Tighten the bolts on the front axle support
- Replace screws (1)
, (2)
and (3)
.
Parts: Screws
- Tighten down screws (3) .
TIGHTENING TORQUES SPECIFICATION
| Front axle carrier to body, front | ||
|---|---|---|
| M12 Replace screws. |
Snug torque | 108 Nm |
| Angle of rotation | 45° | |
- Tighten down screws (2) .
TIGHTENING TORQUES SPECIFICATION
| Front axle support to center of body | ||
|---|---|---|
| M12 Replace screws. |
Snug torque | 108 Nm |
| Angle of rotation | 45° | |
- Tighten down screws (1) .
TIGHTENING TORQUES SPECIFICATION
| Front axle carrier to body, rear | ||
|---|---|---|
| M14 Replace screws. |
Snug torque | 108 Nm |
| Angle of rotation | 45° | |
NOTE:
Perform the steps on the right and left side.
- Replace screws (1)
.
Parts: Screws
- Tighten down screws (1) .
TIGHTENING TORQUES SPECIFICATION
| Bottom bumper bracket on the front subframe. | ||
|---|---|---|
| M8x100 Replace screws. |
Tightening torque | 19 Nm |
Follow-up work
- Refer to SECURING THE SWIVEL BEARING, TOP LEFT AND RIGHT .
- Refer to REMOVING THE MOBILE LIFTING TABLE .
- Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
- Refer to ATTACHING THE THERMOSTAT OR TRANSMISSION OIL COOLER LINE ON THE FRONT SUBFRAME .
- Refer to INSTALLING THE UNIVERSAL JOINT .
- Refer to ATTACHING THE CABLE OF THE WHEEL RPM SENSOR ON THE LEFT AND RIGHT .
- Refer to SECURING CABLES ON VERTICAL ACCELERATION SENSOR ON RIGHT AND LEFT .
- Refer to ATTACHING THE BRAKE CALIPER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE ANTI-ROLL BAR .
- Refer to INSTALLING THE LEFT-HAND AND RIGHT-HAND CRASH LEVER .
- Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- Refer to INSTALLING THE REINFORCEMENT STRUT ON THE RIGHT ENGINE MOUNT .
- Refer to INSTALLING THE OUTPUT SHAFTS .
- Refer to DRAIN/TOPPING UP THE FRONT AXLE TRANSMISSION OIL .
- Refer to INSTALLING THE LEFT AND RIGHT SPRING STRUT HOLDER .
- Refer to REMOVING ENGINE BRIDGE .
- Refer to INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 1 .
- Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
- Refer to TIGHTENING THE FRONT-END STRUT ON THE RIGHT .
- Refer to INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE FRONT HOOD SEAL .
- Refer to INSTALLING THE SUPPORT BRIDGE .
- Refer to INSTALLING CONDUIT ON BANK 2 .
- Refer to INSTALLING CONDUIT ON BANK 1 .
- Refer to INSTALLING EXPANSION TANK FOR THE CHARGE AIR COOLER .
- Refer to INSTALLING COOLANT EXPANSION TANK .
- Refer to INSTALLING THE HOLDER OF THE DME CONTROL UNIT FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE PRIMARY OXYGEN SENSOR FOR CYLINDERS 1 TO 4 .
- Refer to INSTALLING THE COVER PANEL OF THE SLAVE DME CONTROL UNIT .
- Refer to INSTALLING THE COVER PANEL OF THE MASTER DME CONTROL UNIT .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to FASTENING THE FRONT LEFT AND RIGHT SPRING STRUT .
- Refer to INSTALLING THE SIDE SEALING ON THE LEFT AND RIGHT FOR THE HOOD .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to ACTIVATING VEHICLE ELECTRICAL SYSTEM .
- Refer to PLACING THE BRAKE PADS ON THE BRAKE DISK/PUTTING THEM INTO OPERATION .