI 1-2/4-5 shifting solenoid valve - Fault code description | |
| P0758 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for 2 - 3 shift solenoid, ME-SFI | ME-SFI 2-3 shifting solenoid valve - Fault code description | |
| P0763 | Read out diagnostic trouble code memory for ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| Fault code description for 3 - 4 shift solenoid, ME-SFI | ME-SFI 3-4 shifting solenoid valve - Fault code description | |
| P0801 | Electric suction-type fan for engine/AC (M4/3) | Suction-type fan control module - Testing electrical system, ME-SFI gasoline injection system |
| P0802 | Variable intake manifold switchover valve (Y22/6) | Variable intake manifold switchover valve - ME-SFI gasoline injection system - Testing electrical system |
| P0809 | Angle deviation for camshaft to crankshaft | Check basic adjustment of camshafts |
| P0811 | CAN of EIS | CAN data bus - ME-SFI gasoline injection system - Testing electrical system |
| P1031 | Oxygen sensors upstream of TWC (G3/3 and G3/4) exchanged | Check connectors |
| P1177 | Oil sensor (oil level/temperature/quality) (B40): oil temperature implausible | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1178 | Oil sensor (oil level/temperature/quality) (B40): oil level implausible | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1179 | Oil sensor (oil level/temperature/quality) (B40): oil quality implausible | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1180 | Oil sensor (oil level/temperature/quality) (B40): oil temperature too high | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1181 | Electric suction-type fan for engine/AC (M4/3) | Suction-type fan control module - Testing electrical system, ME-SFI gasoline injection system |
| P1183 | Cylinder cut-out system valve on right cylinder bank(Y80) CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system valve, ME-SFI | AD07.61-P-4000-56B | |
| P1184 | Cylinder cut-out system valve on left cylinder bank (Y81) CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system valve, ME-SFI | AD07.61-P-4000-56B | |
| P1185 | Oil sensor (oil level/temperature/quality) (B40): water in the engine oil | Oil sensor - ME-SFI gasoline injection system - Testing electrical system |
| P1186 | Safety fuel shutoff detected | Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics Throttle valve actuator actuation - ME-SFI idle speed control/electronic accelerator - Testing electrics Throttle valve actuator sluggish/sticks Check intake train for residue |
| P1225 | Variable intake manifold switchover valve (Y22/6) | Variable intake manifold switchover valve - ME-SFI gasoline injection system - Testing electrical system |
| P1233 | Throttle valve actuator (M16/6) sticks (iced up) | Actuator |
| P1355 | Cylinder cut-out system valve on right cylinder bank (Y80), CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description when cylinder cut-out system valves do not close with cylinder cutout system OFF, ME-SFI | AD07.61-P-4000-52B | |
| P1356 | Cylinder cut-out system valve on left cylinder bank (Y81), CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description when cylinder cut-out system valves do not close with cylinder cut-out system OFF, ME-SFI | AD07.61-P-4000-52B | |
| P1357 | Cylinder cut-out system ON: Intake valve of cylinder 2, 3, 5 or 8 is still actuated, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system (causal chain) | AD07.61-P-4000-54B | |
| P1358 | Cylinder cut-out system OFF: Exhaust valve of cylinder 5 is not actuated, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system (causal chain), ME-SFI | AD07.61-P-4000-54B | |
| P1359 | Cylinder cut-out system OFF: Exhaust valve of cylinder 2 is not actuated, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system (causal chain), ME-SFI | AD07.61-P-4000-54B | |
| P1360 | Cylinder cut-out system OFF: Exhaust valve of cylinder 3 is not actuated, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system (causal chain), ME-SFI | AD07.61-P-4000-54B | |
| P1361 | Cylinder cut-out system OFF: exhaust valve of cylinder 8 is not actuated, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for cylinder cut-out system (causal chain), ME-SFI | AD07.61-P-4000-54B | |
