Section 196 (General Orphan Data (2 Of 2))
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW X2, 2022 BMW X2, 2021 BMW X2, 2020 BMW X2, and 2019 BMW X2. However, it is still accessible from the selected car via links, so may be relevant.
- Frequently asked questions about surface protection
- Converting the production date
- Calculating the expiration date
- Determining the date of the next brake fluid service
- If necessary: Replacing the gas pressure springs for hood
- Partially removing left output shaft
- Safety instructions and general information
- Release the charge air line from the intake system
- Fasten the charge air line to the intake system
- Removing the gutter strip on the right of the windscreen
- Removing side panel sealing
- Installing side panel sealing
- Installing the gutter strip, right on the windscreen
- Remove door lock
- Preserving the front door
- Install the door lock
- Removing the crash pad
- Remove rear power window regulator
- Remove the rear outer door handle support
- Preserving the rear door
- Installing the rear outside door handle support
- Installing rear power window regulator
- Installing the crash pad
- Remove the actuator on the hood hinge
- Install the actuator on the hood hinge
- Remove rear window
- Remove right rear wheel arch cover
- Install the filler tube on the active tank
- Installing the rear wheel arch cover on the right
- Remove the side trim
- Install trim at side
- Release washer fluid reservoir
- Fasten the washer fluid reservoir
- Partially removing the rear wheel arch trim
- Partly installing the rear wheel arch trim
- Required new parts/consumables
- Installing all grab handles
- Releasing the rear headlining
- Attaching the rear headlining
- Installing side airbag in front seat
- Installing the support for seat adjustment switch combination
- Installing the seat cover for the front seat (Sport)
- Cutting to length and stripping insulation from cables
- Register battery change
- Removing the outer cover on the electrical front seat
- Installing the outer cover on the electrical front seat
- If installed: Removing shift paddle for automatic transmission
- Removing the cover for sports steering wheel
- Installing cover for the sport steering wheel
- If installed: Installing the shift paddle for the automatic transmission
- Overview, rain sensor (additional work when replacing the windshield/sensor replacement)
- Initializing rain, light and solar sensor
- Removing trim from water channel on right
- Installing trim in water channel on right
- Removing the compact spare wheel
- Installing the mirror glass
- Checking the installation position of the drive for the exterior mirror adjustment
- Safety regulations for handling components with gas generators
- Installing side trim panel for the left and right center console
- Replace the DME control unit
- Releasing the oil drain plug
- Tightening the oil drain plug
- For replacement: Reset adaptation values
- Putting the fuel pump control electronics into operation
- Removing the rear connecting supports
- Installing the rear connecting supports
- Suction the air conditioning
- Evacuating the air conditioning
- Filling the air conditioning
- Universal gearbox holder
- Remove cross connection
- Install cross connection
- Teaching in end stop software for electric steering gear (EPS)
- Preparing the brake test
- Releasing the front wheel arch cover
- Partially installing the front wheel arch cover
- Commissioning or bedding in (brake) of new brake pads and discs (high brake)
- Installing the front wheel arch cover
- Electromechanical parking brake start-up after emergency release
- DSC unit start-up/driving dynamics sensor adjustment
- Prepare the removal of the EMF actuator
- After EMF actuator replacement: putting electromechanical holding brake into operation
- Program/encode the optional equipment system (SAS)
- Perform the CBS reset
- If installed: Checking the gas pressure springs for hood (only for versions with active pedestrian protection (SA8TR))
- Remove front left wheel
- Install the locating pins
- Attaching the front left wheel
- Remove the locating pins
- Installing the engine block on the assembly jig
- Remove exhaust turbocharger
- Installing exhaust turbocharger
- Observing the hardening time of the screw locking agent on the screw plug
- Partially removing right output shaft
- Partially installing right output shaft
- Removing the catalytic converter (engine removed)
- Installing the catalytic converter (engine removed)
- Version with eccentric shaft servomotor: Teaching in the end stops with the diagnostic system
- Remove air conditioning compressor
- Installing air conditioning compressor
- If Installed: Remove the right brake air duct
- If installed: Install the right brake air duct
- Removing heat shield at upper exhaust turbocharger
- Install the heat shield on the exhaust turbocharger, top
- Removing sealing side panel
- Removing the jet chain partially
- Removing the gas pressure spring for engine compartment lid
- Installing the gas pressure spring for engine compartment lid
- Installing jet chain partially
- When replacing the spindle drive
