Section 1663 (Automatic Transmission - 6L45/6L50/6L80/6L90 - Repair Instructions - Off Vehicle)
WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
- Repair Instructions - Off Vehicle
- Torque Converter Removal and Holding Fixture Installation
- Case Extension Assembly Removal
- Transmission Fluid Pan, Filter and Electrical Connector Passage Sleeve Removal
- Control Valve Body Assembly Removal
- Torque Converter Housing with Fluid Pump Removal
- 1-2-3-4 and 3-5 Reverse Clutch Assembly and 4-5-6 Clutch Assembly Removal (6L50/80/90)
- Center Support, Output Carrier and Output Shaft Removal (6L80/6L90)
- Manual Shift Shaft and Parking System Components Overhaul (6L80/6L90)
- Manual Shift Shaft Seal Replacement
- Output Shaft Seal Replacement (AWD Models Only)
- Case Inspection
- Output Shaft Disassemble
- Output Shaft Assemble (6L50/80/90)
- Output Carrier Assembly Overhaul (6L80)
- Output Carrier Assembly Overhaul (6L90)
- Output Carrier to Output Shaft Assemble (6L80/6L90)
- 2-6 Clutch Overhaul
- Low and Reverse Clutch Overhaul
- Low and Reverse Clutch Backing Plate Retaining Ring Measurement
- 4-5-6 Clutch Dampener Overhaul (6L50/80/90)
- 4-5-6 Clutch Overhaul
- 4-5-6 Clutch Backing Plate Retaining Ring Measurement
- 1-2-3-4 and 3-5 Reverse Clutch Overhaul
- 1-2-3-4 and 3-5 Reverse Clutch Plates Removal
- 1-2-3-4 Clutch Piston Removal
- 3-5 Reverse Clutch Piston Removal
- 3-5 Reverse Clutch Air Bleed Inspection (6L80/6L90)
- 1-2-3-4 and 3-5 Reverse Clutch Piston Seals Replacement
- 3-5 Reverse Clutch Piston Installation
- 1-2-3-4 Clutch Piston Installation
- 1-2-3-4 Clutch Plate Installation
- 3-5 and Reverse Clutch Plate Installation
- 1-2-3-4 and 3-5 Reverse Clutch Bearing Assembly Replacement
- 1-2-3-4 Clutch Backing Plate Retaining Ring Measurement
- 3-5 Reverse Clutch Backing Plate Retaining Ring Measurement (6L80/6L90)
- Torque Converter Housing with Fluid Pump Disassemble
- Fluid Pump Cover Cleaning and Inspection
- 1-2-3-4 and 3-5 Reverse Clutch Fluid Seal Ring Installation (6L80/90)
- Torque Converter Housing Cleaning and Inspection
- Torque Converter Fluid Seal Replacement
- Transmission Fluid Cooler Pipe Seal Replacement
- Fluid Pump Selective Measurement
- Torque Converter Housing with Fluid Pump Assemble
- Fluid Pump Cover Installation
- Control Valve Body Assembly Disassemble
- Control Valve Lower Body Assembly Cleaning and Inspection
- Control Valve Upper Body Assembly Cleaning and Inspection
- Control Valve Body Assembly Assemble
- Upper to Lower Control Valve Body Assembly Assemble
- Filter Plate Installation
- Control Solenoid Valve Assembly Installation
- Manual Shift Shaft Position Switch Installation
- Valve Body, Control Solenoid Torque Sequence
- Control Solenoid Valve Assembly Contact Gap Inspection
- Input and Output Speed Sensor Assembly Installation
- Center Support, Output Carrier and Output Shaft Installation (6L80/6L90)
- 1-2-3-4 and 3-5 Reverse Clutch Assembly and 4-5-6 Clutch Assembly Installation (6L50/80/90)
- Torque Converter Housing with Fluid Pump Installation
- Propeller Shaft Front Slip Yoke Oil Seal Replacement
- Control Valve Body Assembly Installation
- Automatic Transmission Electrical Connector Passage Sleeve Installation
- Fluid Filter and Manual Shift Detent Assembly Installation
- Transmission Fluid Pan Installation
- Case Extension Assembly Installation
- Torque Converter Installation and Holding Fixture Removal