Section 64 (Rear Axle - 212 Chassis - 1 Of 2)
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.
- General Information
- Testing & Repair
- Locate noises from rear axle - AR35.00-P-2000A
- Remove/install complete rear axle - AR35.10-P-0010EW
- Lower rear axle - AR35.10-P-0015EW
- Remove/install front rubber mount in rear axle mount - AR35.10-P-0040-02CW
- Remove/install rear rubber mount in rear axle mount - AR35.10-P-0040-03CW
- Remove/install front rubber bushings of rear axle suspension - AR35.10-P-0041EW
- Remove/install rear rubber bushings of rear axle suspension - AR35.10-P-0042EW
- Remove/install rear rubber mount of rear axle center assembly suspension - AR35.10-P-0050-02CW
- Remove/install rear rubber bushings for differential mount in rear axle carrier - AR35.10-P-0050EW
- Remove/install front differential mount on rear axle carrier - AR35.10-P-0051EW
- Remove/install spring control arm mount at rear axle carrier - AR35.20-P-0104EW
- Remove/install rubber mounts from thrust arm - AR35.20-P-0105-01CW
- Remove/install thrust arm bushing at the wheel carrier - AR35.20-P-0105EW
- Remove/install track rod - AR35.20-P-0109EW
- Remove/install camber strut - AR35.20-P-0110EW
- Remove/install radius rod - AR35.20-P-0111EW
- Remove/install thrust arm - AR35.20-P-0113EW
- Remove/install spring control arm rubber mount - AR35.20-P-0114-01CW
- Remove/install spring control arm, replace rubber bushing - AR35.20-P-0114EW
- Clean water drain in wheel carrier - AR35.20-P-0115-03CW
- Remove/install wheel carrier - AR35.20-P-0115EW
- Remove/install supporting joint on wheel carrier - AR35.20-P-0116-01CW
- Remove/install supporting joint at wheel carrier (wheel carrier installed) - AR35.20-P-0116EW
- Pull inner bearing race off rear-axle shaft flange - AR35.20-P-0130-02TX
- Pull rear axle shaft flange out of angular contact ball bearing - AR35.20-P-0130-06SX
- Pull rear axle shaft flange into angular contact ball bearing - AR35.20-P-0130-07SX
- Remove/install rear axle shaft flange and angular ball bearing - AR35.20-P-0130EW
- Remove/install and secure rear axle shaft twelve-point collar nut - AR35.30-P-0115-01TX
- Pressing out and drawing in rear axle shaft at rear axle shaft flange - AR35.30-P-0115-03SX
- Remove/install rear axle shaft - AR35.30-P-0620EW
- Boot cap on joint ring removal and installation - AR35.30-P-0661-01P
- Joint hub on rear axle shaft - Pressing off, pressing on and staking - AR35.30-P-0661-02P
- Dismantling constant-velocity joint, inspecting for wear, assembly - AR35.30-P-0661-03P
- Constant-velocity joint or rubber boot on rear halfshaft - removal and installation - AR35.30-P-0661P
- Check rear axle differential oil level, correct if necessary
- Drain oil from rear axle differential
- Remove/install differential - AR35.31-P-0520EW
- Measure and note down total friction torque of drive pinion - AR35.31-P-0530-04CWC
- Install new radial sealing ring at drive pinion gear (with differential installed)
- Replace radial sealing rings on side of rear axle center assembly
- Pulling off joint flange - AR35.31-P-0550-06CWC
- Adjusting friction torque of drive pinion bearing - AR35.31-P-0550-17CWC
- Remove/install end cover at differential