- Removing windscreen wiper arm of the rear wiper
- Installing wiper arm of the rear wiper
- Disconnect the plug connection on the rain-light-solar-condensation sensor
- Connecting connector to the rain-light-solar-condensation sensor
- Calibrate KAFAS camera
- Installing the holder on left or right
- Remove the right A-pillar trim panel
- Install the right A-pillar trim panel
- Removing the front seats on the left and right
- Removing the speaker trim from the left and right center bass
- Removing the left and right B-pillar trim panels at bottom
- Install the left and right B-pillar trim panels at bottom
- Installing the speaker trim on the left and right center bass
- Installing the gearshift lever cover
- Install the left and right front seat
- Removing seat angle adjustment lever on front seat
- Installing lever for seat angle adjustment on front seat
- Remove side airbag from front seat
- Install side airbag on front seat
- Removing the side airbag on the front seat (electric seat)
- Installing the side airbag on the front seat (electric seat)
- Removing the seat cover together with the cushion
- Removing the seat cover with the cushion
- Removing the guide sleeve for the rear head restraint
- Installing the guide sleeve for the rear head restraint
- Removing both front head restraints
- Check the roller sunblind and the glass roof for function
- Installing both front head restraints
- Removing all wheels
- Installing all wheels
- Processing the LED headlight service test module
- Removing the left footwell ventilation duct
- Installing the left footwell ventilation duct
- Removing side trim panel for the left center console
- Installing side trim panel for the left center console
- Remove the side panel on the right instrument panel
- Removing right footwell ventilation duct
- Installing right footwell ventilation duct
- Install the side panel on instrument panel on the right
- Enter the installation position of the damper motor
- Removing the side trim panel for the right center console
- Installing the side trim panel for the right center console
- Addressing the controller drive
- Adjusting headlights
- Remove front right wheel
- Installing the front right wheel
- Removing the system battery partially
- Installing the system battery partially
- Removing bottom right C-pillar trim panel
- Install the C-pillar trim panel at the bottom right
- Removing trim of the audio operating unit
- For equipment specification with air duct for rear passenger compartment: Remove the air duct
- For equipment specification with air duct for rear passenger compartment: Install air duct
- Deactivating the 48 V electrical system
- Activating the 48 V electrical system
- Partially remove the front right wheel arch cover
- Partially installing the front right wheel arch trim
- Initializing the power windows
- When replacing the alternator/alternator regulator: Reset generator statistical data
- Reset ultra-small quantity adaptation
- Remove the ignition coil of the first cylinder
- Install the ignition coil of the first cylinder
- Check the coolant level and top up if applicable
- Replacement: Adjusting the exhaust gas pressure sensor
- Disconnecting the delivery unit
- Connect delivery unit
- Removing the left and right tank covers
- Installing the left and right tank covers
- Opening the locking ring
- Close the locking ring
- Removing the front right wheel arch cover
- Installing the front right wheel arch cover
- Fill and vent the coolant circuit
- Install front cross connection (air duct removed)
- Partially removing the front wheel arch trim
- Partially removing the front wheel arch cover
- Partially install the front wheel arch cover
- Partly install the front wheel arch trim
- Remove front cross connection (air duct removed)
- Removing the front connecting supports
- Installing the front connecting support
- When replacing the gasoline particulate filter: Register the gasoline particulate filter
- Remove the filling hose of the washing liquid container
- Inserting filling hose of the washer fluid reservoir
- Removing the front underbody protection
- Removing holder with rubber mount
- Installing holder with rubber mount
- Installing the front underbody protection
- Removing intermediate shaft with support tube
- Installing intermediate shaft with support tube
- If installed: Removing rear underbody protection
- If installed: Installing underbody protection at rear
- Removing the front left and right wheels
- Installing the front left and right wheels
- Commissioning/bedding in (brake) new brake pads and brake discs
- Removing the rear left and right wheels
- Install the rear left and right wheels
- Start-up or bedding in break-in of new brake pads and blades (rear brake)
- Connecting the bleeder unit for brake fluid (after repair, top up brake fluid)
- Remove the 12 V power socket mount
- Install the mount of the 12-V socket in the rear
- Install brake pedal tensioner
- Remove the brake pedal tensioner
- DSC unit start-up/driving dynamics sensor adjustment/control unit programming
- Partly loosening the wheel arch cover in front
- Removing the rear right wheel
- Removing the cover on the inside mirror