Rear Axle -- Testing & Repair -- E350 (211.256) - 3 Of 3

• Testing & Repair
  • Pulling tapered roller bearing inner races off differential - AR35.31-P-0550-04T
  • Loosening and unscrewing hexagon collar nut on joint flange - AR35.31-P-0550-05T
  • Pulling off joint flange - AR35.31-P-0550-06T
  • Pressing drive pinion out of rear axle housing - AR35.31-P-0550-07T
  • Pressing radial seal out of rear axle housing - AR35.31-P-0550-08T
  • Removing tapered roller bearing outer races from rear axle housing - AR35.31-P-0550-09T
  • Pulling tapered roller bearing inner race off drive pinion - AR35.31-P-0550-10T
  • Pressing tapered roller bearing inner race onto drive pinion - AR35.31-P-0550-12T
  • Calculating shim and inserting into rear axle housing - AR35.31-P-0550-13T
  • Pull tapered roller bearing outer races into rear axle housing - AR35.31-P-0550-14T
  • Installing drive pinion in rear axle housing - AR35.31-P-0550-15T
  • Installing tapered roller bearing inner race on drive pinion and pressing in together with radial sealing ring - AR35.31-P-0550-16T
  • Adjusting friction torque of drive pinion bearing - AR35.31-P-0550-17T
  • Checking adjustment dimension of drive pinion - AR35.31-P-0550-18T
  • Mounting crown wheel on differential - AR35.31-P-0550-19T
  • Pressing tapered roller bearing inner races onto differential - AR35.31-P-0550-20T
  • Inserting right tapered roller bearing outer race in rear axle housing - AR35.31-P-0550-21T
  • Inserting right locking ring - AR35.31-P-0550-22T
  • Pretension rear axle housing with spreader (brace) - AR35.31-P-0550-23T
  • Measure expanded dimension of rear axle housing - AR35.31-P-0550-24T
  • Measuring gear backlash between crown wheel and pinion and correcting if necessary - AR35.31-P-0550-25T
  • Installing spacer sleeve with bearing washers on both sides on drive pinion - AR35.31-P-0550-26T
  • Inserting left locking ring - AR35.31-P-0550-27T
  • Attaching end cover - AR35.31-P-0550-28T
  • Securing hexagon collar nut on drive pinion joint flange - AR35.31-P-0550-29T
  • Disassembling and assembling rear axle differential, adjusting gear set - AR35.31-P-0550T
  • Remove/install end cover at differential - AR35.31-P-0554T
  • Clamping differential housing - AR35.31-P-0560-01T
  • Driving out and driving in differential pin and roll pin - AR35.31-P-0560-02T
  • Removing differential bevel gears and differential side gears - AR35.31-P-0560-03T
  • Installing differential side gears and differential bevel gears - AR35.31-P-0560-04T
  • Check friction torque of differential - AR35.31-P-0560-05T
  • Disassembling and assembling differential - AR35.31-P-0560T
  • Tightening torques: Passenger cars: Rear axle - BA35.00-Z-9999AZ
  • Rear axle carrier - BA35.10-P-1000-01E
  • Spring control arm - BA35.20-P-1000-01A
  • Camber strut - BA35.20-P-1000-02C
  • Torque strut - BA35.20-P-1000-03C
  • Tie rod - BA35.20-P-1000-04C
  • Thrust arm - BA35.20-P-1000-05C
  • Hub - BA35.20-P-1000-06A
  • Rear axle shaft - BA35.30-P-1000-01F
  • Rear axle differential ring and pinion - BA35.31-P-1000-01A
  • Rear axle differential housing - BA35.31-P-1000-02A