Engine Mechanical - 2.7L V6 BITURBO - APB, Bel

• Technical data
  • VIN number
  • Engine data
• Engine - Assembly
  • Engine, removing and installing
    • Notes
    • Engine, removing and installing
      • Special tools and equipment
    • Engine, removing
      • Notes
      • All models
    • Engine, attaching to engine stand
    • Engine, installing
    • Tightening torques
      • Notes
      • Manual transmission
      • Automatic transmission
    • Vacuum Hose Diagram(S)
      • Notes
      • Vehicles without Secondary Air Injection (AIR)
      • Vehicles with Secondary Air Injection (AIR)
    • Vacuum layout - partial systems
      • Air flow diagram (general)
      • Charge air pressure control system
      • Fuel tank breather system (EVAP system)
      • Air diversion system (air "recirculation" on overrun)
      • Crankcase breather system
      • Suction jet pump (vehicles with automatic transmission)
    • Installation position, overview
• Engine - Crankshaft, Cylinder block
  • Engine crankshaft/crankcase, disassembly and assembly
    • Ribbed belt, removing and installing
      • Removing
      • Installing
    • Toothed belt, removing and installing
      • Removing
      • Installing
    • Vibration damper, removing and installing
    • Cylinder block, crankshaft and flywheel, disassembling and assembling
    • Crankshaft bearing caps, installing
      • Notes
      • Tightening sequence
    • Axial and radial clearance of crankshaft, measuring
      • Axial clearance
      • Radial clearance
    • Crankshaft oil seals, replacing
      • A - Toothed belt end
      • B - Flywheel end
      • Vehicles with manual transmission
      • Installing
      • Vehicles with automatic transmission
    • Dual-mass flywheel/drive plate; installation dimensions, removing and installing
      • Notes
      • A - Flywheel
        • Removing
        • Installing
      • B - Drive plate
        • Removing
        • Installing
    • Needle bearing in dual-mass flywheel, removing and installing
    • Pistons and piston rings, checking
      • Pistons
      • Checking piston diameter
      • Ring-to-groove clearnce
      • Checking piston ring gap
    • Cylinder bores, checking
      • Notes
      • Piston and cylinder dimensions
    • Connecting rods, connecting rod bearings, checking
      • Notes
      • Checking radial clearance
• Engine - Cylinder head, Valvetrain
  • Valve gear, servicing
    • Notes
    • Sealing end points of joints between bearing caps and cylinder head
    • Oil seals in cylinder heads, replacing
      • Oil seal for camshaft drive (left and right cylinder heads)
      • Oil seal at Hall sensor (right cylinder head)
        • Notes
        • Installing
      • Removing oil seal at Hall sensor (left cylinder head)
        • Notes
        • Installing
      • Rear oil seal and sealing flange (left cylinder head)
        • Notes
        • Installing
    • Cylinder head covers, removing and installing
      • Removing and installing left cylinder head cover
        • Removing
        • Installing
      • Right cylinder head cover, removing and installing
        • Removing
        • Installing
    • Cylinder head, removing and installing
      • Removing and installing left cylinder head
      • Removing
      • Installing
      • Tightening torques
      • Right cylinder head, removing and installing
    • Cylinder head, checking for distortion
    • Cylinder head, reworking
    • Compression, checking
      • Test requirements
      • Procedure
      • Compression pressure values
      • Installing
      • Tightening torques
    • Sealing cap (core plug) in cylinder head, installing
    • Camshaft adjustment function, checking
      • Special tools and equipment
      • Test requirement
      • Test sequence
    • Solenoid valve for camshaft adjustment, checking
      • Special tools and equipment
      • Checking
      • Checking internal resistance
      • Checking voltage supply
      • Checking activation
    • Camshafts and camshaft adjusters, removing and installing
      • Removing
      • Left cylinder head
      • Right cylinder head
      • All:
      • Installing
      • Tightening torques
    • Camshaft axial clearance, checking
    • Valve dimensions
    • Hydraulic valve lifters, checking
    • Valve stem seals, replacing
      • Notes
      • Exhaust side
      • Inlet side
      • Reworking valves
    • Valve guides, checking
      • Notes
      • Wear limit
    • Valve seats, reworking (refacing)
      • Notes
      • Calculating maximum permissible reworking dimension
• Engine - Lubrication
  • Lubrication system components, removing and installing
    • Notes
    • Crankcase breather and oil spray jets
      • Notes
      • Securing tensioner in position before removing
    • Oil pump, oil pan, oil filter and oil cooler, removing and installing
    • Oil check valves, replacing
      • Notes
      • Removing
      • Installing
    • Lower section of oil pan, removing and installing
      • Special tools, testers and auxiliary items
      • Removing
      • Installing
    • Chain tensioner for oil pump, checking
      • Removing
      • Installing
    • Upper and lower sections of oil pan, removing and installing
      • Special tools and equipment
      • Removing
      • Installing:
      • Tightening torques
    • Oil pump, removing and installing
      • Removing
      • Installing
      • Tightening torques
    • Front sealing flange and oil pump drive chain, removing and installing
      • Removing
      • Replacing oil pump drive chain
      • Installing
    • Chain sprocket for oil pump on crankshaft, removing and installing
      • Removing
      • Installing
    • Crankshaft oil seal - pulley end, replacing
      • Removing
      • Installing
    • Oil pressure and oil pressure switch, checking
      • Test procedure
    • Engine oil
      • Notes
      • Viscosity grades and oil specifications
    • Oil level, checking
      • Test conditions
      • Test sequence