11 21 500 Replacing crankshaft (N16)

Special tools required: 

• 00 9 120
• 11 4 471
• 11 4 472
• 11 6 251
• 11 6 252
• 23 1 240

Necessary preliminary tasks: 

• Remove engine.
• Mount engine on ASSEMBLY STAND .
• Remove VIBRATION DAMPER .
• Removing OIL SUMP .
• Remove OIL PUMP .
• Remove TIMING CHAIN .
• Remove CYLINDER HEAD .
• Remove FLYWHEEL .

Release screws (1).

Tightening torque: 11 13 3AZ .

Remove oil deflector (2).

Remove all PISTONS .

Fig 1: Identifying Oil Deflector And Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Drive out cover plates (1) with a cross-cut chisel (2).

Fig 2: Driving Out Cover Plates With Cross-Chisel

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (28 to 11).

Release screws (10 to 1).

Fig 3: Lower Crankcase Bolts Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Release crankcase lower section in direction of arrow with a regular screwdriver (2) and an open-end spanner (1) at press-off lug.

Fig 4: Releasing Crankcase Lower Half

Courtesy of BMW OF NORTH AMERICA, INC.

Remove both radial shaft seals (1).

Fig 5: Identifying Radial Shaft Seals

Courtesy of BMW OF NORTH AMERICA, INC.

Remove crankshaft (1).

Remove MAIN BEARING SHELLS , replace if necessary.

Fig 6: Identifying Crankshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Clean sealing surfaces with special tools 11 4 471 and 11 4 472 .

Fig 7: Cleaning Sealing Surfaces With Special Tools (11 4 471) And (11 4 472)

Courtesy of BMW OF NORTH AMERICA, INC.

Apply sealing bead (1) to crankcase lower section (see illustration) with Loctite 5970 sealing compound.

Installation note: 

Follow manufacturer's instructions (Loctite).

Fig 8: Crankcase Lower Half Sealing Bead Application Area

Courtesy of BMW OF NORTH AMERICA, INC.

Apply sealing bead (1) to crankcase upper section (see illustration) with Loctite 5970 sealing compound.

Apply a light coating of engine oil to bearings.

Fig 9: Crankcase Upper Half Sealing Bead Application Area

Courtesy of BMW OF NORTH AMERICA, INC.

Insert crankshaft (1).

Fig 10: Identifying Crankshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Lubricate all bearings from 1 to 5 with engine oil.

Install crankcase lower section.

Position crankcase lower section using two dowel pins on the crankcase upper section.

Fig 11: Identifying Crankshaft Bearings

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten bolts (1 to 10).

Tightening torque: 11 11 1AZ .

Tighten bolts (11 to 28).

Tightening torque: 11 11 2AZ .

Fig 12: Lower Crankcase Bolts Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Only use special tool to secure bolts 00 9 120 .

Fig 13: Tightening Bolts Using Special Tool (00 9 120)

Courtesy of BMW OF NORTH AMERICA, INC.

To prevent oil leakage, apply a thin coating of LOCTITE 648  to cover sleeve (1) in area (2).

Fig 14: Identifying Loctite Application Area On Cover Sleeve

Courtesy of BMW OF NORTH AMERICA, INC.

Knock in cover sleeves with special tool 23 1 240 as far as they will go.

Fig 15: Installing Cover Sleeves With Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Determine SIDE CLEARANCE of crankshaft.

Affix special tool 11 6 252 with magnet.

Set special tool 11 6 251 to zero.

Press crankshaft in direction of arrow to the limit position.

Fig 16: Checking Side Clearance Of Crankshaft Using Special Tools (11 6 252) And (116 251)

Courtesy of BMW OF NORTH AMERICA, INC.

Replace radial shaft seal at FRONT .

Replace radial shaft seal at REAR .

Assemble engine.