Section 3 (Complete Engine (1 Of 2) -- 118 Chassis)
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
- Description & Operation
- General Information
- General Information On Inspecting Cylinder Walls
- Determine Loss Of Pressure At Cylinder - AH01.00-P-1300-02KOA
- (Firing Order - AH01.00-Z-0100-02KOP)
- General Notes: Passenger Cars: Complete Engine, Crankcase Ventilation, Cylinder Head, Crankcase - AH01.00-Z-9999AZ
- Use Of Engine No. When Installing Reconditioned Engines And Factory-New Replacement Engines Or Crankcases - AH01.10-P-0001-01A
- Notes On Sealant Path For Front Cover To Cylinder Head XXX - AH01.30-P-1000-02MR
- Notes On Sealant Path For Cylinder Head Cover - AH01.30-P-1000-08MM
- Notes On Sealant Path For Timing Case Cover
- Notes On Sealant Path For Oil Engine Pan - AH01.45-P-0001-01MMA
- Basic Knowledge
- Combustion Engine Mechanical Components, Basic Function - GF01.00-P-9900A
- Combustion Engine, Basic Function - GF01.00-P-9901A
- Table Of Contents For Function Description Of Engine Comment - GF01.10-Z-0999A
- Table Of Contents For Function Description Of Engine - GF01.10-Z-0999F
- Crankcase, Basic Function - GF01.40-P-1000A
- Safety Precautions
- Testing & Repair
- Assemble/Disassemble Engine On Engine Assembly Stand - AR01.00-P-0002-01MFG
- Remove Sealant - AR01.00-P-0050-01A
- Inspect Cylinders With A Light Probe
- Check Compression Pressure
- Connect Cylinder Leakage Testing Unit - AR01.00-P-1300-01MFG
- Firing Order - AR01.00-P-1300-03MM
- Check Cylinders For Leaks
- Connecting Recording-Type Compression Tester
- Prepare Engine Support Fixture During Repair Work In Vehicle - AR01.10-P-0105-02MFA
- Prepare Engine Support Fixture For Removal Of Engine/Transmission Unit - AR01.10-P-0105-03MFA
- Mount/Remove Support Fixture For Removal Of Engine/Transmission Unit - AR01.10-P-0106MFA
- Mount/Remove Support Fixture For Engine/Transmission Unit For Repair Operations - AR01.10-P-0107MFA
- Crank Engine With Starter - AR01.10-P-0110MFG
- Turn Engine To Top Dead Center Position
- Remove/Install Engine With Transmission
- (Remove/Install Engine With Transmission - AR01.10-P-2401MFJ)
- Position Portable Lifting Platform - AR01.10-P-2500-01A
- Remove/Install Wide Open Throttle Vent Line - AR01.20-P-0020MFC
- Remove/Install Full-Load Crankcase Ventilation System - AR01.20-P-0025MFC
- (Remove/Install Partial Load Crankcase Ventilation System Valve - AR01.20-P-0040MFC)
- Remove/Install Partial Load Crankcase Ventilation System Valve - AR01.20-P-0040MFD
- Bolt Tightening Procedure For Cylinder Head Cover
- Remove/Install Cylinder Head Cover
- (Remove/Install Oil Engine Separator - AR01.20-P-9750MFC)
- Remove/Install Engine Oil Separator
- Apply Sealant To Rear Cap On Cylinder Head - AR01.30-P-0002-01MFG
- Remove/Install Rear Cover On Cylinder Head - AR01.30-P-5702MFG
- Tightening Procedure For Cover On Cylinder Head - AR01.30-P-5706-01MFG
- Tightening Procedure For Cylinder Head Bolts
- Remove/Install Tensioning Rail Bolt And Slide Rail Bolt - AR01.30-P-5800-21MFC
- Remove/Install Cylinder Head - AR01.30-P-5800MFC
- Remove/Install Cylinder Head - AR01.30-P-5800MFG
- Loosen/Tighten Oil And Coolant Pump Drive Unit Screws/Bolts - AR01.40-P-0001-01MFG
- Remove/Install Drive Unit For Oil And Coolant Pump - AR01.40-P-0006MFG
- Loosen/Tighten Upper Timing Case Cover Screws - AR01.40-P-0122-01MFC
- Bolt Plan For Timing Case Cover
- Remove/Install Timing Case Cover - AR01.40-P-8000MFG
- Remove/Install Upper Timing Case Cover - AR01.40-P-8001MFC
- Timing Gear Casing - Remove/Install Lower Cover - AR01.40-P-8002MFC
- Detach/Attach Front Cap With Radial Shaft Sealing Ring - AR01.40-P-8922-03MFG
- Remove/Install Cap With Front Radial Shaft Sealing Ring - AR01.40-P-8922MFG
- Apply Sealant To Oil Engine Pan - AR01.45-P-0002-01MFG
- Tightening Procedure For Oil Engine Pan Bolts - AR01.45-P-7500-01MFC
- Remove/Install Oil Engine Pan
- Loosen/Tighten Oil Engine Pan Screws - AR01.45-P-7503-01MFG