| P1366 | Emission throttle switchover valve, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description for emission throttle switchover valve, ME-SFI | AD07.61-P-4000-57B | |
| P1380 | One intake valve of a cylinder is not actuated with cylinder cut-out system OFF, CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description when one intake valve of a cylinder is not actuated with cylinder cutout system OFF, ME-SFI | AD07.61-P-4000-55B | |
| P1386 | Anti-knock control by the ME-SFI control module (N3/10) at the control stop | Increased tendency to knock due to poor fuel, coked combustion chambers or mechanical damage |
| Fault code description for antiknock control in the computer error control module, ME-SFI | AD07.61-P-4000-41A | |
| P1400 | EGR transducer (Y31/1) | EGR transducer - ME-SFI gasoline injection system - Testing electrical system |
| Fault code description for EGR transducer, ME-SFI | ME-SFI EGR transducer - Fault code description | |
| P1420 | Air pump switchover valve (Y32) with CODE (925) low-emission EURO3 | Air pump switchover valve - Testing electrical system, ME-SFI gasoline injection system |
| Fault code description for secondary air injection, ME-SFI | ME-SFI secondary air injection - Fault code description | |
| P1453 | Air pump relay with CODE (925) low-emission EURO3 | Secondary air injection relay, testing of electrical system, ME-SFI gasoline injection system |
| Fault code description for secondary air injection, ME-SFI | ME-SFI secondary air injection - Fault code description | |
| P1491 | Refrigerant pressure in the air conditioning too high | Check air conditioning |
| P1542 | Pedal value sensor (B37) | Pedal value sensor signal, testing of electrical system, ME-SFI idle speed control/electronic accelerator |
| Pedal value sensor signal, testing of electrical system, ME-SFI idle speed control/electronic accelerator | ||
| Fault code description for pedal value sensor, ME-SFI | ME-SFI pedal value sensor - Fault code description | |
| P1570 | Start authorization from the DAS not granted A. Start attempted with locked DAS B. CAN from DAS control module to ME-SFI control module (N3/10) damaged C. ME-SFI control module and DAS control module do not match |
Incorrect operation AD80.35-P-1000AZ AD80.35-P-1000BZ CAN data bus - ME-SFI gasoline injection system - Testing electrical system Check control modules and part no. |
| P1580 | Throttle valve actuator (M16/6) | Throttle valve actuator signal - ME-SFI idle speed control/electronic accelerator - Testing electrics |
| Throttle valve actuator actuation - ME-SFI idle speed control/electronic accelerator - Testing electrics | ||
| Fault code description for throttle valve actuator, ME-SFI | ME-SFI throttle valve actuator - Fault code description | |
| P1584 | Stop lamp switch | Check ASR in chassis diagnosis AD42.45-P-1000AZ |
| P1603 | CAN of EIS | CAN data bus - ME-SFI gasoline injection system - Testing electrical system |
| P1605 | Signal for poor road detection (through comparison of wheel speeds) | Check ASR in chassis diagnosis, AD42.45-P-1000AZ |
| P1642 | ME-SFI control module (N3/10) coded incorrectly | Check/correct variant coding |
| P1644 | Transmission version cannot be checked due to undervoltage at the ETC control module (N15/3) | ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM |
| P1666 | Cylinder cut-out system valve does not open with cylinder cut-out system ON , CODE (479) for cylinder cut-out system | refer to STAR DIAGNOSIS |
| Fault code description when cylinder cut-out system valve does not open with cylinder cut-out system ON, ME-SFI | AD07.61-P-4000-53B | |
| P1681 | Crash signal implausible as of 06/98 | Crash signal - Testing ME-SFI electrical system |
| P1747 | A CAN fault: transmission protection malfunction from the ETC control module (N15/3) B CAN fault: instrument cluster |
ELECTRONIC TRANSMISSION CONTROL (ETC), TESTING ELECTRICAL SYSTEM Check instrument cluster, communication diagnosis AD54.30-P-1000AZ |
| Fault code description for CAN damaged, ME-SFI | Fault code description - ME-SFI - CAN faulty | |
