Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| APIM | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| BCM | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| BCMC | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| BECM | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| DCDC | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| IPC | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| PAM | U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| SOBDMC | C0030:00 | Left Front Tone Wheel: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0033:00 | Right Front Tone Wheel: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0036:00 | Left Rear Tone Wheel: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0039:00 | Right Rear Tone Wheel: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0049:00 | Brake Fluid Level: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C004B:00 | Brake Fluid Level Sensor/Switch Circuit/Open: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C004C:00 | Brake Booster Motor "A" Position Sensor Exceeded Learning Limit: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C004E:00 | Brake System Pressure Control Valve Actuator Stuck: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C004F:00 | ABS Control Module Over Temperature: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0061:00 | Lateral Acceleration Sensor: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0062:00 | Longitudinal Acceleration Sensor: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0500:00 | Left Front Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0501:00 | Left Front Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0504:00 | Left Front Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0506:00 | Right Front Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0507:00 | Right Front Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C050A:00 | Right Front Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C050C:00 | Left Rear Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C050D:00 | Left Rear Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0510:00 | Left Rear Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0512:00 | Right Rear Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0513:00 | Right Rear Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0516:00 | Right Rear Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0518:00 | Left Front Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0519:00 | Right Front Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C051A:00 | Left Rear Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C051B:00 | Right Rear Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C052B:00 | ABS Pump Motor Control Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C052D:00 | ABS Pump Motor Control Circuit High: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C052E:00 | ABS Pump Motor Control Circuit Low: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C053D:00 | Brake Pressure Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0555:00 | Left Front Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0556:00 | Right Front Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0557:00 | Left Rear Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0558:00 | Right Rear Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C055C:00 | ABS Pump Motor Supply Voltage Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C055E:00 | Brake Hydraulic Circuit "A" Leak: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0560:00 | Brake Pressure Sensor "A" Missing Calibration: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0563:00 | ABS Control Module Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0564:00 | ABS Control Module System Voltage Low: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0565:00 | ABS Control Module System Voltage High: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C056A:00 | Brake Booster Pressure Sensor Power Supply Circuit: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C056B:00 | Brake Pressure Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0594:00 | Brake Booster Motor "A" Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0596:00 | Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C0597:00 | Brake System Control Module "A" Performance: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C1013:00 | Brake System Pressure: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C101F:00 | Generic Valve Failure: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | C113A:62 | Wake-up Control: Signal Compare Failure | GO to Pinpoint Test A |
| SOBDMC | P0560:00 | System Voltage: No Sub Type Information | GO to Pinpoint Test BI |
| SOBDMC | P0562:00 | System Voltage Low: No Sub Type Information | GO to Pinpoint Test BI |
| SOBDMC | P0563:00 | System Voltage High: No Sub Type Information | GO to Pinpoint Test C |
| SOBDMC | P0600:49 | Serial Communication Link: Internal Electronic Failure | GO to Pinpoint Test D |
| SOBDMC | P0600:88 | Serial Communication Link: Bus Off | GO to Pinpoint Test D |
| SOBDMC | P0607:00 | Control Module Performance: No Sub Type Information | GO to Pinpoint Test E |
| SOBDMC | P060A:44 | Internal Control Module Monitoring Processor Performance: Data Memory Failure | GO to Pinpoint Test F |
