Chassis Electrical - 3 Of 5
- Component Index
- Radio And Cd Player
- General Information
- Special Tools
- Diagnosis
- Introduction To Audio System Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnosis Function
- Data List Reference Table
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC U0019: Bus off (CAN-B)
- DTC U0141: ETACS CAN timeout
- DTC U0151: SRS-ABG CAN timeout
- DTC U0154: OCM CAN timeout
- DTC U0155: Meter CAN timeout
- DTC U0164: A/C CAN timeout
- DTC U0168: WCM CAN timeout
- DTC U0195: Satellite radio CAN timeout
- DTC U0197: Hands free module CAN timeout
- DTC U1415: Coding not completed/Data fail
- DTC B2420: Power integrated circuit
- DTC B2421: Radio tuner
- DTC B2423: 6CD player error
- DTC B2424: CD player error
- Code No. B2450 Switch panel communication
- DTC B2451: Audio panel type error
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: Power is not turned ON when the power switch is turned ON.
- Inspection Procedure 2: No sound is heard. < Vehicles with audio amplifier >
- Inspection Procedure 3: No sound is heard from one of the speakers. < Vehicles without audio amplifier >
- Inspection Procedure 3: No sound is heard from one of the speakers. < Vehicles with audio amplifier >
- Comments On Trouble Symptom
- Inspection Procedure 4: The sound of external input are not played. < Vehicles without rear display unit (with audio adapter) >
- Inspection Procedure 5: Noise is present while moving (AM).
- Inspection Procedure 6: Noise is present while moving (FM).
- Inspection Procedure 7: Sound mixed with noise, only at night (AM).
- Inspection Procedure 8: Noise is overpowering both AM and FM.
- Inspection Procedure 9: Excessive noise on AM and FM.
- Inspection Procedure 10: Noise is detected with engine running.
- INSPECTION PROCEDURE 11: Noise appears during vibration or shocks.
- Inspection Procedure 12: Noise is present while moving (FM).
- Inspection Procedure 13: Constant noise.
- Inspection Procedure 14: No reception (AM).
- Inspection Procedure 15: Poor reception.
- Inspection Procedure 16: Distortion on AM and/or FM.
- INSPECTION PROCEDURE 17: Distortion on FM only.
- Inspection Procedure 18: Auto select function inoperative, too few automatic stations are selected.
- Inspection Procedure 19: Preset stations are erased.
- Inspection Procedure 20: CD cannot be Inserted.
- Inspection Procedure 21: No sound. (CD only)
- inspection procedure 22: CD sound skips.
- Inspection Procedure 23: Sound quality is poor.
- Inspection Procedure 24: CD cannot be ejected.
- On-Vehicle Service
- Removal And Installation
- Inspection
- MMCS
- General Information
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Precautions On Servicing MMCS
- Service Mode
- How To Initiate The Service Mode
- How To Terminate The Service Mode
- Vehicle Signal Check
- Monitor Check
- Network And Connect Line Check
- Speaker Check
- Versions Indication
- Sensor Check
- NG Code Reference Table For Sensor Check
- Touch Switch Confirmation
- Memory Initialization
- Can Communication Confirmation
- Can Box Unit-Connected Equipment Reference Table
- Versions Log Information
- Each Log Information: Factor Code Table
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B2226: AND error
- DTC B2240: Communication error with CAN Box
- DTC B2477: VIN not programmed
- DTC U0019: Bus off (CAN-B)
- DTC U0141: ETACS CAN timeout
- DTC U0151: SRS-AGB CAN timeout
- DTC U0154: OCM CAN timeout
- DTC U0155: Meter CAN timeout
- DTC U0164: A/C CAN timeout
- DTC U0168: WCM CAN timeout
- DTC U0195: Satellite radio CAN timeout
- DTC U0197: Hands free module CAN timeout
- DTC U1415: Coding not completed/Data fail
- DTC U1417: Implausible coding data
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: No navigation screen is displayed.
- Inspection Procedure 2: No sound is heard. < Vehicles without audio amplifier >
- Inspection Procedure 2: No sound is heard. < Vehicles with audio amplifier >
- Inspection Procedure 3: No sound is heard from one of the speakers. < Vehicles without audio amplifier >
- Inspection Procedure 3: No sound is heard from one of the speakers. < Vehicles with audio amplifier >
- Inspection Procedure 4: The navigation system can be operated while the vehicle is driven.
- Inspection Procedure 5: The screen is not normal in the navigation mode. (The displayed position of the vehicle mark deviates).
- Inspection Procedure 6: Poor reception.
- Inspection Procedure 7: GPS signal can not be received.
- Inspection Procedure 8: CD (compact disk)/DVD (Video Disk) cannot be played.
- Inspection Procedure 9: Image of a DVD (Video Disk) is played, but no sound is played.
- Inspection Procedure 10: Sound of a DVD (Video Disk) can be played, but no image is played.
- Inspection Procedure 11: The picture and sound of external input are not played.
- Inspection Procedure 12: Check the CAN box unit power supply circuit.
- ETACS Function Customization Function
- Removal And Installation
- Inspection
- Steering Wheel Audio Remote Control Switch
- General Information
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Trouble Symptom Chart
- Symptom Procedures
- Removal And Installation
- Steering Wheel Audio Remote Control Switch Inspection