Section 60 (Crank Assembly - 212 Chassis - 2 Of 2)
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.
- Testing & Repair
- Inspect crankshaft bearing cap bolts
- Tightening procedure for crankcase bottom section - AR03.20-P-4351-05AMG
- Remove/install crankshaft
- Mount crankshaft radially in bearings - AR03.20-P-4355-01CD
- Mount crankshaft axially - AR03.20-P-4355-02CD
- Measure crankshaft and remount in bearings - AR03.20-P-4355CD
- Assign crankshaft bearing shells
- Inspecting belt pulley/vibration damper for axial and radial runout - AR03.30-P-1600-01SXI
- Remove/install belt pulley/vibration damper
- Remove/install belt pulley/vibration damper - AR03.30-P-1600CD
- Remove/install belt pulley/vibration damper - AR03.30-P-1600CMG
- Remove/install belt pulley/vibration damper - AR03.30-P-1600EL
- Remove/install belt pulley/vibration damper - AR03.30-P-1600EWS
- Remove/install belt pulley/vibration damper - AR03.30-P-1600SXI
- Remove/install retaining lock for crankshaft/ring gear
- Remove/install retaining lock for crankshaft/ring gear - AR03.30-P-5000CD
- Remove/install retaining lock for crankshaft/ring gear - AR03.30-P-5000CMG
- Remove/install retaining lock for crankshaft/ring gear - AR03.30-P-5000EL
- Remove/install retaining lock for crankshaft/ring gear - AR03.30-P-5000EWS
- Remove/install retaining lock for crankshaft/ring gear - AR03.30-P-5000SXI
- Remove/install flywheel/clutch plate - AR03.30-P-8001-02MM
- Remove/install flywheel/drive plate
- Remove/install flywheel/drive plate - AR03.30-P-8001CD
- Remove/install flywheel/drive plate - AR03.30-P-8001CMG
- Remove/install flywheel/drive plate - AR03.30-P-8001EHV
- Remove/install flywheel/drive plate - AR03.30-P-8001EL
- Remove/install flywheel/drive plate - AR03.30-P-8001EW
- Remove/install flywheel/drive plate - AR03.30-P-8001SXI
- Measure tilt and torsional play on two-mass flywheel - AR03.30-P-8010A
- Test & Adjustment Values
- Test and adjustment values: Passenger cars: Crank assembly - BE03.00-Z-9999AZ
- Check values for connecting rod
- Test specifications for pistons
- Test specifications for connecting rod bolts
- Check values for piston rings
- Check values for crankshaft bearing cap bolts
- Test specifications for crankshaft
- Check values for crankshaft main bearing shells
- Test specifications for crankshaft bearing clearance
- Belt pulley/vibration damper - BE03.30-P-1000-02D
- Flywheel - BE03.30-P-1000-03D
- Torque Specifications
- Special Tools
- 651 589 07 40 00 Counterholder - WS03.00-N-3115B
- 000 589 04 14 00 Tensioning strap - WS03.00-P-0001C
- 000 589 20 21 00 Hardness tester - WS03.00-P-0002C
- 000 589 51 37 00 Pliers - WS03.00-P-0005C
- 001 589 65 09 00 Socket - WS03.00-P-0006B
- 001 589 32 21 00 Dial gauge - WS03.00-P-0007B
- 111 589 08 43 03 Press-in sleeve - WS03.00-P-0016-01B
- 111 589 08 43 00 Installation tool - WS03.00-P-0016B
- 651 589 09 40 00 Hold-down tool - WS03.00-P-0018C
- 119 589 01 14 00 Sleeve - WS03.00-P-0022B
- 606 589 00 14 00 Shell - WS03.00-P-0035C
- 112 589 03 40 00 Retaining lock - WS03.00-P-0037B
- 112 589 00 40 01 Set of sleeves - WS03.00-P-0038-01B
- 112 589 00 40 00 Counterholder - WS03.00-P-0038B
- 611 589 00 14 00 Insertion tool - WS03.00-P-0042B
- 613 589 00 33 00 Puller - WS03.00-P-0044B
- 270 589 02 40 00 Retaining lock - WS03.00-P-0058C
- 246 589 02 43 00 Insertion device - WS03.00-P-0067B
- 272 589 00 14 00 Insertion tool - WS03.00-P-0090B
- 642 589 00 14 00 Centering sleeve - WS03.00-P-0094B
- 156 589 00 40 00 Crankshaft bracket - WS03.00-P-0101B
- 112 589 07 40 00 Counterholder - WS03.00-P-0102B
- 112 589 02 09 00 Socket - WS03.00-P-0109B
- 651 589 02 63 00 Assembly tool - WS03.00-P-0111C
- 651 589 00 61 00 Insertion tool - WS03.00-P-0112B
- 651 589 01 61 00 Insertion tool - WS03.00-P-0113B
- 651 589 00 40 00 Counterholder - WS03.00-P-0114B
- 272 589 00 07 00 Counterholder - WS03.00-P-0116B
- 651 589 00 43 00 Extraction and insertion tool - WS03.00-P-0120C