| ENGINES 113.940 /941 /942 /943 /960 as of 1.6.00 ENGINES 113.948 /961 /963 /964 /965 /966 /967 /968 / 969 /971 |
||
| P2001 (P0400) | Exhaust gas recirculation malfunction (function chain) - fault code description ME | Exhaust gas recirculation malfunction (function chain), ME-SFI fault code description |
| P2003 (P0410) | ME secondary air injection malfunction (causal chain) - fault code description | ME secondary air injection malfunction (causal chain) - fault code description |
| P2004 (P0100) | Hot-film mass-air sensor ME - fault code description | Hot-film mass-air sensor ME-SFI - fault code description |
| P2005 (P0115) | Coolant temperature sensor ME - fault code description | Coolant temperature sensor ME-SFI - fault code description |
| P2006 (P0110) | Intake air temperature sensor ME - fault code description | Intake air temperature sensor ME-SFI - fault code description |
| P2007 (P0105) | Pressure sensor ME - fault code description | Pressure sensor ME-SFI - fault code description |
| P2008 (P0135) | O2-sensor heating - fault code description ME Right O2 sensor upstream of TWC, internal resistance |
O2-sensor heating - fault code description ME-SFI |
| P2009 (P0141) | O2-sensor heating - fault code description ME Right O2 sensor upstream of TWC, internal resistance |
O2-sensor heating - fault code description ME-SFI |
| P200A (-) | Anti-knock control in the control unit - hardware fault - fault code description ME | Anti-knock control in the hardware fault control unit, ME-SFI fault code description |
| P200B (P0422) | Fault code description - right three-way catalytic converter effectiveness too low | Fault code description - three-way catalytic converter effectiveness too low |
| P200C (-) | Aging of O2
sensor upstream of TWC - fault code description ME Right O2 sensor upstream of TWC, correction parameter limit exceeded |
Aging of O2 sensor upstream of TWC - fault code description ME |
| P200D (P0133) | Aging of O2
sensor upstream of TWC - fault code description ME Right O2 sensor upstream of TWC, cycle duration |
Aging of O2 sensor upstream of TWC - fault code description ME |
| P200E (-) | O2 sensor signal - fault code description ME Right O2 sensor downstream of TWC, no sensor condition change |
O2 sensor signal - fault code description ME |
| P200F (P0130) | O2 sensor signal - fault code description ME Right O2 sensor upstream of TWC, electrical fault |
O2 sensor signal - fault code description ME |
| P2010 (P0136) | O2 sensor signal - fault code description ME Right O2 sensor downstream of TWC, electrical fault |
O2 sensor signal - fault code description ME |
| P2011 (-) | Right Knock sensor 1 ME - fault code description | Knock sensor ME - fault code description |
| P2012 (P0446) | Activated charcoal canister shut-off valve ME - fault code description, Plausibility | Activated charcoal canister shut-off valve ME-SFI - fault code description |
| P2013 (P0455) | Purge control system has major leak (function chain) Fault code description ME | Regeneration system leaking (causal chain) ME-SFI |
| P2014 (P0422) | Purge control system has minor leak (function chain) Fault code description ME | Regeneration system leaking (causal chain) ME-SFI |
| P2015 (P0440) | Purge control system has leak (function chain) Fault code description ME | Regeneration system leaking (causal chain) ME-SFI |
| P2016 (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME For the right cylinder bank, at partial load |
Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2017 (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME For the right cylinder bank, when idling |
Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2018 (-) | Self-adaptation of mixture formation at its limit -fault code description ME For the right cylinder bank, between idle and partial load |
Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2019 (-) | Antiboil protection for coolant - fault code description ME | Coolant antiboil protection, ME-SFI fault code description |
| P201A (P0341) | Camshaft Hall sensor - fault code description ME | Camshaft Hall sensor - fault code description ME |
| P201B (P0560) | ME control unit voltage supply - fault code description | ME-SFI control unit voltage supply - fault code description |
