Section 82 (Liftgate - Vehicles With Power Liftgate - With Diagnostics)
WARNING: This page is about a different car, the 2014 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.
- Service Specifications
- Adhesive
- Special Tools
- Electric Tailgate Troubleshooting
- Diagnostic Trouble Code Procedures
- DTC B2480: Electromagnetic clutch short
- DTC B2481: Pulse sensor power supply short
- DTC B2482: No detection of neutral SW
- DTC B2483: No detection of full latch SW
- DTC B2484: Right side touch sensor open circuit
- DTC B2485: Left side touch sensor open circuit
- DTC B2488: ECU internal error
- DTC U0141: ETACS-ECU CAN Time-out
- DTC U0155: Meter CAN Time-out
- DTC U0164: A/C CAN time-out
- DTC U0168: KOS/WCM CAN Time-out
- DTC U0184: AUDIO CAN Time-out
- DTC U0245: AND CAN Time-out
- DTC U1000: OSS CAN Time-out
- DTC U1190 No receive fault detect signal
- DTC U1195 Coding not completed - Power Liftgate
- Data List Reference Table
- Actuator Test Table
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure A-1: Power supply circuit system abnormality of power liftgate control unit
- Inspection Procedure A-2: Power liftgate automatic operation and easy closer system do not work normally
- Inspection Procedure A-3: The power liftgateower liftgate automatic operation does not work normally (both the open operation and close operation do not work)
- Inspection Procedure A-4: Power liftgate automatic operation (close) does not work normally
- Inspection Procedure A-5: Power liftgate automatic operation (open) does not work normally
- Inspection Procedure A-6: Power liftgate automatic operation does not work normally by the operation of power liftgate close switch (only the close of automatic operation)
- Inspection Procedure A-7: Power liftgate automatic operation does not work normally by the operation of keyless operation key (for both open and close operations)
- Inspection Procedure A-8: Power liftgate automatic operation does not work normally by the operation of liftgate lock release handle (only the open of automatic operation)
- Inspection Procedure A-9: Power liftgate automatic operation does not work normally by the operation of power liftgate switch. (Open/close operation is not performed.)
- Inspection Procedure A-10: Easy closer system and power liftgate automatic operation (open) work with the door locked
- Inspection Procedure A-11: Hazard warning lights do not flash when power liftgate works automatically
- Inspection Procedure A-12: Alarm does not sound normally when power liftgate works automatically
- Inspection Procedure A-13: Power liftgate becomes as door-ajar
- Input Signal Chart
- Input Signal Procedures
- Inspection Procedure B-1: Power liftgate main switch signal is not received
- Inspection Procedure B-2: Power liftgate close switch signal is not received
- Inspection Procedure B-3: Liftgate lock release handle signal is not received
- Inspection Procedure B-4: Door-ajar signal is not received
- Inspection Procedure B-5: Neutral switch signal is not received
- Inspection Procedure B-6: Half latch switch and/or full latch switch signals are not received
- Inspection Procedure B-7: Liftgate sensor signal is not received
- Inspection Procedure B-8: Power liftgate switch signal is not received
- Check At Ecu Terminal
- On-Vehicle Service
- Liftgate
- Liftgate Handle And Latch
- Removal And Installation
- Inspection
- Liftgate Latch Check
- Latch Motor Operation Check
- Half Latch Switch Check
- Full Latch Switch Check
- Door-Ajar Switch Check
- Neutral Switch Check
- Liftgate Sensor Check
- Power Liftgate Close Switch Inspection
- Power Liftgate Main Switch Check
- Power Liftgate Switch Check
- Power Liftgate Tone Alarm Inspection
- Liftgate Lock Release Handle (Liftgate Open Switch) Check
- Liftgate Lock Release Handle (Liftgate Lock Switch) Check
- Liftgate Latch Check