Chassis Electrical - 5 Of 5
- Component Index
- ETACS
- General Information
- Special Tool
- Troubleshooting
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnosis Trouble Code Procedures
- DTC U0001: Bus off (CAN-C); DTC U0019: Bus off (CAN-B)
- DTC U0100: Engine control module CAN timeout
- DTC U0101: Transaxle control module CAN timeout
- DTC U0114: AWD-ECU CAN timeout
- DTC U0121: ABS-ECU or ASC-ECU CAN timeout
- DTC U0126: Steering wheel sensor CAN timeout
- DTC U0151: SRS-ECU CAN timeout
- DTC U0154: Occupant classification-ECU CAN timeout
- DTC U0155: Combination meter CAN timeout
- DTC U0164: A/C-ECU CAN timeout
- DTC U0168: WCM or KOS-ECU CAN timeout
- DTC U0184: Audio CAN timeout
- DTC U0195: Satellite radio tuner CAN timeout
- DTC U0197: Hands free module CAN timeout
- DTC U0245: CAN box unit CAN timeout
- DTC U1108: Excess CAN-B ECU Detection
- DTC U1120: Bus line (CAN-C) low input; DTC U1121: Bus line (CAN-C) high input
- DTC U0331: ECU internal error
- DTC B1761: Chassis number not recorded
- DTC B210A: +B power supply (low input); DTC B210B: +B power supply (high input)
- DTC B222C: Coding incomplete
- DTC B2206: Chassis number does not match
- DTC B2215: ECU internal error
- DTC B2353: Ignition power supply (low input); DTC B2354: Ignition power supply (high input)
- Data List Reference Table
- Trouble Symptom Chart
- Symptom Procedures
- Trouble Symptom Chart For Input Signal
- Input Signal Procedures
- Inspection Procedure 1: ETACS-ECU does not receive any signal from the ignition switch (ACC).
- Inspection Procedure 2: ETACS-ECU does not receive any signal from the ignition switch (IG1).
- Inspection Procedure 3: ETACS-ECU does not receive any signal from the key reminder switch.
- Inspection Procedure 4: ETACS-ECU does not receive any signal from the front door lock actuator.
- Inspection Procedure 5: ETACS-ECU does not receive any signal from the front door switch (LH).
- Inspection Procedure 6: ETACS-ECU does not receive any signal from the front door switch (RH).
- Inspection Procedure 7: ETACS-ECU does not receive any signal from the rear door switch (LH).
- Inspection Procedure 8: ETACS-ECU does not receive any signal from the rear door switch (RH).
- Inspection Procedure 9: ETACS-ECU does not receive any signal from the liftgate switch.
- Inspection Procedure 10: ETACS-ECU does not receive any signal from the hood switch.
- Inspection Procedure 11: ETACS-ECU does not receive any signal from the liftgate switch.
- Inspection Procedure 12: ETACS-ECU does not receive any signal from the hazard warning light switch.
- Inspection Procedure 13: ETACS-ECU does not receive any signal from the column switch signal.
- On-Vehicle Service
- ETACS-Ecu
- Theft Alarm
- General Information
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: The theft-alarm is not armed (the theft-alarm indicator does not illuminate).
- Inspection Procedure 2: The interior alarm does not work normally while the theft-alarm is triggered.
- Inspection Procedure 3: Theft-alarm horn does not sound while the theft-alarm system is triggered.
- Inspection Procedure 4: Horns do not sound while the theft-alarm system is triggered.
- On-Vehicle Service
- Removal And Installation
- Inspection
- Panic Alarm