Heating, Air Conditioning And Ventilation -- Lancer
- General Description
- General Specifications
- Service Specifications
- Lubricants
- Service Precautions
- Manual A/C Diagnosis
- Introduction To Heater, A/C And Ventilation Diagnosis
- Heater, A/C And Ventilation Diagnostic Troubleshooting Strategy
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1000: Control panel communication error
- DTC B1000: Control Panel Communication Error
- DTC B1003: Mode Dial SW Error
- DTC B1003: Mode Dial SW Error
- DTC B1018: Temperature Control Dial SW Error
- DTC B1018: Temperature Control Dial SW Error
- DTC B1021: Fan Dial SW Error
- DTC B1021: Fan Dial SW Error
- DTC B1031, B1032: Air Thermo Sensor System
- DTC B1031, B1032: Air Thermo Sensor System
- DTC B1034, B1035: Ambient air temperature Sensor System
- DTC B1079: Refrigerant Leaks
- DTC B2214: Control Panel Failure
- DTC B2214: Control Panel Failure
- DTC B223B: Control Panel Improperly Assembled
- DTC B223B: Control Panel Improperly Assembled
- DTC U1415: Coding Not Completed
- DTC U0019: Bus Off (CAN1)
- DTC U0141: ETACS-ECU Time-out
- DTC U0151: SRS-ECU Time-out
- DTC U0154: Occupant classification ECU time out
- DTC U0155: Combination meter Time-out
- DTC U0168: WCM Time-out
- DTC U0184: Audio Time-out
- DTC U0195: Satellite radio tuner CAN timeout
- DTC U0197: Hands Free Module Time-out
- DTC B1000: Control panel communication error
- SYMPTOM CHART <Vehicles without A/C>
- Symptom Procedures
- INSPECTION PROCEDURE 1: Malfunction of the heater control unit Power Supply System.
- INSPECTION PROCEDURE 2: Blower fan and motor do not turn.
- INSPECTION PROCEDURE 3: Blower air amount cannot be changed.
- INSPECTION PROCEDURE 4: Outside/inside air changeover is not possible
- INSPECTION PROCEDURE 5: A/C outlet air temperature does not increase
- INSPECTION PROCEDURE 6: Air outlet vent cannot be changed.
- INSPECTION PROCEDURE 7: Rear window defogger does not operate.
- INSPECTION PROCEDURE 8: Blower motor power supply system.
- INSPECTION PROCEDURE 1: Malfunction of the heater control unit Power Supply System.
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When the A/C is Operation, Temperature Inside the Passenger Compartment does not Decrease (Cool Air is not Emitted)
- INSPECTION PROCEDURE 2: Malfunction of the A/C-ECU Power Supply System
- INSPECTION PROCEDURE 3: The Compressor does not Work
- INSPECTION PROCEDURE 4: Blower Fan and Motor do not Turn
- INSPECTION PROCEDURE 5: Blower Air Amount cannot be Changed
- INSPECTION PROCEDURE 6: Outside/Inside Air Changeover is not possible
- INSPECTION PROCEDURE 7: A/C Outlet Air Temperature does not Increase
- INSPECTION PROCEDURE 8: Air Outlet Vent cannot be Changed
- INSPECTION PROCEDURE 9: Rear window defogger does not operate
- INSPECTION PROCEDURE 10: Blower Motor power supply system
- Data List Reference Table
- Actuator Test Reference
- Check At A/C-Ecu Terminal
- Special Tools
- On-Vehicle Service
- Heater Control Unit
- Heater Unit And Blower Assembly
- Motors And Transistor
- Ambient Air Temperature Sensor
- A/C-Ecu
- COMPRESSOR ASSEMBLY
- Compressor Assembly And Tension Pulley
- Condenser Assembly
- Refrigerant Line
- Ducts
- Ventilators