Section 4156 (Engine Assembly And Cylinder Head - Repair - F12)
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2018 BMW M6, 2018 BMW 650i xDrive, 2018 BMW 650i, 2018 BMW 640i xDrive, and 2018 BMW 640i. However, it is still accessible from the selected car via links, so may be relevant.
- Engine Assembly
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 00 Safety instructions for handling oil
- 11 00 039 Checking compression of all cylinders (N55)
- 11 00 000 Differences among basic engine versions (N63/S63)
- Engine Identification
- 11 00 300 Engine oil consumption measurement
- 11..... Equipment recoding special tool number of the transverse member for fixing the engine in the installation location
- 11 00... Handling components after flood damage
- 11 00 Mounting engine on assembly stand (N55)
- 11 00 Mounting Engine On Assembly Stand (N63)
- 11 00 Mounting Engine On Assembly Stand (N63O1)
- 11 00 Mounting Engine On Assembly Stand (S63T)
- 11 00... Overview of consumables
- 11 00 050 Removing and installing engine (N55)
- 11 00 598 Removing and installing engine on front axle (S63T 0) with GS7D36SG transmission
- 11 00 598 Removing and installing engine on front axle (S63T 0) with GS6-53BZ transmission
- 11 00 598 Removing and installing engine on front axle (N63O1) with GA6HP26Z all-wheel drive vehicle transmission
- 11 00 598 Removing and installing engine on front axle (N63O1) with GA8HP70Z all-wheel drive vehicle transmission
- 11 00 598 Removing and installing engine on front axle (N63O1) with GA8HP70Z transmission
- 11 00 598 Removing and installing engine on front axle (N63O1) with manual gearbox
- 11 00 050 Removing and installing/replacing engine (N63)
- 12 00 Removing and installing/replacing ignition coil cover (N55)
- 11 00 Removing and installing/replacing the acoustic cover (N63 B44 O 0/1)
- 11 00 670 Securing engine in installation position (N55)
- 11 00 670 Securing engine in installation position (N63)
- 11 00 670 Securing engine in installation position (N63O1)
- 11 00 670 Securing engine in installation position (S63)
- 11 00... Service - engine oil (N55)
- 11 00... Service - engine oil (N63)
- 11 00... Service - engine oil (N63O1)
- 11 00... Service engine oil (S63T 0)
- 31 10 001 Completely removing and installing front axle with engine and transmission (S63T0, DKG)
- 31 10 001 Completely removing and installing the front axle with engine and transmission (S63T0, manual gearbox)
- Cylinder Head
- 11 12 000 Removing and installing/sealing cylinder head cover (N55)
- 11 12 040 Removing and installing all ignition coils and injector wells (N55)
- 11 12 100 Removing and installing cylinder head (N55)
- 11 12 101 Replacing cylinder head gasket (N55)
- 11 12 719 Resurfacing cylinder head lower face (N55)
- 11 12 729 Checking cylinder head for water leaks (N55)
- 11 12 005 Removing and installing/sealing left cylinder head cover (N63)
- 11 12 006 Removing and installing/sealing right cylinder head cover (N63)
- 11 12 105 Removing and installing left cylinder head (N63)
- 11 12 106 Removing and installing right cylinder head (N63)
- 11 12 112 Replacing both cylinder head gaskets (N63)
- 11 12 719 Grinding cylinder head sealing surface (N63)
- 11 12 729 Checking cylinder head for watertightness (N63)
- 11 15 140 Replace oil separator (N63O0)
- 11 12 005 Removing and installing/sealing left cylinder head cover (N63O1)
- 11 12 006 Removing and installing/sealing right cylinder head cover (N63O1)
- 11 12 105 Removing and installing left cylinder head (N63O1)
- 11 12 106 Removing and installing right cylinder head (N63O1)
- 11 12 112 Replacing both cylinder head gaskets (N63O1)
- 11 15 140 Replace oil separator (N63O1)
- 11 12 719 Grinding cylinder head lower face (N63O1)
- 11 12 729 Checking cylinder head on watertightness (N63O1)
- 11 12 005 Removing and installing/sealing left cylinder head cover (S63T 0)
- 11 12 006 Removing and installing/sealing right cylinder head cover (S63T 0)
- 11 12 090 Removing engine cover (S63T 0)
- 11 12 105 Removing and installing left cylinder head (S63T 0)
- 11 12 106 Removing and installing right cylinder head (S63T 0)
- 11 12 112 Replacing both cylinder head gaskets (S63T 0)
- 11 12 719 Surface grinding cylinder head lower face (S63T 0)
- 11 12 729 Checking cylinder head on watertightness (S63T 0)