Alarm & Parking Assistance - Installation Instructions, Accessories

• Accessory Electronic Module (AEM) (1999-2006)
  • Accessory Electronic Module (AEM)
    • Installation
      • Preparations
      • Removing clips
      • Removing panel and wiring
      • Installing wiring harness
      • Removing rear electronic module (REM)
      • Removing connectors
      • Installing cable and reinstalling connectors
      • Removing connector
      • Installing cables and reinstalling connectors
      • Installing fuse
      • Installing new bracket
      • Installing foam tape and cable
      • Inserting control module
      • Finishing
• Accessory Electronic Module Tailored Reversing Warning System (1999-2003)
  • Accessory electronic module tailored reversing warning system
    • Notes
    • Preparations
    • Removing rear bumper
    • Installing sensors
      • Installing backing paper
      • Removing clips, inner lock facings and catches
      • Drilling and preparing holes
      • Preparing for sensor installation
      • Installing sensors
      • Installing cable harness
      • Finishing
    • Installing rear bumper
      • Routing cable harness
      • Installing bumper
      • Riveting bumper cover liner
    • Installing cable harness and control module
      • Installing control module and sensor cable
      • Removing AEM module and connector
      • Installing cable harness
      • Reinstallation
    • Finishing work
• Accessory Electronic Module With Wiring Kit (1999-2002)
  • Accessory electronic module with wiring kit
    • Preparations
    • Removal
    • Routing and connecting cables
    • Installing control module
    • Installing fuse
    • Reinstallation
    • Finishing
• Adapter Cable, Reversing Warning System (1999-2002)
  • Adapter cable, reversing warning system
    • Removing connector
    • Installing connectors
• Alarm, Basic Kit (1999-2006)
  • Alarm, basic kit
    • Notes
    • Preparation
    • Removing bumper
    • Folding fender liner
    • Installing alarm
    • Removing headlamp
    • Removing cover and cable
    • Removing hood catch
    • Installing new hood catch
    • Reinstallation
    • Installing fuse and programming software
    • Installing decals
• Movement Sensor (1999-2006)
  • Movement sensor
    • Notes
    • Removing cover
    • Installing movement sensor
    • Program software
• Parking Assistance Module (PAM), Rear (2005-2006)
  • Parking assistance module (PAM), rear
    • Preparations
      • Notes
      • Removal
      • Installing backing paper
      • Removing outer lock facings and lower catches
    • Installing sensors
      • Preparing holes
      • Preparing sensors
      • Installing sensor holders
      • Installing cable harness
      • Routing cable
      • Painting holders and sensors
      • Reinstalling bumper
      • Riveting liner
    • Installing parking assistance module (PAM)
      • Installing parking assistance module
      • Connecting cable harness to PAM
      • Applying activator
      • Securing control module
    • Installing switch
      • Removing panels
      • Detaching surround
      • Installing new switch
    • Finishing work
• Parking Assistance, Front (2005-2006)
  • Parking assistance, front
    • Notes
    • Preparations
    • Removal and exterior preparations
    • Preparing bumper
    • Preparing passenger compartment
    • Folding aside mat
    • Preparing seats
    • Removing center panel covers
    • Lifting out mat and removing panels
    • Installing cable harness from bumper
    • Routing cable
    • Cable routing to passenger compartment
    • Preparing and installing cable connector
    • Connecting cable
    • Marking holes for sensors
    • Drilling holes for sensors
    • Marking and drilling holes
    • Creating cut-outs
    • Preparing bumper for sensors and holders
    • Installing sensor holders
    • Installing sensors and cable harness
    • Reassembling bumper
    • Painting sensors and holders
    • Connecting connectors and re-installing bumper
    • Finishing work
    • Programming system
• Reverse Warning System (1999-2004)
  • Reverse warning system
    • Notes
    • Preparations
    • Removal and exterior preparations
    • Preparing bumper
    • Disassembling bumper
    • Marking and drilling holes
    • Cleaning and taping mating surfaces on inside of bumper
    • Preparing sensor holders
    • Installing holders
    • Installing sensors
    • Assembling bumper
    • Drilling body
    • Routing wiring
    • Reinstallation
    • Installing control module on right-hand body side
    • Installing and connecting buzzer
    • Installing switch to shut off reverse warning system (used when reversing with a trailer for example)
    • Connecting switch
• Switch For The Sensor Shut Off Function (1999-2006)
  • Switch for sensor shut off function
    • Notes
    • Preparations
      • Notes
      • Removing panels
      • Removing dashboard environment panel
      • Removal
    • Installation
    • Finishing work
• Tilt Sensor (1999-2006)
  • Tilt sensor
    • Notes
    • Installing
      • Preparations
      • Installation
    • Software programming
• ALCOLOCK, Installation Kit (1999-2006)
  • Alcolock, installation kit
    • Installation of installation kit
      • Preparations
      • Removing soundproofing panel
      • Removing lower cover for steering column
      • Removing passenger side soundproofing panel
      • Inserting and routing cable harness
      • Installing cable harness
      • Pulling cable harness
      • Removing cable duct and disconnecting connector for ignition switch
      • Connecting cables
      • Securing cable harness
      • Reinstalling sound proofing
      • Finishing
    • Position description of connectors for alcolock