Section 7 (Engine - Repair (R61) -- Cooper Paceman)
WARNING: This page is about a different car, the 2016 MINI Cooper Paceman, 2015 MINI Cooper Paceman, 2014 MINI Cooper Paceman, and 2013 MINI Cooper. However, it is still accessible from the selected car via links, so may be relevant.
- Safety And General Information
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 00..... Safety instructions for handling oil
- Engine identification
- 11..... Equipment recoding special tool number of the transverse member for fixing the engine in the installation location
- 11 00... Engine oil service
- 11 00 039 Checking compression of all cylinders (N16 and N18)
- 11 00... Handling components after flood damage
- 11 00... Overview of consumables
- 11 00 Removing and installing/replacing acoustic cover (N16)
- 11 00 Removing and installing/replacing acoustic cover (N18)
- Mounting engine on assembly stand (N16)
- Mounting engine on assembly stand (N18)
- 11 00 670 Secure engine in installation position
- 11 00 050 Removing and installing engine with transmission (N18)
- 11 00 680 Replacing screw plug in crankcase lower half (N16)
- 11 00 680 Replacing screw plug in crankcase lower half (N18)
- Cylinder Head With Cover
- 11 12 729 Checking cylinder head for water leaks (N16)
- 11 12 729 Checking cylinder head for water leaks (N18)
- 11 12 100 Removing and installing/sealing cylinder head (N16)
- 11 12 100 Removing and installing/sealing cylinder head (N18)
- 11 12 000 Removing and installing/sealing cylinder head cover (N16)
- 11 12 000 Removing and installing/sealing cylinder head cover (N18)
- 11 12 101 Replacing cylinder head gasket (N16)
- 11 12 101 Replacing cylinder head gasket (N18)
- 11 12 719 Resurfacing cylinder head sealing face (N16)
- 11 12 719 Resurfacing cylinder head lower face (N18)
- Oil Sump
- Housing Cover
- Crankshaft With Bearing
- Flywheel
- Vibration Damper
- Connecting Rod With Bearing
- Piston With Rings And Pin
- V-Ribbed Belt With TENSIONER/Deflection Element
- 11 28 035 Removing and installing/replacing friction gear (N16)
- 11 28 035 Removing and installing/replacing friction gear (N18)
- 11 28 012 Replacing drive belt (without heating and air conditioning system)
- 11 28 010 Replacing drive belt for alternator (N16)
- 11 28 010 Replacing drive belt for alternator (N18)
- 11 28 020 Replacing tensioning device for alternator drive belt (N16)
- 11 28 020 Replacing tensioning device for alternator drive belt (N18)
- Camshaft
- 11 31 505 Adjusting camshaft timing (N16)
- 11 31 505 Adjusting camshaft timing (N18)
- 11 31 005 Check engine timing of camshaft (N16).
- 11 31 005 Checking camshaft timing (N18)
- 11 31 090 Installing and removing or replacing chain tensioner piston (N16)
- 11 31 090 Installing and removing or replacing chain tensioner piston (N18)
- 11 31 025 Removing and installing or replacing intake camshaft (N16)
- 11 31 025 Removing and installing or replacing intake camshaft (N18)
- 11 31 028 Removing and installing/replacing exhaust camshaft (N16)
- 11 31 028 Removing and installing/replacing exhaust camshaft (N18)
- 11 31 051 Replacing timing chain (N16)
- 11 31 051 Replacing timing chain (N18)
- Rocker Arm With Bearing Mount
- Valves With Springs
- 11 34 552 Removing and installing or replacing all valves (N16)
- 11 34 552 Removing and installing or replacing all valves (N18)
- 11 34 715 Replacing all valve springs (N16)
- 11 34 715 Replacing all valve springs (N18)
- 11 34 560 Replacing all valve stem seals (N16)
- 11 34 560 Replacing all valve stem seals (N18)
- Variable Camshaft Timing
- Variable Valve Gear
- 11 37 005 Removing and installing/replacing eccentric shaft (N16)
- 11 37 005 Removing and installing/replacing eccentric shaft (N18)
- 11 37 030 Removing and installing/replacing eccentric shaft sensor (N16)
- 11 37 010 Removing and installing/replacing intermediate levers (N16)
- 11 37 010 Removing and installing/replacing intermediate levers (N18)
- 11 37 020 Removing and installing/replacing positioning motor for eccentric shaft (N16)
- 11 37 020 Removing and installing/replacing positioning servomotor for eccentric shaft (N18)
- Oil Supply
- Oil Pump With Filter And Drive
- 11 41... Installing repair kit for oil pump solenoid valve wiring (N16, N18)
- 11 41 000 Removing and installing oil pump (N16)
- 11 41 000 Removing and installing oil pump (N18)
- 11 41 519 Removing and installing or replacing the solenoid valve (N16)
- 11 41 519 Removing and installing or replacing the solenoid valve (N18)
- 11 41... Retrofit oil pump solenoid valve additional wiring harness (N16, N18)
- Oil Filter And Lines
- Oil Filling, Dipstick
- Water Pump With Drive
- Thermostat And Connections
- Intake Manifold
- Exhaust Manifold
- Turbocharger With Control
- Vacuum Pump
- Electronic Valve For Exhaust Gas RECIRCULATION
- Emission Control, Oxygen Sensor