| SOBDMC | P060A:47 | Internal Control Module Monitoring Processor Performance: Watchdog/Safety μC Failure | GO to Pinpoint Test F |
| SOBDMC | P060A:86 | Internal Control Module Monitoring Processor Performance: Signal Invalid | GO to Pinpoint Test D |
| SOBDMC | P060A:88 | Internal Control Module Monitoring Processor Performance: Bus Off | GO to Pinpoint Test D |
| SOBDMC | P060B:47 | Internal Control Module A/D Processing Performance: Watchdog/Safety μC Failure | GO to Pinpoint Test G |
| SOBDMC | P060B:62 | Internal Control Module A/D Processing Performance: Signal Compare Failure | GO to Pinpoint Test G |
| SOBDMC | P060C:41 | Internal Control Module Main Processor Performance: General Checksum Failure | GO to Pinpoint Test H |
| SOBDMC | P060C:42 | Internal Control Module Main Processor Performance: General Memory Failure | GO to Pinpoint Test H |
| SOBDMC | P060C:44 | Internal Control Module Main Processor Performance: Data Memory Failure | GO to Pinpoint Test H |
| SOBDMC | P060C:47 | Internal Control Module Main Processor Performance: Watchdog/Safety μC Failure | GO to Pinpoint Test H |
| SOBDMC | P0613:86 | TCM Processor: Signal Invalid | GO to Pinpoint Test I |
| SOBDMC | P061A:92 | Internal Control Module Torque Performance: Performance or Incorrect Operation | GO to Pinpoint Test BJ |
| SOBDMC | P061A:93 | Internal Control Module Torque Performance: No Operation | GO to Pinpoint Test BJ |
| SOBDMC | P0634:00 | Control Module Internal Temperature "A" Too High: No Sub Type Information | GO to Pinpoint Test J |
| SOBDMC | P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test K |
| SOBDMC | P06A6:00 | Sensor Reference Voltage "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| SOBDMC | P06A7:00 | Sensor Reference Voltage "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| SOBDMC | P06A9:00 | Sensor Reference Voltage "D" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test L |
| SOBDMC | P06B1:00 | Sensor Power Supply "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| SOBDMC | P06B8:00 | Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information | GO to Pinpoint Test M |
| SOBDMC | P0886:00 | TCM Power Relay Control Circuit Low: No Sub Type Information | GO to Pinpoint Test N |
| SOBDMC | P0887:00 | TCM Power Relay Control Circuit High: No Sub Type Information | GO to Pinpoint Test N |
| SOBDMC | P0A0A:13 | High Voltage System Interlock Circuit "A": Circuit Open | GO to Pinpoint Test BK |
| SOBDMC | P0A1A:06 | Generator Control Module: Algorithm Based Failures | GO to Pinpoint Test O |
| SOBDMC | P0A1D:08 | Hybrid/EV Powertrain Control Module "A": Bus Signal/Message Failures | GO to Pinpoint Test P |
| SOBDMC | P0A23:00 | Generator Torque Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test Q |
| SOBDMC | P0A2F:94 | Drive Motor "A" Over Temperature: Unexpected Operation | GO to Pinpoint Test R |
| SOBDMC | P0A37:64 | Generator Temperature Sensor Circuit Range/Performance: Signal Plausibility Failure | GO to Pinpoint Test S |
| SOBDMC | P0A38:00 | Generator Temperature Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test S |
| SOBDMC | P0A39:00 | Generator Temperature Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test S |
| SOBDMC | P0A3C:94 | Drive Motor "A" Inverter Over Temperature: Unexpected Operation | GO to Pinpoint Test T |
| SOBDMC | P0A47:00 | Drive Motor "B" Position Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test U |
| SOBDMC | P0A4C:00 | Generator Position Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test V |
| SOBDMC | P0A4D:00 | Generator Position Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test W |
| SOBDMC | P0A50:92 | Generator Position Sensor Circuit Overspeed: Performance Or Incorrect Operation | GO to Pinpoint Test X |
| SOBDMC | P0A6F:00 | Generator Phase U Current: No Sub Type Information | GO to Pinpoint Test Y |
| SOBDMC | P0A71:00 | Generator Phase U Current High: No Sub Type Information | GO to Pinpoint Test Z |
| SOBDMC | P0A72:00 | Generator Phase V Current: No Sub Type Information | GO to Pinpoint Test Y |
| SOBDMC | P0A74:00 | Generator Phase V Current High: No Sub Type Information | GO to Pinpoint Test Z |
| SOBDMC | P0A75:00 | Generator Phase W Current: No Sub Type Information | GO to Pinpoint Test Y |
| SOBDMC | P0A77:00 | Generator Phase W Current High: No Sub Type Information | GO to Pinpoint Test Z |
| SOBDMC | P0A7A:96 | Generator Inverter Performance: Component Internal Failure | GO to Pinpoint Test AA |
| SOBDMC | P0BCD:00 | Generator Inverter Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test AB |
| SOBDMC | P0BCE:00 | Generator Inverter Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test AC |
| SOBDMC | P0BCF:00 | Generator Inverter Temperature Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test AC |
| SOBDMC | P0C03:00 | Drive Motor "B" Current Low: No Sub Type Information | GO to Pinpoint Test AD |
| SOBDMC | P0C2F:62 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: Signal Compare Failure | GO to Pinpoint Test AE |
| SOBDMC | P0C2F:63 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: Circuit/Component Protection Time-Out | GO to Pinpoint Test AE |
