Section 365 (Engine Timing - 253 Chassis)
WARNING: This page is about a different car, the 2023 Mercedes-Benz GLC300, 2022 Mercedes-Benz GLC300, 2021 Mercedes-Benz GLC300, 2020 Mercedes-Benz GLC350e, and 2020 Mercedes-Benz GLC300. However, it is still accessible from the selected car via links, so may be relevant.
- General Information
- General Notes: Passenger Cars: Engine Timing - AH05.00-Z-9999AZ
- General Information On Checking Camshafts And Bearing Points Of Camshafts - AH05.20-P-1000-09SZ
- (Marking Of Camshaft Bearing Caps - AH05.20-Z-6992-01KOA)
- General Information On Checking Valves, Valve Seats And Valve Guides - AH05.30-P-1000-02SZ
- Basic Knowledge
- Safety Precautions
- Testing & Repair
- Check Hydraulic Valve Clearance Compensating Elements
- Remove/Install Hydraulic Valve Clearance Compensating Elements
- Disconnect Timing Chain
- Rivet Timing Chain
- Draw In Timing Chain
- Replace Timing Chain
- Remove/Install Timing Chain Tensioner
- Remove/Install Timing Chain Tensioning Rail
- Remove/Install Timing Chain Lower Slide Rail - AR05.10-P-8420MRI
- Remove/Install Timing Chain Upper Slide Rail - AR05.10-P-8421MRI
- Remove/Install Timing Chain Upper And Lower Slide Rails - AR05.10-P-8480MRA
- Check Basic Position Of Camshafts
- Set Basic Position Of Camshafts
- Remove/Install Intake Camshaft Lift Solenoid - AR05.20-P-6560MRI
- Remove/Install Camshafts
- Remove/Install Camshaft Positioner
- Remove/Install Camshaft Solenoid - AR05.20-P-7295MRA
- Remove/Install Intake Camshaft Adjustment Solenoid - AR05.20-P-7305MRI
- Remove/Install Exhaust Camshaft Adjustment Solenoid - AR05.20-P-7306MRI
- Remove/Install Valve Springs - AR05.30-P-3021MRI
- Replace Valve Stem Seals
- Remove/Install Valve Springs And/Or Valve Stem Seals - AR05.30-P-3500MRA
- Remove/Install Valve Stem Seals - AR05.30-P-3501MRI
- Remove/Install Valves
- Test & Adjustment Values
- Torque Specifications
- Special Tools
- 000 589 10 68 00 Cylinder Brush - WS05.00-P-0002C
- 270 589 01 07 00 Socket Wrench Bit - WS05.00-P-0017C
- 270 589 00 61 00 Holding Device - WS05.00-P-0019C
- 115 589 20 33 00 Puller - WS05.00-P-0079B
- 116 589 06 63 00 Magnetic Rod - WS05.00-P-0088B
- 604 589 00 43 00 Drift - WS05.00-P-0114B
- 276 589 00 39 00 Rivet Press Tool - WS05.00-P-0115C
- 606 589 00 37 00 Pliers - WS05.00-P-0116B
- 270 589 01 33 00 Puller - WS05.00-P-0147B
- 177 589 00 09 00 Socket Wrench Bit - WS05.00-P-0148C
- 605 589 00 33 02 Puller Bolt - WS05.00-P-0154-01B
- 605 589 00 33 00 Puller - WS05.00-P-0154B
- 602 589 00 98 00 Case - WS05.00-P-0158C
- 602 589 02 33 00 Chain Separating Tool - WS05.00-P-0159C
- 602 589 00 39 00 Riveting Tool - WS05.00-P-0162C
- 270 589 01 61 00 Holding Device - WS05.00-P-0166C
- 602 589 02 40 00 Assembly Links - WS05.00-P-0171C
- 177 589 00 03 00 Box Wrench - WS05.00-P-0174B
- 271 589 00 59 00 Assembly Tool - WS05.00-P-0202C
- 271 589 09 63 00 Assembly Element - WS05.00-P-0228B
- 272 589 00 61 00 Depressor - WS05.00-P-0233B
- 640 589 00 61 00 Depressor - WS05.00-P-0236B
- 642 589 00 33 00 Riveting Tool - WS05.00-P-0260C
- 271 589 00 10 00 Socket - WS05.00-P-0268B
- 111 589 25 61 03 Lever Handle - WS05.00-P-3137-03C
- 111 589 25 61 05 Detent Depressor - WS05.00-P-3137-05C
- 111 589 25 61 12 Fixing Bracket - WS05.00-P-3137-12C
- 111 589 25 61 19 Grid - WS05.00-P-3137-19C
- 111 589 25 61 00 Valve Assembly Tools Kit - WS05.00-P-3137BA
- 116 589 20 33 00 Impact Extractor - WS05.00-Z-0089KOB
- 210 589 00 40 00 Magnetic Pin - WS05.00-Z-0155KOP