Diagnostic Trouble Code (DTC) Chart
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| PCM | P0657:00 | Actuator Supply Voltage "A" Circuit Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0702:00 | Transmission Control System Electrical: No Sub Type Information | GO to Pinpoint Test I |
| PCM | P0706:00 | Transmission Range Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P0707:00 | Transmission Range Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P0708:00 | Transmission Range Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P0709:00 | Transmission Range Sensor "A" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P0710:00 | Transmission Fluid Temperature Sensor "A" Circuit: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0711:00 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0712:00 | Transmission Fluid Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0713:00 | Transmission Fluid Temperature Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0715:00 | Turbine Shaft Speed (TSS) Sensor Circuit: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0716:00 | Turbine Shaft Speed (TSS) Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0716:00 | Turbine Shaft Speed (TSS) Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test G |
| PCM | P0717:00 | Turbine Shaft Speed (TSS) Sensor Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0718:00 | Turbine Shaft Speed (TSS) Sensor Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0720:00 | Output Shaft Speed (OSS) Sensor Circuit: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0721:00 | Output Shaft Speed (OSS) Sensor Circuit Range Performance: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0721:00 | Output Shaft Speed (OSS) Sensor Circuit Range Performance: No Sub Type Information | GO to Pinpoint Test G |
| PCM | P0722:00 | Output Shaft Speed (OSS) Sensor Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0729:00 | Gear 6 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test J |
| PCM | P0731:00 | Gear 1 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test K |
| PCM | P0732:00 | Gear 2 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test L |
| PCM | P0733:00 | Gear 3 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test M |
| PCM | P0734:00 | Gear 4 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test N |
| PCM | P0735:00 | Gear 5 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test O |
| PCM | P0736:00 | Reverse Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test P |
| PCM | P073D:00 | Unable to Engage Neutral: No Sub Type Information | GO to Pinpoint Test Q |
| PCM | P073E:00 | Unable to Engage Reverse: No Sub Type Information | GO to Pinpoint Test R |
| PCM | P073F:00 | Unable to Engage Gear 1: No Sub Type Information | GO to Pinpoint Test S |
| PCM | P0740:00 | Torque Converter Clutch Solenoid Circuit Open: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0741:00 | Torque Converter Clutch Solenoid Circuit Performance Stuck Off: No Sub Type Information | GO to Pinpoint Test T |
| PCM | P0743:00 | Torque Converter Clutch Solenoid Circuit Electrical: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0748:00 | Pressure control solenoid Electrical "A": No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0751:00 | Shift Solenoid "A" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test U |
| PCM | P0752:00 | Shift Solenoid "A" Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P0753:00 | Shift Solenoid "A" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0754:00 | Shift Solenoid "A" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0756:00 | Shift Solenoid "B" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test U |
| PCM | P0757:00 | Shift Solenoid "B" Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P0758:00 | Shift Solenoid "B" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0759:00 | Shift Solenoid "B" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0761:00 | Shift Solenoid "C" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test U |
| PCM | P0762:00 | Shift Solenoid "C" Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P0763:00 | Shift Solenoid "C" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0764:00 | Shift Solenoid "C" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0766:00 | Shift Solenoid "D" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test U |
| PCM | P0767:00 | Shift Solenoid "D" Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P0768:00 | Shift Solenoid "D" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0769:00 | Shift Solenoid "D" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P076F:00 | Gear 7 Ratio Incorrect: No Sub Type Information | GO to Pinpoint Test W |
| PCM | P0771:00 | Shift Solenoid "E" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test U |
| PCM | P0772:00 | Shift Solenoid "E" Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P0773:00 | Shift Solenoid "E" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0774:00 | Shift Solenoid "E" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P077D:00 | Output Shaft Speed (OSS) Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0791:00 | Intermediate Shaft Speed Sensor "A" Circuit: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0792:00 | Intermediate Shaft Speed Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test G |
| PCM | P0793:00 | Intermediate Shaft Speed Sensor "A" Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0793:00 | Output Shaft Speed (OSS) Sensor "A" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P0794:00 | Intermediate Shaft Speed Sensor "A" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P07C0:00 | Turbine Shaft Speed (TSS) Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P07C6:00 | Intermediate Shaft Speed Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| PCM | P07D9:00 | Gear 8 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test X |
| PCM | P0840:00 | Transmission Fluid Pressure Sensor/Switch "A" Circuit: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0841:00 | Transmission Fluid Pressure Sensor/Switch "A" Circuit/Range Performance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0842:00 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0843:00 | Transmission Fluid Pressure Sensor/Switch "A" Circuit High: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0845:00 | Transmission Fluid Pressure Sensor/Switch "B" Circuit: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0846:00 | Transmission Fluid Pressure Sensor/Switch "B" Circuit/Range Performance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0847:00 | Transmission Fluid Pressure Sensor/Switch "B" Circuit Low: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0848:00 | Transmission Fluid Pressure Sensor/Switch "B" Circuit High: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0868:00 | Transmission Fluid Pressure Low: No Sub Type Information | GO to Pinpoint Test Y |