| SOBDMC | P0C5A:00 | Drive Motor "B" Position Sensor Circuit "A": No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C5C:00 | Drive Motor "B" Position Sensor Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C5D:00 | Drive Motor "B" Position Sensor Circuit "A" High: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C5F:00 | Drive Motor "B" Position Sensor Circuit "B": No Sub Type Information | GO to Pinpoint Test AI |
| SOBDMC | P0C61:00 | Drive Motor "B" Position Sensor Circuit "B" Low: No Sub Type Information | GO to Pinpoint Test AI |
| SOBDMC | P0C62:00 | Drive Motor "B" Position Sensor Circuit "B" High: No Sub Type Information | GO to Pinpoint Test AI |
| SOBDMC | P0C64:00 | Generator Position Sensor Circuit A: No Sub Type Information | GO to Pinpoint Test U |
| SOBDMC | P0C65:00 | Generator Position Sensor Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test AF |
| SOBDMC | P0C66:00 | Generator Position Sensor Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C67:00 | Generator Position Sensor Circuit "A" High: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C6A:00 | Generator Position Sensor Circuit "B" Range/Performance: No Sub Type Information | GO to Pinpoint Test AH |
| SOBDMC | P0C6B:00 | Generator Position Sensor Circuit "B" Low: No Sub Type Information | GO to Pinpoint Test AI |
| SOBDMC | P0C6C:00 | Generator Position Sensor Circuit "B" High: No Sub Type Information | GO to Pinpoint Test AI |
| SOBDMC | P0C79:00 | Drive Motor "A" Inverter Voltage Too High: No Sub Type Information | GO to Pinpoint Test AJ |
| SOBDMC | P0DA8:00 | Hybrid/EV Battery Voltage/Drive Motor "A" Inverter Voltage Correlation: No Sub Type Information | GO to Pinpoint Test AK |
| SOBDMC | P0DFA:00 | Generator Phase U-V-W Current Sensor Correlation: No Sub Type Information | GO to Pinpoint Test AL |
| SOBDMC | P0DFC:00 | Generator Position Sensor Not Learned: No Sub Type Information | GO to Pinpoint Test AM |
| SOBDMC | P0E71:00 | Generator Torque Delivered Performance: No Sub Type Information | GO to Pinpoint Test AN |
| SOBDMC | P1A07:00 | Inverter High Voltage Performance: No Sub Type Information | GO to Pinpoint Test AO |
| SOBDMC | P1A0A:02 | Immediate Shutdown Signal A: General Signal Failure | GO to Pinpoint Test AP |
| SOBDMC | P1A0E:61 | Hybrid Powertrain Control Module - Motor Disabled: Signal Calculation Failure | GO to Pinpoint Test H |
| SOBDMC | P1A0E:62 | Hybrid Powertrain Control Module - Motor Disabled: Signal Compare Failure | GO to Pinpoint Test AL |
| SOBDMC | P1A0E:64 | Hybrid Powertrain Control Module - Motor Disabled: Signal Plausibility Failure | GO to Pinpoint Test AL |
| SOBDMC | P1A0E:96 | Hybrid Powertrain Control Module - Motor Disabled: Component Internal Failure | GO to Pinpoint Test AL |
| SOBDMC | P2531:00 | Ignition Switch Run Position Circuit Low: No Sub Type Information | GO to Pinpoint Test BH |
| SOBDMC | P2533:1F | Ignition Switch On/Start Position Circuit: Circuit Intermittent | GO to Pinpoint Test BH |
| SOBDMC | P2533:62 | Ignition Switch On/Start Position Circuit: Signal Compare Failure | GO to Pinpoint Test AQ |
| SOBDMC | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AR |
| SOBDMC | U010F:00 | Lost Communication With Air Conditioning Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| SOBDMC | U0111:00 | Lost Communication With Battery Energy Control Module "A": No Sub Type Information | GO to Pinpoint Test AT |
| SOBDMC | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AU |
| SOBDMC | U0128:00 | Lost Communication With Park Brake Control Module: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AV |
| SOBDMC | U0143:00 | Lost Communication With Body Control Module "C": No Sub Type Information | GO to Pinpoint Test AW |
| SOBDMC | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AX |
| SOBDMC | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AY |
| SOBDMC | U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test AZ |
| SOBDMC | U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test BL |
| SOBDMC | U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| SOBDMC | U019B:00 | Lost Communication With Battery Charger Control Module "A": No Sub Type Information | GO to Pinpoint Test BN |
| SOBDMC | U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test BA |
| SOBDMC | U0298:00 | Lost Communication With DC/DC Converter Control Module "A": No Sub Type Information | GO to Pinpoint Test BB |
| SOBDMC | U0315:00 | Software Incompatibility with Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | U063B:87 | Lost Communication With Coolant Bypass Valve Actuator "A": Missing Message | GO to Pinpoint Test BO |
| SOBDMC | U0647:00 | Lost Communication with Motor Electronics Coolant Pump "B": No Sub Type Information | GO to Pinpoint Test BP |
| SOBDMC | U069E:81 | Lost Communication With Coolant Heater "A": Invalid Serial Data Received | GO to Pinpoint Test BQ |
| SOBDMC | U069E:87 | Lost Communication With Coolant Heater "A": Missing Message | GO to Pinpoint Test BQ |
| SOBDMC | U1011:86 | Invalid Internal Control Module Monitoring Data Received from ECM/PCM: Signal Invalid | GO to Pinpoint Test BC |
| SOBDMC | U1027:00 | ABS Control Module Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BD |
| SOBDMC | U301B:00 | Control Module Wake-up Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test BE |
| SOBDMC | U351B:00 | High Voltage System Interlock Circuit "D" Low: No Sub Type Information | GO to Pinpoint Test BF |