| P201C (P0450) | Tank pressure sensor ME - fault code description | Tank pressure sensor ME - fault code description |
| P201D (P0201) | Fault code description for fuel injection valves, ME, Cylinder 1 | Fault code description for fuel injection valves, ME-SFI |
| P201E (P0205) | Fault code description for fuel injection valves, ME, Cylinder 5 | Fault code description for fuel injection valves, ME-SFI |
| P201F (P0204) | Fault code description for fuel injection valves ME, Cylinder 4 | Fault code description for fuel injection valves, ME-SFI |
| P2020 (P0202) | Fault code description for fuel injection valves ME, Cylinder 2 | Fault code description for fuel injection valves, ME-SFI |
| P2021 (P0206) | Fault code description for fuel injection valves, ME, Cylinder 6 | Fault code description for fuel injection valves, ME-SFI |
| P2022 (P0203) | Fault code description for fuel injection valves ME, Cylinder 3 | Fault code description for fuel injection valves, ME-SFI |
| P2023 (P0410) | Air injection relay - fault code description ME | Air injection relay, ME-SFI fault code description |
| P2024 (P0412) | Air pump switchover valve - fault code description, ME | Air pump switchover valve, ME-SFI fault code description |
| P2025 (P0446) | Activated charcoal canister shut-off valve ME - fault code description Voltage supply |
Activated charcoal canister shut-off valve ME-SFI - fault code description |
| P2026 (P0443) | Fault code description for purge control valve, ME | Fault code description for purge control valve, ME |
| P2027 (P0403) | EGR [ARF] vacuum transducer - fault code description ME | EGR [ARF] pressure transducer, ME-SFI fault code description |
| P202B (P0507) | Idle speed control - fault code description ME | Idle speed control - fault code description ME |
| P202C (P0115) | Coolant thermostat - fault code description, ME | Coolant thermostat, ME-SFI fault code description |
| P202D (P0115) | Coolant temperature sensor ME - fault code description | Coolant temperature sensor ME-SFI - fault code description |
| P202E (P0120) | Throttle valve actuator ME - fault code description, Adjustment | Throttle valve actuator, ME-SFI fault code description |
| P202F (P0600) | CAN fault detection ME - fault code description CAN message from ABC control unit |
CAN fault detection ME - fault code description |
| P2030 (P0600) | CAN fault detection ME - fault code description CAN message from electronic selector lever module control unit |
CAN fault detection ME - fault code description |
| P2031 (P0600) | CAN fault detection ME - fault code description CAN message from steering column module |
CAN fault detection ME - fault code description |
| P2032 (P0120) | Throttle valve actuator ME - fault code description Actual value potentiometer |
Throttle valve actuator, ME-SFI fault code description |
| P2033 (-) | Cruise control pushbutton switch - fault code description ME | Cruise control switch, ME-SFI fault code description |
| P2034 (P0335) | Fault code description for crankshaft position sensor, ME | Fault code description for crankshaft position sensor, ME-SFI |
| P2036 (P0600) | CAN fault detection ME - fault code description CAN message from ESP control unit |
CAN fault detection ME - fault code description |
| P2037 (P0600) | CAN fault detection ME - fault code description CAN message from ETC [EGS] control unit Transmission 722.6 |
CAN fault detection ME - fault code description |
| P2038 (-) | Knock sensor ME - fault code description Left knock sensor 2 |
Knock sensor ME - fault code description |
| P2039 (-) | Oil sensor - fault code description, ME Oil level implausible |
Oil sensor, ME-SFI fault code description |
| P203A (P0460) | Fill level of fuel tank - fault code description ME | Fuel tank fill level, ME-SFI fault code description |
| P203B (P0221) | ME control unit - fault code description, ME Fault in function monitoring |
ME-SFI control unit, ME-SFI fault code description |
| P203C (P0221) | ME control unit - fault code description, ME Fault in function monitoring |
ME-SFI control unit, ME-SFI fault code description |
