Replacing the cylinder head (remounting components)
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW X2, 2022 BMW X2, 2021 BMW X2, 2020 BMW X2, and 2019 BMW X2. However, it is still accessible from the selected car via links, so may be relevant.
- Release the venting connector (1) at the cylinder head (3) .
- Release the coolant temperature sensor (2)
at the cylinder head (3)
.
- Replace the cylinder head (3)
.
Parts: Cylinder head
- Tighten venting connector (1)
on cylinder head (3)
.TIGHTENING TORQUE SPECIFICATIONS
Venting connector/special tool to cylinder head M10 18 Nm - Tighten the coolant temperature sensor (2) on the cylinder head (3) .
TIGHTENING TORQUE SPECIFICATIONS
| Coolant temperature sensor at cylinder head | ||
| Sensor | Tightening torque | 18 Nm |
Follow-up work
- Refer to INSTALLING THE CYLINDER HEAD .
- Refer to INSTALLING THE RIGHT ENGINE MOUNT .
- Refer to ADJUSTING THE CAMSHAFTS WITH THE SPECIAL TOOL .
- Refer to INSTALLING EXHAUST CAMSHAFT ADJUSTER .
- Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
- Refer to INSTALLING THE INTAKE ADJUSTER .
- Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
- Refer to PRE-TENSIONING THE TIMING CHAIN WITH THE SPECIAL TOOL .
- Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
- Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
- Refer to DISASSEMBLING ALL SPECIAL TOOLS .
- Refer to INSTALLING CHAIN TENSIONER .
- Refer to CHECKING THE TIMINGS OF THE CAMSHAFT .
- Refer to INSTALLING CYLINDER HEAD COVER .
- Refer to ROTATING THE CAM OF THE HIGH-PRESSURE PUMP DRIVE TO THE BDC POSITION .
- Refer to INSTALLING HIGH PRESSURE PUMP .
- Refer to INSTALLING BOTH ACTUATORS .
- Refer to PREPARING THE INJECTORS FOR INSTALLATION .
- Refer to INSTALLING INJECTORS .
- Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE RAIL AND THE HIGH-PRESSURE PUMP .
- Refer to INSTALLING ALL SPARK PLUGS .
- Refer to INSTALLING THE IGNITION COILS .
- Refer to CONNECTING COOLANT LINE .
- Refer to INSTALLING THE SERVOMOTOR FOR THE ECCENTRIC SHAFT .
- Refer to INSTALLING THE INTAKE PLENUM .
- Refer to INSTALLING THE TANK VENT VALVE .
- Refer to INSTALLING FAN COWL WITH ELECTRIC FAN .
- Refer to INSTALLING FRONT CROSS CONNECTION .
- Refer to PREPARING FOR THE INSTALLATION OF THE EXHAUST TURBOCHARGER .
- Refer to INSTALLING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
- Refer to INSTALLING CATALYTIC CONVERTER .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING THE CONNECTING SUPPORT ON THE TUNNEL AT FRONT AND REAR .
- Refer to INSTALLING THE CROSS-MEMBER WITH TORSION STRUTS .
- Refer to INSERTING FILLING HOSE OF THE WASHER FLUID RESERVOIR .
- Refer to PARTIALLY INSTALLING THE FRONT WHEEL ARCH COVER .
- Refer to INSTALLING THE FRONT RIGHT WHEEL ARCH COVER .
- Refer to INSTALLING THE FRONT RIGHT WHEEL .
- Refer to EVACUATE AND CHARGE CONDITIONING .
- Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
- Refer to INSTALLING LAMBDA OXYGEN SENSOR .
- Refer to INSTALLING RIGHT REAR SUSPENSION CROSS-BRACE .
- Refer to PREPARING FOR THE INSTALLATION OF THE CLEAN AIR PIPE .
- Refer to INSTALLING CLEAN AIR PIPE .
- Refer to IF INSTALLED: PARTIALLY INSTALLING ENGINE VENTILATION LINE .
- Refer to INSTALLING THE REAR BULKHEAD .
- Refer to INSTALLING INTAKE SILENCER HOUSING .
- Refer to INSTALLING THE INTAKE MANIFOLD FOR THE INTAKE FILTER HOUSING .
- Refer to INSTALLING THE UPPER FIREWALL COVER PANEL .
- Refer to INSTALLING THE STRUT BRACE .
- Refer to FILLING THE COOLANT CIRCUIT WITH THE VACUUM FILLING EQUIPMENT .
- Refer to CONNECTING THE BATTERY EARTH LEAD .
- Refer to AIR BLEEDING THE COOLANT CIRCUIT .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to CHECKING ENGINE OIL LEVEL .