Collision - Rear Wall & Rear End (213 Chassis)

• General Information
  • General Notes: Passenger Cars: Rear Wall And Rear End - Ah64.00-Z-9999AZ
• Testing & Repair
  • Separate Rear Wall Paneling - Ar64.10-P-1100-01LW
  • Prepare Rear Wall Paneling For Installation - Ar64.10-P-1100-03LW
  • Install Rear Wall Paneling - Ar64.10-P-1100-04LW
  • Remove/Install Rear Wall Paneling - Ar64.10-P-1100LW
  • Cut Off Rear Panel - Ar64.10-P-5746-01LWE
  • Prepare Rear Wall For Installation - Ar64.10-P-5746-02LWE
  • Install Rear Wall - Ar64.10-P-5746-03LWE
  • Remove/Install Rear Wall - Ar64.10-P-5746LWE
  • Cut Off Rear End Center Assembly - Ar64.20-P-1000-02LWE
  • Cut Off Rear End Center Assembly - Ar64.20-P-1000-02LWT
  • Prepare Bottom Rear Center Section For Installation - Ar64.20-P-1000-07LWE
  • Prepare Bottom Rear Center Section For Installation - Ar64.20-P-1000-07LWT
  • Install And Weld In Bottom Rear Center Section - Ar64.20-P-1000-08LWE
  • Install And Weld In Bottom Rear Center Section - Ar64.20-P-1000-08LWT
  • Replace Complete Bottom Rear Center Section - Ar64.20-P-1000LWE
  • Replace Complete Bottom Rear Center Section - Ar64.20-P-1000LWT
  • Install Cross Member And Weld In - Ar64.20-P-1060-03LWE
  • Install Cross Member And Weld In - Ar64.20-P-1060-03LWT
  • Remove CROSSMEMBER - Ar64.20-P-1060-10LWE
  • Remove CROSSMEMBER - Ar64.20-P-1060-10LWT
  • Prepare CROSSMEMBER For Installation - Ar64.20-P-1060-11LWE
  • Prepare CROSSMEMBER For Installation - Ar64.20-P-1060-11LWT
  • Replace Bottom Rear Center Section Together With Rear CROSSMEMBER - Ar64.20-P-1060LWE
  • Replace Bottom Rear Center Section Together With Rear CROSSMEMBER - Ar64.20-P-1060LWT
  • Remove Rear Shock-Absorber Strut Tower - Ar64.20-P-1160-01LWE
  • Remove Rear Shock-Absorber Strut Tower - Ar64.20-P-1160-01LWT
  • Prepare Rear Shock-Absorber Strut Tower - Ar64.20-P-1160-02LWE
  • Prepare Rear Shock-Absorber Strut Tower - Ar64.20-P-1160-02LWT
  • Install Rear Shock-Absorber Strut Tower - Ar64.20-P-1160-03LWE
  • Install Rear Shock-Absorber Strut Tower - Ar64.20-P-1160-03LWT
  • Replace Rear Shock-Absorber Strut Tower - Ar64.20-P-1160LWE
  • Replace Rear Shock-Absorber Strut Tower - Ar64.20-P-1160LWT
  • Repair Side Rear End Damage - Ar64.20-P-1251LWE
  • Repair Side Rear End Damage - Ar64.20-P-1251LWT
  • Partially Remove Rear Longitudinal Member - Ar64.20-P-1260-01LWE
  • Prepare Rear Longitudinal Member Section - Ar64.20-P-1260-02LWE
  • Install Rear Longitudinal Member Section - Ar64.20-P-1260-03LWE
  • Remove Rear Floor - Ar64.20-P-1300-01LWE
  • Prepare Rear Floor Assembly - Ar64.20-P-1300-02LWE
  • Install Rear Floor - Ar64.20-P-1300-04LWE
  • Removing Cross Member Above Rear Axle - Ar64.20-P-1300-07LWE
  • Preparing Cross Member Above Rear Axle For Installation - Ar64.20-P-1300-08LWE
  • Completely Replace Rear Floor - Ar64.20-P-1300LWE
  • Install CROSSMEMBER Above Rear Axle - Ar64.20-P-1301-01LWE
  • Replace CROSSMEMBER Above Rear Axle - Ar64.20-P-1301LWE
• Torque Specifications
  • Tightening Torques: Passenger Cars: Rear Wall And Rear End - BA64.00-Z-9999AZ
• Special Tools
  • 201 589 00 27 00 Cross-Brace - WS64.00-P-0012K