Replacing the engine block

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW X2, 2022 BMW X2, 2021 BMW X2, 2020 BMW X2, and 2019 BMW X2. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: Component with heavy weight .
Injury hazard!

Note component's center of gravity.
Support component using a jack.
Secure component against falling off the jack.

NOTE: TECHNICAL INFORMATION
When replacing the engine block, the engine number must be transferred to the new engine block (documentation required).

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

Preliminary work

Refer to REMOVING THE ENGINE .
Refer to REMOVING TRANSFER BOX (VTG) .
Refer to REMOVING THE ENGINE FROM THE AUTOMATIC TRANSMISSION .
Refer to INSTALLING THE ENGINE ON THE ASSEMBLY JIG .
Refer to IF INSTALLED: PARTIALLY REMOVING THE ENGINE VENTILATION LINE .
Refer to REMOVING CLEAN AIR PIPE .
Refer to REMOVING IGNITION COILS .
Refer to REMOVING ALL SPARK PLUGS .
Refer to REMOVING THE HIGH PRESSURE LINE BETWEEN THE RAIL AND THE HIGH PRESSURE PUMP .
Refer to REMOVING FUEL DELIVERY LINE .
Refer to REMOVING HIGH PRESSURE PUMP .
Refer to REMOVING INJECTORS .
Refer to REMOVING THE LAMBDA OXYGEN SENSOR .
Refer to REMOVING THE OXYGEN SENSOR MONITOR .
Refer to REMOVING THE CATALYTIC CONVERTER (ENGINE REMOVED) .
Refer to REMOVING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
Refer to REMOVING EXHAUST TURBOCHARGER .
Refer to REMOVING THE OIL FEED LINE FOR THE EXHAUST TURBOCHARGER .
Refer to REMOVING COOLANT FEED LINE .
Refer to REMOVING TANK VENT VALVE .
Refer to REMOVING THE INTAKE PLENUM .
Refer to REMOVING THE SERVOMOTOR FOR THE ECCENTRIC SHAFT .
Refer to REMOVING THE DRIVE BELT FOR ALTERNATOR .
Refer to REMOVING AIR CONDITIONING COMPRESSOR .
Refer to REMOVING THE ALTERNATOR .
Refer to REMOVING THE COOLANT LINE BETWEEN THE COOLANT PUMP AND CYLINDER HEAD .
Refer to REMOVING THE COMPONENT CARRIER .
Refer to REMOVING FULL-FLOW OIL FILTER .
Refer to REMOVING HEAT MANAGEMENT MODULE .
Refer to REMOVING THE KNOCK SENSOR OF CYLINDERS 1 TO 2 .
Refer to REMOVING THE KNOCK SENSOR OF CYLINDERS 3 TO 4 .
Refer to REMOVING COOLANT TEMPERATURE SENSOR .
Refer to REMOVING TEMPERATURE SENSOR ON CRANKCASE .
Refer to REMOVING THE OIL PRESSURE SWITCH .
Refer to REMOVING HYDRAULIC VALVE .
Refer to REMOVING THE ENGINE WIRING HARNESS FOR SENSOR SYSTEM 1 .
Refer to REMOVING ENGINE WIRING HARNESS FOR SENSOR SYSTEM 2 .
Refer to REMOVING BOTH ACTUATORS .
Refer to REMOVING THE CYLINDER HEAD COVER .
Refer to BLOCKING ENGINE IN TDC FIRING POSITION .
Refer to REMOVING CHAIN TENSIONER .
Refer to RELEASING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to RELEASING VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to REMOVING THE VANOS CENTRAL VALVE OF THE INTAKE CAMSHAFT ADJUSTER .
Refer to REMOVING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to REMOVING INTAKE ADJUSTER .
Refer to REMOVING EXHAUST CAMSHAFT ADJUSTER .
Refer to REMOVING THE TEST GAUGES FOR SECURING THE CAMSHAFTS .
Refer to REMOVING THE CYLINDER HEAD .
Refer to REMOVING THE CYLINDER HEAD GASKET .
Refer to REMOVING THE VIBRATION DAMPER .
Refer to REMOVING FLYWHEEL (AUTOMATIC TRANSMISSION) .
Refer to REMOVING OIL SUMP .
Refer to REMOVING REAR TIMING CASE COVER .
Refer to REMOVING TIMING CHAIN .
Refer to REMOVING OIL VACUUM PUMP .
Refer to REMOVING THE OIL DEFLECTOR .
Refer to INSTALLING THE ENIGINE BLOCK ON THE ASSEMBLY JIG .

NOTE: TECHNICAL INFORMATION
When replacing the engine block, the engine number must be transferred to the new engine block (documentation required).

NOTE: Schematic diagram is for example purposes. Some parts may differ in certain details.

