Section 40 (Automatic Transmission - 10L60, 10L80 Or 10L90 - Repair Instructions - Off Vehicle)
WARNING: This page is about a different variant/trim than selected.
- Repair Instructions - Off Vehicle
- Transmission Housing Sound Insulator Removal
- Transmission Housing Sound Insulator Removal (10L60)
- Torque Converter Removal and Holding Fixture Installation
- Propeller Shaft Transmission Flange Removal
- Case Extension Assembly Removal
- Transmission Fluid Pan and Filter Assembly Removal
- Control Valve Assembly and Transmission Wiring Harness Removal
- Transmission Fluid Pump Removal
- Automatic Transmission Case Front Cover Removal
- Rotating Clutch, Gear, and Shaft Shell Assembly Removal
- Rotating Clutch, Gear, and Shaft Shell Assembly Removal (10L60)
- Output Carrier Assembly and Output Carrier Thrust Bearings Removal
- Manual Shift Detent Lever with Shaft Position Switch Assembly and Park Pawl Actuator Removal
- Manual Shift Shaft Seal Removal
- Automatic Transmission Case Hole Plug Removal
- Transmission Case Cleaning and Inspection
- Automatic Transmission Case Hole Plug Installation
- Case Extension Disassemble
- Case Extension Assemble
- Manual Shift Shaft Seal Installation
- Manual Shift Detent Lever with Shaft Position Switch Assembly and Park Pawl Actuator Installation
- Output Carrier Assembly and Output Carrier Thrust Bearings Installation
- Rotating Clutch, Gear, and Shaft Shell Assembly Disassemble
- Rotating Clutch, Gear, and Shaft Shell Assembly Disassemble (10L60)
- Direct Overdrive Sun Gear Shaft Disassemble
- Direct Overdrive Sun Gear Shaft Assemble
- Direct Overdrive Sun Gear Shaft Assemble (10L60)
- Triple Clutch Housing Disassemble (10L90)
- Triple Clutch Housing Disassemble (10L80)
- Triple Clutch Housing Disassemble (10L60)
- Triple Clutch Housing Assemble (10L90)
- Triple Clutch Housing Assemble (10L80)
- Triple Clutch Housing Assemble (10L60)
- 2-3-4-5-7-9-10 Clutch Backing Plate Retaining Ring Measurement
- 1-2-3-4-6-7-8-10-Reverse Clutch Backing Plate Retaining Ring Measurement
- 4-5-6-7-8-9-10-Reverse Clutch Backing Plate Retaining Ring Measurement
- 1-3-5-6-7-8-9 Clutch Hub and Output Sun Gear Disassemble
- 1-3-5-6-7-8-9 Clutch Hub and Output Sun Gear Disassemble (10L60)
- Turbine Shaft Seal Removal
- Turbine Shaft Seal Installation
- Turbine Shaft Seal Installation (10L60)
- 1-3-5-6-7-8-9 Clutch Hub and Output Sun Gear Assemble
- 1-3-5-6-7-8-9 Clutch Hub and Output Sun Gear Assemble (10L60)
- 1-3-5-6-7-8-9 Clutch Backing Plate Measurement
- Rotating Clutch, Gear, and Shaft Shell Assembly Assemble
- Rotating Clutch, Gear, and Shaft Shell Assembly Assemble (10L60)
- Rotating Clutch, Gear, and Shaft Shell Assembly Installation
- Rotating Clutch, Gear, and Shaft Shell Assembly Installation (10L60)
- Front End Play Check
- Front End Play Check (10L60)
- 1-2-3-4-5-6-Reverse Clutch Apply Plate Measurement
- 1-2-3-4-5-6-Reverse Clutch Apply Plate Measurement (10L60)
- Automatic Transmission Case Front Cover Disassemble
- Automatic Transmission Case Front Cover Disassemble (10L60)
- Automatic Transmission Case Front Cover Assemble
- Automatic Transmission Case Front Cover Assemble (10L60)
- 1-2-8-9-10-Reverse Clutch Backing Plate Retaining Ring Measurement
- Automatic Transmission Case Front Cover Installation
- Automatic Transmission Fluid Pump Driven Gear Removal
- Automatic Transmission Fluid Pump Driven Gear Installation
- Automatic Transmission Fluid Pump Installation
- Control Valve Assembly Disassemble
- Control Valve Assembly Assemble
- Control Valve Assembly and Transmission Wiring Harness Installation
- Transmission Fluid Pan and Filter Assembly Installation
- Case Extension Assembly Installation
- Propeller Shaft Transmission Flange Installation
- Torque Converter Installation and Holding Fixture Removal
- Transmission Housing Sound Insulator Installation
- Transmission Housing Sound Insulator Installation (10L60)