Section 3 (Engine Mechanical - 2.0L)
WARNING: This page is about a different variant/trim than selected.
- Specifications
- Fastener Tightening Specifications
- Engine Mechanical Specifications
- Sealers, Adhesives, and Lubricants
- Thread Repair Specifications
- Engine Block - Front View
- Engine Block - Back View
- Engine Block - Left Side View
- Engine Block - Bottom View
- Engine Block - Right Side View
- Engine Block - Top View
- Lower Crankcase - Front View
- Lower Crankcase - Back View
- Lower Crankcase - Bottom View
- Lower Crankcase - Left View
- Lower Crankcase - Right View
- Cylinder Head - Top View
- Cylinder Head - Intake Manifold Deck View
- Cylinder Head - Exhaust Manifold Deck View
- Cylinder Head - Front View
- Cylinder Head - Back View
- Cylinder Head - Bottom View
- Component Locator
- Diagnostic Information and Procedures
- Diagnostic Starting Point - Engine Mechanical
- Symptoms - Engine Mechanical
- Base Engine Misfire without Internal Engine Noises
- Base Engine Misfire with Abnormal Internal Lower Engine Noises
- Base Engine Misfire with Abnormal Valve Train Noise
- Base Engine Misfire with Coolant Consumption
- Base Engine Misfire with Excessive Oil Consumption
- Engine Noise on Start-Up, but Only Lasting a Few Seconds
- Upper Engine Noise, Regardless of Engine Speed
- Lower Engine Noise, Regardless of Engine Speed
- Engine Noise Under Load
- Engine Will Not Crank - Crankshaft Will Not Rotate
- Coolant in Combustion Chamber
- Coolant in Engine Oil
- Engine Compression Test
- Cylinder Leakage Test
- Oil Consumption Diagnosis
- Oil Pressure Diagnosis and Testing
- Oil Leak Diagnosis
- Crankcase Ventilation System Inspection/Diagnosis
- Drive Belt Chirping Diagnosis
- Drive Belt Squeal Diagnosis
- Drive Belt Whine Diagnosis
- Drive Belt Rumbling Diagnosis
- Drive Belt Vibration Diagnosis
- Drive Belt Falls Off Diagnosis
- Drive Belt Excessive Wear Diagnosis
- Drive Belt Tensioner Diagnosis
- Repair Instructions
- On-Vehicle Repair Instructions
- Upper Intake Manifold Sight Shield Replacement
- Drive Belt Replacement
- Drive Belt Tensioner Replacement - Supercharger
- Engine Mount Inspection
- Engine Oil Pressure Sensor and/or Switch Replacement
- Powertrain Mount Balance Procedure - Total Mount
- Powertrain Mount Balance Procedure - Lower Mount
- Engine Mount Bracket Replacement
- Engine Mount Replacement
- Engine Support Fixture
- Oil Level Indicator and Tube Replacement
- Crankcase Ventilation Hoses/Pipes Replacement
- Supercharger Replacement
- Intake Manifold Replacement
- Crankshaft Balancer Replacement
- Crankshaft Front Oil Seal Replacement
- Engine Front Cover Replacement
- Timing Chain, Sprockets, and/or Tensioner Replacement
- Camshaft Cover Replacement
- Intake Camshaft and Lifter Replacement
- Exhaust Camshaft and Lifter Replacement
- Valve Stem Oil Seal and Valve Spring Replacement
- Cylinder Head Replacement
- Oil Cooler Replacement
- Oil Pan Replacement
- Crankshaft Rear Oil Seal Replacement
- Engine Flywheel Replacement
- Engine Replacement
- Engine Oil and Oil Filter Replacement
- Off-Vehicle Repair Instructions
- Draining Fluids and Oil Filter Removal
- Crankshaft Balancer Removal
- Engine Flywheel Removal
- Oil Level Indicator and Tube Removal
- Oil Cooler Removal
- Exhaust Manifold Removal
- Supercharger Removal
- Intake Manifold Removal
- Camshaft Cover Removal
- Camshaft Position Sensor Housing Removal
- Engine Front Cover and Oil Pump Removal
- Timing Chain and Tensioner Removal
- Intake Camshaft, Follower, and Adjuster Removal
- Exhaust Camshaft, Follower, and Adjuster Removal
- Balance Shaft Drive Chain and Tensioner Removal
- Balance Shaft Removal
- Water Pump Removal
- Cylinder Head Removal
- Oil Pan Removal
- Piston, Connecting Rod, and Bearing Removal
- Lower Crankcase Removal
- Crankshaft and Bearings Removal
- Engine Block Disassemble
- Engine Block Cleaning and Inspection
- Cylinder Honing
- Cylinder Sleeve Removal
- Cylinder Sleeve Installation
- Crankshaft Balancer Cleaning and Inspection
- Engine Flywheel Cleaning and Inspection
- Crankshaft and Bearings Cleaning and Inspection
- Piston and Connecting Rod Disassemble
- Piston, Connecting Rod, and Bearings Cleaning and Inspection
- Piston and Connecting Rod Assemble
- Camshaft Cleaning and Inspection
- Timing Chain and Sprockets Cleaning and Inspection
- Balance Shaft Cleaning and Inspection
- Balance Shaft Drive Chain and Sprockets Cleaning and Inspection
- Cylinder Head Disassemble
- Cylinder Head Cleaning and Inspection
- Cylinder Head Assemble
- Oil Pump Disassemble
- Oil Pump Assemble
- Intake Manifold Cleaning and Inspection
- Exhaust Manifold Cleaning and Inspection
- Oil Pan Cleaning and Inspection
- Thread Repair
- Service Prior to Assembly
- Engine Block Assemble
- Crankshaft and Bearings Installation
- Lower Crankcase Installation
- Crankshaft Rear Oil Seal Installation
- Piston, Connecting Rod, and Bearing Installation
- Cylinder Head Installation
- Intake Camshaft, Follower, and Adjuster Install
- Exhaust Camshaft, Follower, and Adjuster Install
- Balance Shaft Installation
- Water Pump Installation
- Timing Balance Shafts to Engine
- Balance Shaft Drive Chain and Tensioner Install
- Timing Chain, Sprockets, Tensioner Installation
- Crankshaft Front Oil Seal Installation
- Engine Front Cover and Oil Pump Installation
- Camshaft Position Sensor Housing Installation
- Camshaft Cover Installation
- Oil Pan Installation
- Crankshaft Balancer Installation
- Oil Filter Adapter Installation
- Intake Manifold Installation
- Supercharger Installation
- Exhaust Manifold Installation
- Oil Cooler Installation
- Oil Level Indicator and Tube Installation
- Engine Flywheel Installation
- Engine Prelubing
- On-Vehicle Repair Instructions
- Description and Operation
- Special Tools and Equipment