Pinpoint Test Bn : U019B
- Normal Operation and Fault Conditions
REFER to: Electric Powertrain Control - System Operation and Component Description .
DTC Fault Trigger Conditions
DTC Description Fault Trigger Condition SOBDMC U019B:00 Lost Communication With Battery Charger Control Module "A": No Sub Type Information This DTC sets when messages are missing from the SOBDM. Possible Sources
- Communications network concern
- SOBDM (Battery Charger Control Module)
- BN1 CARRY OUT A VEHICLE INSPECTION AND VERIFY THE SELF-TEST PROCEDURENOTE: If the self-test or communication concern occurred after a failed or aborted reprogram, the module may be blank. Attempt to reprogram the module again before continuing with this pinpoint test.
- Visually inspect the following for obvious signs of electrical damage:
- harness wiring
- electrical connections
- Verify the correct procedure was used to activate the self-test for the scan tool. Refer to SCAN TOOL SETUP AND FUNCTIONALITY .
Was the correct self-test procedure used?
Yes GO to BN2 No Refer to SCAN TOOL SETUP AND FUNCTIONALITY . - Visually inspect the following for obvious signs of electrical damage:
- BN2 CARRY OUT THE NETWORK TEST
- Note:
When using FDRS, the scan tool attempts to communicate with the PCM first. After establishing communication with the PCM, the scan tool then attempts to communicate with all modules on the vehicle. If an FDRS session cannot be established, FDRS may state no communication can be established with the PCM:
- Choose No when the scan tool prompts whether or not to retry communication.
- Enter a PCM part number, tear tag or calibration number to identify the vehicle and start a session. The PCM part number and 4- character tear tag are located on the PCM.
- Ignition ON.
Do all modules indicate pass?
Yes GO to BN3 No GO to BN4 - Note:
When using FDRS, the scan tool attempts to communicate with the PCM first. After establishing communication with the PCM, the scan tool then attempts to communicate with all modules on the vehicle. If an FDRS session cannot be established, FDRS may state no communication can be established with the PCM:
- BN3 CHECK FOR A SOBDM (SECONDARY ON-BOARD DIAGNOSTIC CONTROL MODULE A) CONCERN
- Using a diagnostic scan tool, perform the SOBDM self-test.
- Check for any other SOBDM related symptoms.
Is a concern present?
Yes DIAGNOSE the SOBDM concern. REFER to: Information and Entertainment System - Vehicles With: SYNC 3 . No The system is operating correctly at this time. The concern may have been caused by module connections. Address the root cause of any connector or pin issues. - BN4 INVERTER SYSTEM CONTROLLER (ISC) SELF-TEST
- Confirm the Inverter System Controller (ISC) was the only module to fail.
Was the Inverter System Controller (ISC) the only module to fail?
Yes GO to BN5 No DIAGNOSE the network concern. REFER to: Communications Network . - BN5 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) B+ CIRCUIT FOR VOLTAGE
- Ignition OFF.
- Disconnect Inverter System Controller (ISC) C1458A.
- Ignition ON.
Is the voltage greater than 10.5 volts?
Yes GO to BN6 No REPAIR the circuit. - BN6 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) VPWR CIRCUITS FOR VOLTAGE
- Ignition OFF.
- Connect a 5A fused jumper between:
Positive Lead Measurement / Action Negative Lead C1458A-K3 Ground
- Ignition ON.
- Measure and record:
Positive Lead Measurement / Action Negative Lead C1458A-L2 Ground C1458A-M2 Ground
Are the voltages greater than 10.5 volts?
Yes GO to BN7 No REPAIR the circuit. - BN7 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) GROUND CIRCUITS FOR AN OPEN
- Ignition OFF.
- Measure and record:
Positive Lead Measurement / Action Negative Lead C1458A-L4 Ground C1458A-M4 Ground
Are the resistances less than 5 ohms?
Yes DIAGNOSE the network concern. REFER to: Communications Network . No REPAIR the open circuit.