Section 398 (Automatic Transmission - 6L80/6L90 - Repair Instructions - Off Vehicle)
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
- Repair Instructions - Off Vehicle
- Torque Converter Removal and Holding Fixture Installation
- Case Extension Assembly Removal
- Transmission Fluid Pan, Filter and Electrical Connector Passage Sleeve Removal (6L80)
- Control Valve Body Assembly Removal
- Torque Converter Housing with Fluid Pump Removal
- 1-2-3-4 and 3-5 Reverse Clutch Assembly and 4-5-6 Clutch Assembly Removal (6L50/80/90)
- Center Support, Output Carrier and Output Shaft Removal (6L80/6L90)
- Manual Shift Shaft and Parking System Components Overhaul (6L80/6L90)
- Manual Shift Shaft Seal Replacement
- Output Shaft Seal Replacement (AWD Models Only)
- Case Inspection
- Output Shaft Disassemble (6L80)
- Output Shaft Assemble (6L50/80/90)
- Output Carrier Assembly Overhaul (6L80)
- Output Carrier Assembly Overhaul (6L90)
- Output Carrier to Output Shaft Assemble (6L80/6L90)
- 2-6 Clutch Overhaul (6L80)
- 2-6 Clutch Overhaul (6L90)
- Low and Reverse Clutch Overhaul (6L80)
- Low and Reverse Clutch Overhaul (6L90)
- Low and Reverse Clutch Backing Plate Retaining Ring Measurement
- 4-5-6 Clutch Dampener Overhaul (6L50/80/90)
- 4-5-6 Clutch Overhaul (6L80/6L90)
- 4-5-6 Clutch Backing Plate Retaining Ring Measurement
- 1-2-3-4 and 3-5 Reverse Clutch Overhaul (6L50/6L80/6L90)
- 1-2-3-4 and 3-5 Reverse Clutch Plates Removal
- 1-2-3-4 Clutch Piston Removal
- 3-5 Reverse Clutch Piston Removal
- 3-5 Reverse Clutch Air Bleed Inspection (6L80/6L90)
- 3-5 Reverse Clutch Housing Inspection Disassembled
- 3-5 Reverse Clutch Housing Inspection Assembled
- 1-2-3-4 and 3-5 Reverse Clutch Piston Seals Replacement
- 3-5 Reverse Clutch Piston Installation
- 1-2-3-4 Clutch Piston Installation
- 1-2-3-4 Clutch Plate Installation
- 3-5 and Reverse Clutch Plate Installation
- 1-2-3-4 and 3-5 Reverse Clutch Bearing Assembly Replacement
- 1-2-3-4 Clutch Backing Plate Retaining Ring Measurement
- 3-5 Reverse Clutch Backing Plate Retaining Ring Measurement (6L80/6L90)
- Torque Converter Housing with Fluid Pump Disassemble
- Fluid Pump Cover Cleaning and Inspection
- 1-2-3-4 and 3-5 Reverse Clutch Fluid Seal Ring Installation (6L80/6L90)
- Torque Converter Housing Cleaning and Inspection
- Torque Converter Fluid Seal Replacement
- Transmission Fluid Cooler Pipe Seal Replacement
- Fluid Pump Selective Measurement
- Torque Converter Housing with Fluid Pump Assemble
- Fluid Pump Cover Installation
- Control Valve Body Assembly Disassemble
- Control Valve Lower Body Assembly Cleaning and Inspection
- Control Valve Upper Body Assembly Cleaning and Inspection
- Control Valve Body Assembly Assemble
- Upper to Lower Control Valve Body Assembly Assemble
- Filter Plate Installation
- Control Solenoid Valve Assembly Installation
- Manual Shift Shaft Position Switch Installation
- Valve Body, Control Solenoid Torque Sequence
- Control Solenoid Valve Assembly Contact Gap Inspection
- Input and Output Speed Sensor Assembly Installation
- Center Support, Output Carrier and Output Shaft Installation (6L80/6L90)
- 1-2-3-4 and 3-5 Reverse Clutch Assembly and 4-5-6 Clutch Assembly Installation (6L80/6L90)
- Torque Converter Housing with Fluid Pump Installation
- Propeller Shaft Front Slip Yoke Oil Seal Replacement
- Control Valve Body Assembly Installation
- Automatic Transmission Electrical Connector Passage Sleeve Installation
- Fluid Filter and Manual Shift Detent Assembly Installation
- Transmission Fluid Pan Installation (6L80)
- Case Extension Assembly Installation
- Torque Converter Installation and Holding Fixture Removal