LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2023 >> Camaro ZL1, 2D Convertible, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 44 (Automatic Transmission - 8L45 - Repair Instructions - Off Vehicle) >> Repair Instructions - Off Vehicle >> Control Valve Assembly and Transmission Wiring Harness Installation >> Special Tools

Special Tools

WARNING: This page is about a different variant/trim than selected.

DT-45053  Universal Clamp Press

Equivalent regional tools: Special Tools

  1. Fig 1: Exploded View Of Control Valve Body Assembly With Tightening Sequence
    GM3977955Courtesy of GENERAL MOTORS COMPANY

    Clutch Housing Fluid Passage Seal (1) - Install NEW

    2. CAUTION:

    The intermediate and output speed sensors must be installed in the correct location. Harsh shifting or transmission damage may occur if the speed sensors are not installed in the correct location.

  2. Install the automatic transmission output speed sensor wiring harness (2).Speed sensors must be in the positions indicated by arrow.
    3. CAUTION:

    This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.

    CAUTION:

    Refer to Fastener Caution .

  3. Automatic Transmission Case Front Cover Bolt (3) - Install NEW and tighten M6 x 25 [3x]
    1. First Pass: 4 N.m (35 lb in)
    2. Final Pass: 45 degrees
    4. CAUTION:

    Use care when handling the control valve body assembly. If dropped, damage to the control solenoid valve body assembly internal components may result.

  4. Control Valve Body Assembly (4) - Install
  5. Control Valve Solenoid Body Bolt (5) - Install and tighten in sequence M6 x 68 [7x] 9 N.m (80 lb in)
  6. Control Valve Solenoid Body Bolt (6) - Install and tighten in sequence M6 x 45 [4x] 9 N.m (80 lb in)
  7. Manual Shift Detent Lever Spring (7) - Install
  8. Manual Shift Detent Lever Spring Bolt (8) - Install and tighten M6 x 2512 N.m (106 lb in)
  9. Manual Valve (9) - Connect
  10. Electrical Connector@Automatic Transmission Wiring Harness (10) - Connect
  11. Electrical Connector@Automatic Transmission Control Wiring Harness (11) - Connect
  12. GM3977873Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Ensure the driven sprocket locking tab is in the unlocked position before installing the sprocket.

    The driven sprocket (3) locking tab is located on the back of the sprocket and faces the pump.

  13. Install the drive link (chain) to the driven sprocket (3) and then install the driven sprocket (3) to the oil pump shaft.
  14. Rotate the sprocket as shown and push down on the tab until it locks the driven sprocket (3) in place.
  15. Automatic Transmission Fluid Baffle (2) - Install
    16. CAUTION:

    This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.

  16. Automatic Transmission Fluid Baffle Bolt (3) - Install NEW and tighten M6 x 25 [2x]
    1. First Pass: 4 N.m (35 lb in)
    2. Final Pass: 45 degrees
scientia non olet · About LEMON Manuals