Transfer engine number (1) to engine block (2) .

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE OIL DEFLECTOR .
Refer to INSTALLING THE OIL VACUUM PUMP .
Refer to INSTALLING TIMING CHAIN .
Refer to INSTALLING THE REAR TIMING CASE COVER .
Refer to REFITTING SUMP .
Refer to INSTALLING FLYWHEEL (AUTOMATIC TRANSMISSION) .
Refer to INSTALLING THE FRONT CRANKSHAFT SEAL .
Refer to INSTALLING THE VIBRATION DAMPER .
Refer to INSTALLING TEMPERATURE SENSOR ON THE CRANKCASE .
Refer to INSTALLING THE OIL PRESSURE SWITCH .
Refer to INSTALLING COOLANT TEMPERATURE SENSOR .
Refer to INSTALLING THE KNOCK SENSOR AT CYLINDERS 1 TO 2 .
Refer to INSTALLING THE KNOCK SENSOR AT CYLINDERS 3 TO 4 .
Refer to INSTALLING HYDRAULIC VALVE .
Refer to INSTALLING FULL-FLOW OIL FILTER .
Refer to INSTALLING HEAT MANAGEMENT MODULE .
Refer to INSTALLING THE COMPONENT CARRIER .
Refer to INSTALLING ALTERNATOR .
Refer to INSTALLING AIR CONDITIONING COMPRESSOR .
Refer to INSTALLING THE DRIVE BELT FOR THE ALTERNATOR .
Refer to SEALING THE OIL DUCT .
Refer to CLEANING SEALING SURFACES .
Refer to REPLACING CYLINDER HEAD GASKET .
Refer to INSTALLING THE CYLINDER HEAD .
Refer to ADJUSTING THE CAMSHAFTS WITH THE SPECIAL TOOL .
Refer to BLOCKING THE CRANKSHAFT IN HE TDC FIRING POSITION OF CYLINDER 1 .
Refer to INSTALLING EXHAUST CAMSHAFT ADJUSTER .
Refer to INSTALLING THE INTAKE ADJUSTER .
Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to PRE-TENSIONING THE TIMING CHAIN WITH THE SPECIAL TOOL .
Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to DISASSEMBLING ALL SPECIAL TOOLS .
Refer to INSTALLING CHAIN TENSIONER .
Refer to CHECKING THE TIMINGS OF THE CAMSHAFT .
Refer to INSTALLING THE COOLANT LINE BETWEEN THE COOLANT PUMP AND CYLINDER HEAD .
Refer to INSTALLING THE SERVOMOTOR FOR THE ECCENTRIC SHAFT .
Refer to INSTALLING THE ENGINE WIRING HARNESS FOR THE SENSOR SYSTEM 1 .
Refer to INSTALLING THE ENGINE WIRING HARNESS FOR SENSOR SYSTEM 2 .
Refer to INSTALLING THE INTAKE PLENUM .
Refer to INSTALLING THE TANK VENT VALVE .
Refer to INSTALLING THE OIL FEED LINE FOR THE EXHAUST TURBOCHARGER .
Refer to INSTALLING COOLANT FEED LINE .
Refer to PREPARING FOR THE INSTALLATION OF THE EXHAUST TURBOCHARGER .
Refer to INSTALLING EXHAUST TURBOCHARGER .
Refer to INSTALLING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
Refer to INSTALLING THE CATALYTIC CONVERTER (ENGINE REMOVED) .
Refer to INSTALLING CYLINDER HEAD COVER .
Refer to INSTALLING BOTH ACTUATORS .
Refer to PREPARING THE INJECTORS FOR INSTALLATION .
Refer to INSTALLING INJECTORS .
Refer to PREPARING FOR THE INSTALLATION OF THE HIGH PRESSURE PUMP .
Refer to INSTALLING HIGH PRESSURE PUMP .
Refer to INSTALLING FUEL DELIVERY LINE .
Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE RAIL AND THE HIGH-PRESSURE PUMP .
Refer to INSTALLING ALL SPARK PLUGS .
Refer to INSTALLING THE IGNITION COILS .
Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
Refer to INSTALLING LAMBDA OXYGEN SENSOR .
Refer to PREPARING FOR THE INSTALLATION OF THE CLEAN AIR PIPE .
Refer to INSTALLING CLEAN AIR PIPE .
Refer to IF INSTALLED: PARTIALLY INSTALLING ENGINE VENTILATION LINE .
Refer to REMOVING THE ENGINE FROM THE ASSEMBLY JIG .
Refer to INSTALLING ENGINE ON AUTOMATIC TRANSMISSION .
Refer to INSTALLING THE TRANSFER BOX (VTG) .
Refer to INSTALLING ENGINE .