| PCM | P0869:00 | Transmission Fluid Pressure High: No Sub Type Information | GO to Pinpoint Test Y |
| PCM | P0882:00 | TCM Power Input Signal Low: No Sub Type Information | GO to Pinpoint Test I |
| PCM | P0883:00 | TCM Power Input Signal High: No Sub Type Information | GO to Pinpoint Test I |
| PCM | P093A:00 | Hydraulic Accumulator Solenoid Circuit Open: No sub Type Information | GO to Pinpoint Test E |
| PCM | P093B:00 | Hydraulic Accumulator Solenoid Circuit Low: No sub Type Information | GO to Pinpoint Test E |
| PCM | P093C:00 | Hydraulic Accumulator Solenoid Circuit High: No sub Type Information | GO to Pinpoint Test E |
| PCM | P093D:00 | Hydraulic Accumulator Solenoid Circuit Performance: No sub Type Information | GO to Pinpoint Test E |
| PCM | P0960:00 | Pressure Control Solenoid Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0961:00 | Pressure Control Solenoid "A" Control Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0962:00 | Pressure Control Solenoid "A" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0963:00 | Pressure Control Solenoid "A" Control Circuit High: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P0973:00 | Shift Solenoid "A" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0974:00 | Shift Solenoid "A" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0976:00 | Shift Solenoid "B" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0977:00 | Shift Solenoid "B" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0979:00 | Shift Solenoid "C" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P097A:00 | Shift Solenoid "A" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P097B:00 | Shift Solenoid "B" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P097C:00 | Shift Solenoid "C" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P097E:00 | Shift Solenoid "E" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P097F:00 | Shift Solenoid "F" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0980:00 | Shift Solenoid "C" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0982:00 | Shift Solenoid "D" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0983:00 | Shift Solenoid "D" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0985:00 | Shift Solenoid "E" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0986:00 | Shift Solenoid "E" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0998:00 | Shift Solenoid "F" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P0999:00 | Shift Solenoid "F" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P1001:00 | KOER Not Able to Complete, KOER Aborted: No Sub Type Information | GO to Pinpoint Test Z |
| PCM | P1397:00 | System Voltage Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test I |
| PCM | P1636:00 | Inductive Signature Chip Communication Error: No Sub Type Information | GO to Pinpoint Test AA |
| PCM | P163E:00 | Transmission Control Module Programming Error: No Sub Type Information | GO to Pinpoint Test AB |
| PCM | P163F:00 | Transmission ID Block Corrupted, Not Programmed: No Sub Type Information | GO to Pinpoint Test AB |
| PCM | P1711:00 | Transmission Fluid Temperature Sensor Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P1744:00 | Torque Converter Clutch Solenoid Circuit Performance: No Sub Type Information | GO to Pinpoint Test AC |
| PCM | P1783:00 | Transmission Fluid Over Temperature Condition: No Sub Type Information | GO to Pinpoint Test AD |
| PCM | P1A02:00 | Transmission One Way Clutch Performance: No Sub Type Information | GO to Pinpoint Test AE |
| PCM | P2669:00 | Actuator Supply Voltage "B" Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P2669:00 | Actuator Supply Voltage "B" Circuit Open: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P26C3:00 | Internal Control Module Transmission Range Sensor Performance: No Sub Type Information | GO to Pinpoint Test AF |
| PCM | P2700:00 | Transmission Friction Element "A" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AG |
| PCM | P2701:00 | Transmission Friction Element "B" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AG |
| PCM | P2702:00 | Transmission Friction Element "C" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AG |
| PCM | P2703:00 | Transmission Friction Element "D" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AG |
| PCM | P2704:00 | Transmission Friction Element "E" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AG |
| PCM | P2705:00 | Transmission Friction Element "F" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AG |
| PCM | P2707:00 | Shift Solenoid "F" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test U |
| PCM | P2708:00 | Shift Solenoid "F" Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P2709:00 | Shift Solenoid "F" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P2710:00 | Shift Solenoid "F" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| PCM | P2758:00 | Torque Converter Clutch Pressure Control Solenoid Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| PCM | P2760:00 | Torque Converter Clutch Pressure Control Solenoid Intermittent: No Sub Type Information | GO to Pinpoint Test F |
| PCM | P2783:00 | Torque Converter Temperature Too High: No Sub Type Information | GO to Pinpoint Test AH |
| PCM | P27B2:00 | Internal Control Module Transmission Range Control Performance: No Sub Type Information | GO to Pinpoint Test AI |
| PCM | P27B3:00 | Internal Control Module Transmission Gear Select Performance: No Sub Type Information | GO to Pinpoint Test AI |
| PCM | P27B4:00 | Internal Control Module Transmission Gear Direction Control Performance: No Sub Type Information | GO to Pinpoint Test AI |
| PCM | P27B5:00 | Internal Control Module Transmission Gear Ratio Control Performance: No Sub Type Information | GO to Pinpoint Test AI |
| PCM | P27B6:00 | Internal Control Module Transmission Speed Sensor Performance: No Sub Type Information | GO to Pinpoint Test AI |
| PCM | P2801:00 | Transmission Range Sensor "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P2802:00 | Transmission Range Sensor "B" Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P2803:00 | Transmission Range Sensor "B" Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P2804:00 | Transmission Range Sensor "B" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test C |
| PCM | P2805:00 | Transmission Range Sensor "A"/"B" Correlation: No Sub Type Information | GO to Pinpoint Test C |