Section 4 (Manual Transmission - TREMEC 6-Speed)
WARNING: This page is about a different variant/trim than selected.
- Specifications
- Schematic and Routing Diagrams
- Visual Identification
- Diagnostic Information and Procedures
- Diagnostic Code Index
- DTC P0502 or P0503
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC P0712 or P0713
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC P0801
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- Repair Verification
- DTC P0806
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC P0807 or P0808
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Typical Scan Tool Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC P080A
- DTC P080C or P080D
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- Repair Verification
- Clutch Pedal Position Sensor Learn
- Symptoms - Manual Transmission
- Transmission Shifts Hard
- Transmission Gear Clash When Shifting Gears
- Transmission Noisy
- Transmission Jumps Out of Gear
- Transmission Does Not Shift into One Gear
- Transmission Locked in One Gear
- Transmission Clunk on Acceleration or Deceleration
- Transmission Fluid Leak Diagnosis
- Repair Instructions - On Vehicle
- Transmission Fluid Level Inspection
- Transmission Mount Inspection
- Transmission Rear Mount Replacement
- Shift Control Assembly Replacement
- Transmission Control Lever Knob Replacement
- Main Shaft Rear Seal Replacement
- Backup Lamp Switch Replacement
- Transmission Fluid Temperature Sensor Replacement
- Vehicle Speed Sensor Replacement
- Reverse Lockout Solenoid Replacement
- Gear Select/Skip Shift Solenoid Replacement
- Transmission Fluid Replacement
- Transmission Replacement
- Repair Instructions - Off Vehicle
- Transmission Disassemble
- Main Shaft and Input Shaft Disassemble
- Counter Gear Shaft Disassemble
- Synchronizers Disassemble
- Synchronizers Cleaning and Inspection
- Synchronizers Assemble
- Shift Shaft and Fork Assemblies Disassemble
- Shift Shaft and Fork Assemblies Cleaning and Inspection
- Shift Shaft and Fork Assemblies Assemble
- Transmission Case and Clutch Housing Disassemble
- Transmission Case and Clutch Housing Cleaning and Inspection
- Transmission Case and Clutch Housing Assemble
- Shift Control Shaft Cover Assembly Disassemble
- Shift Control Shaft Cover Assembly Assemble
- Extension Disassemble
- Extension Cleaning and Inspection
- Extension Assemble
- Bearings and Spacers Cleaning and Inspection
- Gears Cleaning and Inspection
- Counter Gear Shaft Assemble
- Main Shaft and Input Shaft Assemble
- Transmission Assemble
- Shimming Procedures
- Description and Operation
- Special Tools and Equipment