Section 358 (Rear Axle - Repair)
WARNING: This page is about a different car, the 2013 BMW Z4, 2012 BMW Z4, 2011 BMW Z4, 2010 BMW Z4, and 2009 BMW Z4. However, it is still accessible from the selected car via links, so may be relevant.
- 3300 General
- 00 Danger of poisoning if oil is ingested/absorbed through the skin
- 33 00... Information on replacing shock absorbers
- 64 00 000 Information on using cleaning agent/paints (personal protection equipment)
- 41 00... Installation solution for straight shank/hexagon rivet nut
- 33 00... Instructions (chassis components made of aluminum)
- 33 00... Notes on repairing threads
- 33 32... Overview of control arms with rubber mounts
- 33 31. Overview of rear axle carrier with rubber mounts
- 33 10... Overview of rear differential/output shafts
- 00...... Raising vehicle with trolley jack
- 33... Rear axle layout
- 33 00... Rear axle: wheel/chassis alignment check must be carried out after the following work
- 51 47 491 Removing and installing/replacing rear underbody protection
- 41 00... Repair solution for straight shank/hexagon rivet nut
- 00 Risk of injury if oil comes into contact with eyes and skin
- 00 Safety instructions for handling oil
- 3310 Final Drive
- 3311 Final Drive With Cover
- 33 31 025 Removing and installing/replacing vibration absorber on side member
- 33 11 080 Replacing left drive flange on rear differential
- 33 11 021 Replacing radial shaft seal for drive flange on rear differential
- 33 11 271 Replacing rear cover gasket on rear differential
- 33 11... Replacing rear cover gasket on rear differential (188L)
- 33 11... Replacing rear cover gasket on rear differential (215 with lock)
- 33 11... Replacing rear cover gasket on rear differential (215L)
- 33 11 085 Replacing right drive flange on rear differential
- 33 11 140 Replacing shaft seal for left drive flange
- 33 11 145 Replacing shaft seal for right drive flange
- 3317 Final Drive Mounting
- 3321 Output Shafts
- 33 21... Pressing output shaft out of drive flange and drawing in (output shaft removed from rear axle final drive)
- 33 21 001 Removing and installing or replacing left output shaft
- 33 21 002 Removing and installing/replacing right output shaft
- 33 21 071 Replacing both gaiters on left and right of output shaft
- 33 21... Ribbed teeth
- 3331 Rear Sub-Frame
- 33 31 503 Lowering/raising rear axle carrier
- 33 31. Overview of rear axle carrier with rubber mounts
- 33 31 000 Removing and installing complete rear axle carrier
- 51 71 390 Removing and installing/replacing reinforcement plate on rear axle
- 33 31 025 Removing and installing/replacing vibration absorber on side member
- 33 31 011 Replacing rear axle carrier
- 3332 Control Arms And Struts
- 33 32... Overview of control arms with rubber mounts
- 33 32 077 Removing and installing/replacing top right control arm
- 33 32 086 Removing and installing/replacing bottom left control arm
- 33 32 087 Removing and installing/replacing bottom right control arm
- 33 32 160 Removing and installing/replacing compression strut for rear axle carrier
- 51 71 482 Removing and installing/replacing left or right tension strut
- 33 32 076 Removing and installing/replacing top left control arm
- 33 32 024 Replacing a ball joint in trailing arm
- 33 32 042 Replacing a rubber mount in trailing arm, front
- 33 32... Replacing bearing support for front trailing arm
- 33 32 021 Replacing left or right trailing arm
- 33 32 681 Replacing one rubber mount in lower control arm (control arm removed)
- 33 32 671 Replacing one rubber mount in the upper control arm (control arm removed)
- 33 32 044 Replacing one rubber mount in trailing arm for lower control arm
- 3333 Axle Mounting
- 3341 Wheel Bearings
- 3352 Shock Absorber
- 3353 Springs With Suspension
- 3355 Stabilizer Bar