Remove and install/replace torque converter (X2 xDrive 28i 2020-2023, X2 M35i 2019-2022)

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW X2, 2022 BMW X2, 2021 BMW X2, 2020 BMW X2, and 2019 BMW X2. However, it is still accessible from the selected car via links, so may be relevant.

WARNING: Car may slip off the vehicle hoist where components are supported .
Danger! Immobilization period-threatening injuries!

Secure the vehicle hoist against lowering and lifting.
Make sure that the vehicle does not lift off the mounting plates on the vehicle lift.

WARNING: Car may slip off the vehicle hoist if the weight is distributed unevenly .
Danger! Immobilization period-threatening injuries!

Ensure there is a specific weight compensation on the car.

WARNING: Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly .
Danger! Immobilization period-threatening injuries!

Observe safety instructions on raising the vehicle using a vehicle hoist.
For additional information see: RAISING THE VEHICLE WITH A VEHICLE LIFT) .

CAUTION: Component with heavy weight .
Injury hazard!

Note component's center of gravity.
Support component using a jack.
Secure component against falling off the jack.

CAUTION: Materials harmful to health .
Contact with fluids harmful to health!

Note and follow safety instructions on containers.
Conduct all work in appropriate personal protective equipment only.

Preliminary work

Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
Refer to REMOVING SUSPENSION CROSS-BRACE .
Refer to REMOVING REAR HOOD SEAL .
Refer to REMOVING FRONT WINDSHIELD PANEL COVER .
Refer to REMOVING THE UPPER FIREWALL COVER PANEL .
Refer to REMOVING THE ACOUSTIC COVER .
Refer to REMOVING THE INTAKE MANIFOLD FOR INTAKE SILENCER HOUSING .
Refer to REMOVING INTAKE SILENCER HOUSING .
Refer to DISCONNECTING CABLE FROM BATTERY EARTH LEAD .
Refer to REMOVING THE SYSTEM BATTERY .
Refer to REMOVING FRONT CROSS CONNECTION .
Refer to REMOVING FAN COWL WITH ELECTRIC FAN .
Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
Refer to DRAINING THE COOLANT FROM THE COOLANT CIRCUIT .
Refer to CONNECTING COOLANT LINE .
Refer to INSTALLING FAN COWL WITH ELECTRIC FAN .
Refer to INSTALLING FRONT CROSS CONNECTION .
Refer to INSTALLING THE ENGINE BRIDGE .
Refer to REMOVING STARTER MOTOR .
Refer to DETACHING STEERING SHAFT AT BOTTOM FROM STEERING GEAR .
Refer to ATTACHING THE LEFT AND RIGHT COOLANT RADIATOR .
Refer to REMOVING FRONT LEFT OR RIGHT WHEEL .
Refer to IF INSTALLED: REMOVING REAR UNDERBODY PROTECTION .
Refer to REMOVING FRONT LEFT AND RIGHT WHEEL ARCH COVER .
Refer to WITH RIGHT INSTALLATION: DETACHING THE CABLE FOR THE RIDE HEIGHT SENSOR .
Refer to RELEASING THE LEFT AND RIGHT ANTI-ROLL BAR FROM THE ANTI-ROLL BAR LINK .
Refer to DETACHING RUBBER MOUNT FROM FRONT AXLE SUPPORT .
Refer to DISCONNECTING PLUG CONNECTIONS FROM STEERING GEAR .
Refer to DISCONNECTING PURGE AIR LINE .
Refer to RELEASING ATTACHMENTS FROM THE FRONT AXLE SUPPORT .
Refer to DETACHING AND REMOVING FRONT AXLE COMPLETELY .
Refer to PARTIALLY REMOVING LEFT OUTPUT SHAFT .
Refer to PARTIALLY REMOVING RIGHT OUTPUT SHAFT .
Refer to REMOVING EXHAUST SYSTEM .
Refer to REMOVING FRONT HEAT SHIELD .
Refer to REMOVING HEAT SHIELD AT REAR .
Refer to REMOVING PROP SHAFT .
Refer to REMOVING THE INTERMEDIATE SHAFT WITH THE SUPPORT TUBE .
Refer to REMOVING HOLDER WITH RUBBER MOUNT .
Refer to REMOVING TRANSFER BOX (VTG) .
Refer to REMOVING THE AUTOMATIC TRANSMISSION (X2 XDRIVE 28I 2020-2023) or REMOVING THE AUTOMATIC TRANSMISSION (X2 M35I 2019-2022) .

Follow-up work

Refer to INSTALLING THE AUTOMATIC TRANSMISSION (X2 XDRIVE 28I 2020-2023) or INSTALLING AUTOMATIC TRANSMISSION (X2 M35I 2019-2022) .
Refer to INSTALLING THE TRANSFER BOX (VTG) .
Refer to INSTALLING HOLDER WITH RUBBER MOUNT .
Refer to INSTALLING THE INTERMEDIATE SHAFT WITH THE SUPPORT TUBE .
Refer to INSTALLING PROP SHAFT .
Refer to INSTALLING THE REAR HEAT SHIELD .
Refer to INSTALLING FRONT HEAT SHIELD .
Refer to INSTALLING EXHAUST SYSTEM .
Refer to PARTIALLY INSTALLING RIGHT OUTPUT SHAFT .
Refer to PARTIALLY INSTALLING THE LEFT OUTPUT SHAFT .
Refer to MOUNTING AND SECURING THE COMPLETE FRONT AXLE .
Refer to SECURING THE MOUNTED PART ON THE FRONT AXLE SUPPORT .
Refer to CONNECTING PURGE AIR LINE .
Refer to ATTACHING CONNECTOR AT STEERING GEAR .
Refer to FASTENING THE RUBBER MOUNT ON THE FRONT AXLE SUPPORT .
Refer to SECURING THE ANTI-ROLL BAR ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR LINK .
Refer to WITH RIGHT INSTALLATION: FASTENING THE CABLE FOR THE RIDE HEIGHT SENSOR .
Refer to INSTALLING FRONT LEFT AND RIGHT WHEEL ARCH COVER .
Refer to IF INSTALLED: INSTALLING UNDERBODY PROTECTION AT REAR .
Refer to INSTALLING THE FRONT LEFT OR RIGHT WHEEL .
Refer to INSTALLING STARTER MOTOR .
Refer to REMOVING COOLANT RADIATOR ATTACHMENT ON THE LEFT AND RIGHT .
Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
Refer to REMOVING THE ENGINE BRIDGE .
Refer to INSTALLING THE SYSTEM BATTERY .
Refer to CONNECTING BATTERY GROUND LEAD .
Refer to INSTALLING INTAKE SILENCER HOUSING .
Refer to INSTALLING THE INTAKE MANIFOLD FOR THE INTAKE FILTER HOUSING .
Refer to FILLING THE COOLANT CIRCUIT WITH THE VACUUM FILLING EQUIPMENT .
Refer to AIR BLEEDING THE COOLANT CIRCUIT .
Refer to CHECKING/TOPPING UP OIL LEVEL IN AUTOMATIC TRANSMISSION (AISIN GA8G45) .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
Refer to INSTALLING THE STRUT BRACE .
Refer to INSTALLING THE REAR HOOD SEAL .
Refer to INSTALLING FRONT WINDSHIELD PANEL COVER .
Refer to INSTALLING THE UPPER FIREWALL COVER PANEL .
Refer to INSTALLING ACOUSTIC COVER .
Refer to TAKING HOOD OUT OF THE SERVICE POSITION .