| P203D (P0370) | Angular deviation of camshaft relative to crankshaft - fault code description ME | Angle deviation of camshaft relative to crankshaft, ME-SFI fault code description |
| P203E (P0600) | CAN fault detection ME - fault code description CAN message from instrument cluster |
CAN fault detection ME - fault code description |
| P2040 (-) | Oil sensor - fault code description, ME Oil quality implausible |
Oil sensor, ME-SFI fault code description |
| P2041 (-) | Oil sensor - fault code description, ME Water in engine oil |
Oil sensor, ME-SFI fault code description |
| P2042 (-) | Safety fuel cut-off detected - fault code description ME | Safety fuel shutoff detected, ME-SFI fault code description |
| P2043 (P0300) | Fault code description - ME - misfires Sum, emission limit |
Misfires - fault code description - ME |
| P2044 (P0301) | Fault code description - ME - misfires Misfires on cylinder 1, emission limit |
Misfires - fault code description - ME |
| P2045 (P0305) | Fault code description - ME - misfires Misfires on cylinder 5, emission limit |
Misfires - fault code description - ME |
| P2046 (P0304) | Fault code description - ME - misfires Misfires on cylinder 4, emission limit |
Misfires - fault code description - ME |
| P2047 (P0302) | Fault code description - ME - misfires Misfires on cylinder 2, emission limit |
Misfires - fault code description - ME |
| P2048 (P0306) | Fault code description - ME - misfires Misfires on cylinder 6, emission limit |
Misfires - fault code description - ME |
| P2049 (P0303) | Fault code description - ME - misfires Misfires on cylinder 3, emission limit |
Misfires - fault code description - ME |
| P204A (P0307) | Fault code description - ME - misfires Misfires on cylinder 7, emission limit |
Misfires - fault code description - ME |
| P204B (P0308) | Fault code description - ME - misfires Misfires on cylinder 8, emission limit |
Misfires - fault code description - ME |
| P2050 (P0300) | Fault code description - ME - misfires Sum, damaging to TWC |
Misfires - fault code description - ME |
| P2051 (P0301) | Fault code description - ME - misfires Misfires on cylinder 1, damaging to TWC |
Misfires - fault code description - ME |
| P2052 (P0305) | Fault code description - ME - misfires Misfires on cylinder 5, damaging to TWC |
Misfires - fault code description - ME |
| P2053 (P0304) | Fault code description - ME - misfires Misfires on cylinder 4, damaging to TWC |
Misfires - fault code description - ME |
| P2054 (P0302) | Fault code description - ME - misfires Misfires on cylinder 2, damaging to TWC |
Misfires - fault code description - ME |
| P2055 (P0306) | Fault code description - ME - misfires Misfires on cylinder 6, damaging to TWC |
Misfires - fault code description - ME |
| P2056 (P0303) | Fault code description - ME - misfires Misfires on cylinder 3, damaging to TWC |
Misfires - fault code description - ME |
| P2057 (P0307) | Fault code description - ME - misfires Misfires on cylinder 7, damaging to TWC |
Misfires - fault code description - ME |
| P2058 (P0308) | Fault code description - ME - misfires Misfires on cylinder 8, damaging to TWC |
Misfires - fault code description - ME |
| P205E (P0702) | ETC control unit ME - fault code description | ETC control unit, ME-SFI fault code description |
| P205F (P0753) | Solenoid valve 1-2/4-5 for shift mechanism - fault code description ME | Solenoid valve 1-2/4-5 for shift mechanism -fault code description ME |
| P2060 (P0758) | Solenoid valve 2-3 for shift mechanism - fault code description ME | Solenoid valve 2-3 for shift mechanism - fault code description ME |
| P2061 (P0763) | Solenoid valve 3-4 for shift mechanism - fault code description ME | Solenoid valve 3-4 for shift mechanism - fault code description ME |
| P2062 (P0743) | Pulse width modulation solenoid valve for torque converter lockup - fault code description ME | Pulse width modulation solenoid valve for torque converter lockup - fault code description ME |
| P2063 (P0748) | Modulating pressure control solenoid valve - fault code description ME | Modulating pressure control solenoid valve -fault code description ME |
