Section 41 (37 - Automatic Transmission - Actuator, Housing (4.8L Non Turbo) -- 92A - Cayenne (92A))

• SY, 3700AN Eliminating Transmission Symptoms - Teaching Reverse Gear Transmission Adaptation On TIPTRONIC Transmission (I-No. G1G) (Jerking And Knocking Noise When Engaging Reverse Gear/SY3310)
  • General Information
    • Symptom
    • Cause, Date Of Introduction And Remedial Action
      • Cause
      • Date Of Introduction
      • Remedial Action
• WM, 370235 Checking And Topping Up ATF
  • Tools
  • Technical Values
  • Information
    • Test Conditions With Cooler Lines Closed
    • Test Conditions After Opening Cooler Lines
  • Preliminary Work For ATF
  • Checking ATF
  • Topping Up ATF
  • Subsequent Work For ATF
• WM, 370255 Changing ATF
  • Tools
  • Technical Values
  • Preliminary Work For ATF
  • Changing ATF
  • Subsequent Work For ATF
• WM, 370419 Removing And Installing Selector Knob
  • Tools
  • Removing Selector Knob
  • Installing Selector Knob
    • Releasing Selector Knob
• WM, 370819 Removing And Installing Selector Support
  • Technical Values
  • Preliminary Work
  • Removing Selector Support
  • Installing Selector Support
    • Installing Support
  • Subsequent Work
• WM, 371515 Adjusting Selector Lever Cable
  • Technical Values
  • Preliminary Work
  • Adjusting Selector Lever Cable
  • Subsequent Work
• WM, 371519 Removing And Installing Selector Lever Cable
  • Tools
  • Preliminary Work
  • Removing Selector Lever Cable
  • Installing Selector Lever Cable
  • Subsequent Work
• SY, 3730 Eliminating Transmission Symptoms - Re-Programming Control Unit For TIPTRONIC Transmission (I-No. G1G) (Hard Gear Changes - Even During "KICKDOWN" Downshifts/SY16/13)
  • Tools
  • General Information
    • Notes
    • Symptom
    • Cause, Date Of Introduction And Remedial Action
      • Cause
      • Date Of Introduction
      • Remedial Act Ion
  • Tools And Materials
  • Re-Programming Control Unit For TIPTRONIC Transmission
    • Preliminary Work
    • Re-Programming Dme Control Unit
      • Notes
      • Carrying Out Control Unit Coding
      • Performing Throttle Valve Adaptation
    • Reading Out And Erasing Fault Memory
    • Subsequent Work
  • Invoicing
• Ti, 3730 Control Unit For TIPTRONIC Transmission (I-No. G1G) Needs To Be Replaced: Re-Programming (56/13)
  • Tools
• WM, 373019 Removing And Installing Transmission Control Unit
  • Tools
  • Preliminary Work
  • Removing Transmission Control Unit
  • Installing Transmission Control Unit
  • Subsequent Work
• WM, 373115 Adjusting Multi-Functional Switch
  • Tools
  • Technical Values
  • Preliminary Work
    • Preliminary Work For Multi-Functional Switch
  • Adjusting Multi-Functional Switch
  • Subsequent Work For Multi-Functional Switch
• WM, 373119 Removing And Installing Multi-Functional Switch
  • Technical Values
  • Preliminary Work
    • Preliminary Work For Multi-Functional Switch
  • Removing Multi-Functional Switch
  • Installing Multi-Functional Switch
  • Subsequent Work
    • Subsequent Work For Multi-Functional Switch
• WM, 373519 Removing And Installing Automatic Transmission
  • Tool
  • Technical Values
  • Preliminary Work
  • Removing Automatic Transmission
  • Installing Automatic Transmission
  • Subsequent Work
• WM, 373527 Removing And Mounting Automatic Transmission
  • Tools
  • Technical Values
  • Preliminary Work
  • Removing Automatic Transmission
  • Mounting Automatic Transmission
  • Subsequent Work
    • Subsequent Work For Removing And Mounting Transmission
• WM, 374055 Replacing Transmission Mount
  • Tools
  • Preliminary Work
  • Removing Transmission Mount
  • Installing Transmission Mount
  • Subsequent Work
• WM, 375519 Removing And Installing ATF Pan
  • Technical Values
  • Preliminary Work
  • Removal
    • Removing ATF Pan
  • Installation
    • Installing ATF Pan
  • Subsequent Work
• WM, 375819 Removing And Installing ATF Filter
  • Technical Values
  • Preliminary Work
  • Removal
    • Removing ATF Filter
  • Installation
    • Installing ATF Filter
  • Subsequent Work