Section 366 (Crank Assembly - 253 Chassis)
WARNING: This page is about a different car, the 2023 Mercedes-Benz GLC300, 2022 Mercedes-Benz GLC300, 2021 Mercedes-Benz GLC300, 2020 Mercedes-Benz GLC350e, and 2020 Mercedes-Benz GLC300. However, it is still accessible from the selected car via links, so may be relevant.
- General Information
- General Notes: Passenger Cars: Crank Assembly - AH03.00-Z-9999AZ
- Notes On Assessing Wear On Connecting Rod Bearings And Connecting Rod Journals - AH03.10-P-0001-03MM
- Notes On The Assessment Of Pistons And Piston Rings - AH03.10-P-0001-04MM
- Information On Assessing Wear Of Main Bearings And Main Bearing Journals - AH03.20-P-1000-02MM
- Interference Fit Of Crankshaft Bearing Cap - AH03.20-P-4351-02MM
- Safety Precautions
- Testing & Repair
- Check Connecting Rod Bolts
- Tighten Connecting Rod Bolts
- Install And Gauge Connecting Rod Bearings - AR03.10-P-6111-06MR
- Mount Connecting Rod Bearing - AR03.10-P-6111-08MRH
- Assign Connecting Rod Bearing Shells - AR03.10-P-6112-01MRH
- Remove/Install Piston
- Measure Vertical Clearance Of Piston Rings
- Measure Piston Ring End Gap
- Remove/Install Piston Rings
- Remove Corrosion From Crankshaft - AR03.20-P-1000-01A
- Move Lanchester Balance Shaft To Basic Position - AR03.20-P-1100-05MR
- Remove/Install Lanchester Balancer - AR03.20-P-1100MRA
- Remove/Install Balance Shaft Housing - AR03.20-P-1105MRI
- Install Front Crankshaft Radial Seal Ring
- Replace Front Crankshaft Radial Sealing Ring
- Replace Rear Crankshaft Radial Sealing Ring
- Install Rear Crankshaft Radial Sealing Ring
- Determine Crankshaft Bearing Axial Play
- Install Crankshaft Main Bearing - AR03.20-P-4341-03MRH
- Tightening Procedure For Crankshaft Bearing Caps - AR03.20-P-4351-02MR
- Tightening Specification For Crankshaft Bearing Cap Screws/Bolts - AR03.20-P-4351-06MRH
- Remove/Install Crankshaft
- Assign Crankshaft Bearing Shells
- Check Crankshaft In Removed State
- Remove/Install Belt Pulley/Vibration Damper
- Remove/Install Retaining Lock For Crankshaft/Ring Gear
- Remove/Install Flywheel/Drive Plate - AR03.30-P-8001MRA
- Remove/Install Drive Plate - AR03.30-P-8003MRI
- Measure Tilting And Torsioning Play At Two-Mass Flywheel - AR03.30-P-8010MRA
- Test & Adjustment Values
- Test And Adjustment Values: Passenger Cars: Crank Assembly - BE03.00-Z-9999AZ
- Test Specifications For Pistons - BE03.10-P-1000-02L
- Test Specifications For Connecting Rod Bolts
- Check Values For Piston Rings - BE03.10-P-1000-05L
- Test Specifications For Crankshaft
- Check Values For Crankshaft Main Bearing Shells - BE03.20-P-1000-03L
- Test Specifications For Crankshaft Bearing Clearance - BE03.20-P-1000-04H
- Lanchester Balancer - BE03.20-P-1000-05B
- Thrust Plate Test Specifications - BE03.20-P-1000-08A
- Flywheel - BE03.30-P-1000-03D
- Torque Specifications
- Special Tools
- 000 589 04 14 00 Tensioning Strap - WS03.00-P-0001C
- 000 589 20 21 00 Hardness Tester - WS03.00-P-0002C
- 000 589 51 37 00 Pliers - WS03.00-P-0005C
- 001 589 65 09 00 Socket Wrench Bit - WS03.00-P-0006B
- 001 589 32 21 00 Dial Indicator - WS03.00-P-0007B
- 119 589 01 14 00 Sleeve - WS03.00-P-0022B
- 112 589 03 40 00 Retaining Lock - WS03.00-P-0037B
- 000 589 27 33 00 Internal Extractor - WS03.00-P-0049C
- 270 589 02 40 00 Retaining Lock - WS03.00-P-0058C
- 274 589 00 31 00 Adapter - WS03.00-P-0060B
- 270 589 00 15 00 Drift - WS03.00-P-0061B
- 270 589 00 68 00 Adapter - WS03.00-P-0062B
- 230 589 00 40 00 Counterholder - WS03.00-P-0068B
- 654 589 00 40 00 Counterholder - WS03.00-P-0079B
- 270 589 03 40 00 Retaining Lock - WS03.00-P-0105A
- 270 589 00 33 02 Spindle - WS03.00-P-0125-02B
- 270 589 00 33 00 Puller - WS03.00-P-0125B
- 001 589 93 21 00 Dial Indicator - WS03.00-P-0169B