| P2064 (P0748) | Shift pressure control solenoid valve - fault code description ME | Shift pressure control solenoid valve - fault code description ME |
| P2065 (P0702) | Supply voltage for valves - fault code description ME | Supply voltage for valves - fault code description ME |
| P2066 (P0715) | Supply voltage and function of rpm sensors - fault code description ME | Supply voltage and function of RPM sensors -fault code description ME |
| P2067 (P0705) | ETC control unit ME - fault code description Selector lever module wrongly coded |
ETC control unit, ME-SFI fault code description |
| P2068 (P0720) | ETC control unit ME - fault code description CAN message re wheel speed at rear from ESP control unit missing or faulty |
ETC control unit, ME-SFI fault code description |
| P2069 (P0700) | Engaged gear implausible or transmission leaky - fault code description ME | Gear implausible or leak in transmission, ME-SFI fault code description |
| P206A (P0700) | Command valve jams in the pressure position - fault code description ME | Command valve jams in pressure position, ME-SFI fault code description |
| P206B (P0740) | Torque converter lockup clutch - fault code description ME | Torque converter lockup clutch - fault code description ME |
| P206D (P0730) | Gear position comparison negative (on multiple occasions) - fault code description ME | Gear position comparison negative (on multiple occasions) - fault code description ME |
| P206E (-) | Transmission version implausible - fault code description ME Coded as having a manual transmission, vehicle has automatic gear selection |
Transmission variant implausible, ME-SFI fault code description |
| P206F (-) | Transmission version implausible - fault code description ME Wrongly coded or fault in CAN communication with ETC [EGS] control unit |
Transmission variant implausible, ME-SFI fault code description |
| P2070 (-) | Transmission version implausible - fault code description ME | Transmission variant implausible, ME-SFI fault code description |
| P2072 (P0450) | Tank pressure sensor ME - fault code description, Plausibility | Tank pressure sensor ME - fault code description |
| P2073 (-) | Electrical suction-type fan - fault code description, ME | Electric suction fan, ME-SFI fault code description |
| P2074 (-) | Variable intake manifold switchover valve - fault code description ME | Variable intake manifold switchover valve, ME-SFI fault code description |
| P2075 (P0442) | Purge control system has minor (very fine) leak (function chain) Fault code description ME |
Regeneration system leaking (causal chain) ME-SFI - fault code description |
| P2076 (-) | Oil sensor - fault code description, ME Oil temperature implausible |
Oil sensor, ME-SFI fault code description |
| P2079 (-) | CAN fault detection ME - fault code description Speed variable speed limiter |
CAN fault detection ME - fault code description |
| P207A (-) | CAN fault detection ME - fault code description Speed variable speed limiter |
CAN fault detection ME - fault code description |
| P207B (-) | CAN fault detection ME - fault code description, Selector lever position | CAN fault detection ME - fault code description |
| P207D (-) | EIS control unit - fault code description, ME | EIS control unit, ME-SFI fault code description |
| P207E (P0432) | Fault code description - left three-way catalytic converter effectiveness too low | Fault code description - three-way catalytic converter effectiveness too low |
| P207F (-) | Aging of left O2 sensor upstream of TWC - fault code description ME, correction parameter limit exceeded | Aging of O2 sensor upstream of TWC - fault code description ME |
| P2080 (P0153) | Aging of left O2 sensor upstream of TWC - fault code description ME, cycle duration | Aging of O2 sensor upstream of TWC - fault code description ME |
| P2081 (-) | Left O2 sensor downstream of TWC, signal - fault code description ME, no sensor condition change | O2 sensor signal - fault code description ME |
| P2082 (P0150) | Left O2 sensor upstream of TWC signal - fault code description ME, electrical fault | O2 sensor signal - fault code description ME |
| P2083 (P0156) | Left O2 sensor signal downstream of TWC - fault code description ME, electrical fault | O2 sensor signal - fault code description ME |
