Section 776 (87 - Air Conditioning)

WARNING: This page is about a different car, the 2016 Porsche Macan and 2015 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.

WM 870101 Checking air-conditioning system
- Tools
- Troubleshooting the air-conditioning system following complaints about cooling output
- Troubleshooting the air conditioning system following complaints about noises
WM 870101 Function test on air conditioning
- Function test on air conditioning
  - General information
  - Procedure and general requirements for testing
- Technical values
  - Centre vent temperature as a function of outside temperature
  - High pressure in refrigerant circuit as a function of outside temperature
WM 870129 Cleaning refrigerant circuit
- Tools
  - Air conditioning servicing equipment
  - Adapters for cleaning the refrigerant circuit
- Preliminary work
  - Preliminary work for cleaning refrigerant circuit
- Cleaning refrigerant circuit
- Subsequent work
  - Subsequent work for cleaning refrigerant circuit
WM 870225 Symptom in Vehicle Interior - Air-conditioning System Does Not Function: Re-programming air-conditioning control unit (SY 27/15)
- Tools
- General information
- Re-programming air-conditioning control unit
WM 870225 Symptom in Vehicle Interior - Complaint Regarding Memory Function of Rear Air-conditioning Control Unit and Noise Caused by Flaps on all Versions: Re-programming air-conditioning control unit (SY 122/17)
- Tools
WM 870317 Draining and filling refrigerant R134a
- General warning notes
  - Warning notes for handling refrigerant
- Technical values
  - Air conditioning servicing equipment
- Draining and filling refrigerant
  - Assembly work involving the refrigerant system
  - General installation sequence
WM 871419 Removing and installing sun sensor
- Preliminary work
- Removing and installing sun sensor
  - Removing sun sensor
  - Installing sun sensor
- Subsequent work
WM 872019 Removing and installing servo motor for fresh air/recirculated air
- Tools
- Preliminary work
- Removing and installing servo motor for fresh air
- Subsequent work
WM 872019 Removing and installing servo motor for ram air
- Tools
- Preliminary work
- Removing and installing servo motor for recirculated air
- Subsequent work
WM 872019 Removing and installing servo motor for defroster
- Tools
- Preliminary work
- Removing and installing servo motor for defroster
- Subsequent work
WM 872019 Removing and installing servo motor for front left temperature valve
- Tools
- Preliminary work
- Removing and installing servo motor for front left temperature valve
- Subsequent work
WM 872019 Removing and installing servo motor for rear left temperature valve (3-zone air conditioning)
- Tools
- Preliminary work
- Removing and installing servo motor for rear left temperature valve
- Subsequent work
WM 872019 Removing and installing servo motor for front left footwell
- Tools
- Preliminary work
- Removing and installing servo motor for front left footwell
  - Removing servo motor for front left footwell
  - Installing servo motor for front left footwell
- Teaching servo motor
- Subsequent work
WM 872019 Removing and installing servo motor for right center vent
- Tools
- Preliminary work
- Removing and installing servo motor for right center vent
- Subsequent work
WM 872019 Removing and installing servo motor for front right footwell
- Tools
- Preliminary work
- Removing and installing servo motor for front right footwell
- Subsequent work
WM 872019 Removing and installing servo motor for front right temperature valves
- Tools
- Preliminary work
- Removing and installing servo motor for front right temperature valves
- Subsequent work
WM 872019 Removing and installing servo motor for left center vent
- Tools
- Preliminary work
- Removing and installing servo motor for left center vent
  - Removing servo motor for left center vent
  - Installing servo motor for left center vent
- Teaching servo motor
- Subsequent work
WM 872025 Symptom-based repair instructions for body interior: Re-calibrating servo motors for air conditioning (Different ventilation temperatures/SY2015)
- Tools
- General information
  - Symptom
  - Cause and remedial action
    - Cause
    - Remedial action
- Tools and materials
- Re-calibrating servo motors for air conditioning
- Invoicing
WM 8720IN Installation position of servo motors on heating/fresh-air unit
- Information
  - Component information
WM 872219 Removing and installing air quality sensor
- Information
  - Installation position of air quality sensor
- Preliminary work
  - Preliminary work for air quality sensor
- Removing air quality sensor
- Installing air quality sensor
- Subsequent work
  - Subsequent work for air quality sensor
WM 873419 Removing and installing air-conditioning compressor
- Tools
- Technical values
- Preliminary work
- Removing and installing air-conditioning compressor
- Subsequent work
- Compressor run-in after installing a new air-conditioning compressor
WM 874319 Removing and installing compressor/condenser line
- Technical values
- Installation position
- Preliminary work
- Removing and installing compressor/condenser line
- Subsequent work
WM 874419 Removing and installing condenser-evaporator line
- Tools
- Technical values
- Installation position
- Preliminary work
  - Preliminary work (section from condenser to wheel housing)
  - Preliminary work (section from wheel housing to engine compartment)
- Removing and installing condenser-evaporator line
- Subsequent work
  - Subsequent work (section from condenser to wheel housing)
  - Subsequent work (section from wheel housing to engine compartment)
WM 874519 Removing and installing compressor/evaporator line
- Tools
- Technical values
- Installation position
- Preliminary work
  - Preliminary work (section from engine compartment to expansion valve)
- Removing and installing compressor/evaporator line
- Subsequent work
  - Subsequent work (section from engine compartment to expansion valve)
WM 875019 Removing and installing condenser
- Technical values
- Preliminary work
- Removing and installing condenser
  - Removing condenser
  - Installing condenser
- Subsequent work
WM 875819 Removing and installing temperature sensor
- Preliminary work
- Removing and installing temperature sensor
- Subsequent work
WM 877019 Removing and installing expansion valve
- Technical values
- Preliminary work
- Removing and installing expansion valve
  - Removing expansion valve
  - Installing expansion valve
- Subsequent work
WM 877819 Removing and installing fan control
- Preliminary work
- Removing and installing fan control
  - Removing fan control
  - Installing fan control
- Subsequent work
WM 878319 Removing and installing pressure switch
- Preliminary work
  - Preliminary work for pressure switch
- Removing and installing pressure switch
  - Removing pressure switch
  - Installing pressure switch
- Subsequent work
  - Subsequent work for pressure switch