Section 44 (Automatic Transmission - 8L45 - Repair Instructions - Off Vehicle)
WARNING: This page is about a different variant/trim than selected.
- Repair Instructions - Off Vehicle
- Torque Converter Removal and Holding Fixture Installation
- Transmission Fluid Pan and Filter Assembly Removal
- Control Valve Assembly and Transmission Wiring Harness Removal
- Transmission Case Front Cover and Drive Link Removal
- Stator Shaft Support Removal
- 1-3-5-6-7 Clutch Assembly Removal
- 2-3-4-6-8 and 4-5-6-7-8 Reverse Clutch Assembly Removal
- Direct Overdrive Internal Gear, Direct Overdrive Carrier, Input Internal Gear, and Input Carrier Assembly Removal
- 1-2-7-8 Reverse Clutch Piston Removal
- 1-2-7-8 Reverse Clutch Plate Assembly and Input Sun Gear Assembly Removal
- Reaction Internal Gear and 1-2-3-4-5 Reverse Hub and 1-2-3-4-5 Reverse Clutch Plate Assembly Removal
- Reaction Carrier Assembly, Output Carrier, and Output Shaft Removal
- Propeller Shaft Transmission Flange Removal (Rear Wheel Drive)
- Case Extension Assembly Removal
- Manual Shift Detent Lever with Shaft Position Switch Assembly and Park Pawl Actuator Removal
- Manual Shift Shaft Seal Removal
- Transmission Case Cleaning and Inspection
- Manual Shift Shaft Seal Installation
- Manual Shift Detent Lever with Shaft Position Switch Assembly and Park Pawl Actuator Installation
- Case Extension Disassemble (8L90)
- Case Extension Disassemble (8L45)
- Propeller Shaft Transmission Flange Fluid Seal Removal (8L45)
- Propeller Shaft Transmission Flange Fluid Seal Installation (8L90)
- Propeller Shaft Transmission Flange Fluid Seal Installation (8L45)
- Case Extension Assemble (8L90)
- Case Extension Assemble (8L45)
- Case Extension Assembly Installation
- Propeller Shaft Transmission Flange Installation (Rear Wheel Drive)
- Reaction Carrier Overhaul
- Reaction Carrier Assembly, Output Carrier, and Output Shaft Installation
- Reaction Internal Gear and 1-2-3-4-5 Reverse Hub Overhaul
- Reaction Internal Gear and 1-2-3-4-5 Reverse Hub and 1-2-3-4-5 Reverse Clutch Plate Assembly Installation
- 1-2-3-4-5 Reverse Clutch Backing Plate Retaining Ring Measurement
- Input Sun Gear Overhaul
- 1-2-7-8 Reverse Clutch Plate Assembly and Input Sun Gear Assembly Installation
- 1-2-7-8 Reverse Clutch Piston Installation
- Direct Overdrive Internal Gear Overhaul
- Input Internal Gear Overhaul
- Input Carrier Overhaul
- Input Carrier Assembly Installation
- 2-3-4-6-8 and 4-5-6-7-8 Reverse Clutch Disassemble
- 2-3-4-6-8 and 4-5-6-7-8 Reverse Clutch Assemble (8L90)
- 2-3-4-6-8 and 4-5-6-7-8 Reverse Clutch Assemble (8L45)
- 2-3-4-6-8 Clutch Backing Plate Retaining Ring Measurement (8L90)
- 2-3-4-6-8 Clutch Backing Plate Retaining Ring Measurement (8L45)
- 4-5-6-7-8 Reverse Clutch Backing Plate Retaining Ring Measurement (8L90)
- 4-5-6-7-8 Reverse Clutch Backing Plate Retaining Ring Measurement (8L45)
- Direct Overdrive Carrier, Input Internal Gear, and 2-3-4-6-8 and 4-5-6-7-8 Reverse Clutch Assemble
- 2-3-4-6-8 and 4-5-6-7-8 Reverse Clutch Assembly Installation
- 1-3-5-6-7 Clutch Disassemble
- 1-3-5-6-7 Clutch Assemble (8L90)
- 1-3-5-6-7 Clutch Assemble (8L45)
- 1-3-5-6-7 Clutch Backing Plate Retaining Ring Measurement
- 1-3-5-6-7 Clutch Assembly Installation
- Stator Shaft Support Disassemble
- Stator Shaft Support Assemble (8L90)
- Stator Shaft Support Assemble (8L45)
- Stator Shaft Support Installation
- Transmission End Play Check
- Torque Converter Fluid Seal Removal
- Torque Converter Fluid Seal Installation
- Transmission Case Front Cover and Drive Link Installation
- Control Valve Body Assembly Disassemble
- Control Valve Solenoid Body Cleaning and Inspection
- Control Valve Upper Body Assembly Cleaning and Inspection
- Control Valve Body Assembly Assemble
- Control Valve Assembly and Transmission Wiring Harness Installation
- Transmission Fluid Pan and Filter Assembly Installation
- Torque Converter Installation and Holding Fixture Removal