| P2085 (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME For the left cylinder bank, at partial load |
Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2086 (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME For the left cylinder bank, when idling |
Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2087 (-) | Self-adaptation of mixture formation at its limit - fault code description ME For the left cylinder bank, between idle and partial load |
Self-adaptation of mixture formation at its limit -fault code description ME-SFI |
| P2088 (P0155) | Left O2-sensor upstream of TWC heating - fault code description ME, internal resistance | O2-sensor heating - fault code description ME-SFI |
| P2089 (P0161) | Left O2-sensor downstream of TWC heating - fault code description ME, internal resistance | O2-sensor heating - fault code description ME-SFI |
| P208A (P0207) | Fault code description for fuel injection valves, ME, Cylinder 7 | Fault code description for fuel injection valves, ME-SFI |
| P208B (P0208) | Fault code description for fuel injection valves, ME, Cylinder 8 | Fault code description for fuel injection valves, ME-SFI |
| P208E (-) | Left bank of cylinders Cylinder shutoff valve - fault code description ME | AD07.61-P-4000-56BA |
| P208F (-) | Left bank of cylinders Cylinder shutoff valve - fault code description ME | AD07.61-P-4000-56BA |
| P2090 (-) | Connectors on O2 sensors wrong way round - fault code description ME | Sensor O2 cconnectors swapped, ME-SFI fault code description |
| P2091 (P0520) | Cylinder shutoff oil pressure sensor - fault code description ME | AD07.61-P-4000-58L |
| P2092 (-) | Right cylinder bank Cylinder shutoff valve - fault code description ME | AD07.61-P-4000-56BA |
| P2093 (-) | Right cylinder bank Cylinder shutoff valve - fault code description ME | AD07.61-P-4000-56BA |
| P2094 (-) | Cylinder shutoff valve does not open for cylinder shutoff ON - fault code description ME | AD07.61-P-4000-53BA |
| P2095 (-) | Cylinder shutoff (function chain) - fault code description ME Intake valve from cylinders 2, 3, 5 or 8 |
AD07.61-P-4000-54BA |
| P20A2 (-) | An inlet valve for cylinder is not operated at cylinder cutoff OFF- fault code description ME. | AD07.61-P-4000-55BA |
| P2097 (-) | Throttle valve actuator ME - fault code description Throttle valve jams, iced up |
Throttle valve actuator, ME-SFI fault code description |
| P2098 (-) | Crash signal implausible - fault code description, ME | Crash signal implausible, ME-SFI fault code description |
| P209B (-) | Exhaust flap switchover valve - fault code description ME | AD07.61-P-4000-57L |
| P209C (-) | Right cylinder bank Cylinder shutoff valve does not close for cylinder shutoff OFF - fault code description ME | AD07.61-P-4000-52BA |
| P209D (-) | Left cylinder bank Cylinder shutoff valve does not close for cylinder shutoff OFF - fault code description ME | AD07.61-P-4000-52BA |
| P209E (-) | Cylinder shutoff (function chain) - fault code description ME Exhaust valve on cylinder 5 |
AD07.61-P-4000-54BA |
| P209F (-) | Cylinder shutoff (function chain) - fault code description ME Exhaust valve on cylinder 2 |
AD07.61-P-4000-54BA |
| P20A0 (-) | Cylinder shutoff (function chain) - fault code description ME Exhaust valve on cylinder 3 |
AD07.61-P-4000-54BA |
| P20A1 (-) | Cylinder shutoff (function chain) - fault code description ME Exhaust valve on cylinder 5 8 |
AD07.61-P-4000-54BA |
| P20BE (P0135) | Right O2-sensor upstream of TWC heating - fault code description ME, voltage supply | O2-sensor heating - fault code description ME |
| P20BF (P0135) | Left O2-sensor upstream of TWC heating - fault code description ME, voltage supply | O2-sensor heating - fault code description ME |
| P20C2 (P0141) | Right O2-sensor downstream of TWC heating - fault code description ME, voltage supply | O2-sensor heating - fault code description ME |
| P20C3 (P0141) | Left O2-sensor downstream of TWC heating - fault code description ME, voltage supply | O2-sensor heating - fault code description ME |
| P20Ca (P0500) | CAN fault detection ME - fault code description Vehicle speed signal for left rear wheel from ESP control unit |
CAN fault detection ME - fault code description |
| P20Cb (P0500) | CAN fault detection ME - fault code description Vehicle speed signal for left front wheel from ESP control unit |
CAN fault detection ME - fault code description |
| P20CC (-) | CAN fault detection ME - fault code description CAN message from ESP control unit missing or faulty |
CAN fault detection ME - fault code description |
| P20CD (-) | Air conditioning - fault code description ME AC compressor torque implausible |
Air conditioning (AC) system, ME-SFI fault code description |
| P20CE (-) | Air conditioning - fault code description ME Refrigerant pressure in air conditioning too high |
Air conditioning (AC) system, ME-SFI fault code description |
| P20CF (P0120) | Fault code description for pedal value sensor, ME Voltage difference between signal 1 and signal 2 |
Pedal value sensor, ME-SFI fault code description |
| P20D0 (-) | Air conditioning - fault code description ME Air conditioning requests an implausible fan output. |
Air conditioning (AC) system, ME-SFI fault code description |
| P20D1 (-) | CAN fault detection ME - fault code description Torque request from DTR control unit implausible |
CAN fault detection ME - fault code description |
| P20D2 (-) | CAN fault detection ME - fault code description CAN transmission error of torque request from DTR control unit |
CAN fault detection ME - fault code description |
| P20D3 (-) | CAN fault detection ME - fault code description CAN transmission error of torque request from DTR control unit |
CAN fault detection ME - fault code description |
| P20D4 (-) | Load limitation active - fault code description ME | Active load limitation, ME-SFI fault code description |
| P20D5 (P0702) | ETC control unit ME - fault code description The torque request from the EGS control unit is implausible |
ETC control unit, ME-SFI fault code description |
| P20D6 (P0702) | ETC control unit ME - fault code description CAN transmission error of torque request from ETC [EGS] control unit |
ETC control unit, ME-SFI fault code description |
| P20D7 (P0702) | ETC control unit ME - fault code description CAN transmission error of torque request from ETC [EGS] control unit |
ETC control unit, ME-SFI fault code description |
| P20D8 (-) | ESP control unit - fault code description, ME | ESP control unit, ME-SFI fault code description |
| P20D9 (-) | CAN fault detection ME - fault code description Torque request from ESP control unit implausible |
CAN fault detection ME - fault code description |
| P20Da (-) | CAN fault detection ME - fault code description CAN transmission error of torque request from ESP control unit |
CAN fault detection ME - fault code description |
| P20Db (-) | CAN fault detection ME - fault code description CAN transmission error of torque request from ESP control unit |
CAN fault detection ME - fault code description |
| P20DC (P0120) | Fault code description for pedal value sensor, ME Open circuit on signal path 1 |
Pedal value sensor, ME-SFI fault code description |
| P20DD (P0120) | Fault code description for pedal value sensor, ME Short circuit at signal path 1 |
Pedal value sensor, ME-SFI fault code description |
| P20DE (P0120) | Fault code description for pedal value sensor, ME Open circuit on signal path 2 |
Pedal value sensor, ME-SFI fault code description |
| P20DF (P0120) | Fault code description for pedal value sensor, ME Short circuit at signal path 2 |
Pedal value sensor, ME-SFI fault code description |
| P20E3 (P0120) | Fault code description for pedal value sensor, ME, voltage supply | Pedal value sensor, ME-SFI fault code description |
| P20E4 (-) | CAN fault detection ME - fault code description Implausible signal from stop lamp switch |
CAN fault detection ME - fault code description |
| P20E5 (-) | CAN fault detection ME - fault code description CAN transmission error of signal from stop lamp switch |
CAN fault detection ME - fault code description |
| P20E6 (-) | CAN fault detection ME - fault code description CAN transmission error of signal from stop lamp switch |
CAN fault detection ME - fault code description |