Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2022 Ford Police Interceptor Utility and 2022 Ford Explorer. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| APIM | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| BCM | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| BCMC | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| BECM | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| DCDC | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| IPC | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| PAM | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test BT |
| SOBDMC | C0030:00 | Left Front Tone Wheel: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0033:00 | Right Front Tone Wheel: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0036:00 | Left Rear Tone Wheel: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0039:00 | Right Rear Tone Wheel: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0049:00 | Brake Fluid Level: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C004B:00 | Brake Fluid Level Sensor/Switch "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C004C:00 | Brake Booster Motor "A" Position Sensor Exceeded Learning Limit: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C004E:00 | Brake System Pressure Control Valve Actuator Stuck: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C004F:00 | ABS Control Module Over Temperature: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0061:00 | Lateral Acceleration Sensor: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0062:00 | Longitudinal Acceleration Sensor: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0500:00 | Left Front Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0501:00 | Left Front Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0504:00 | Left Front Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0506:00 | Right Front Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0507:00 | Right Front Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C050A:00 | Right Front Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C050C:00 | Left Rear Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C050D:00 | Left Rear Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0510:00 | Left Rear Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0512:00 | Right Rear Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0513:00 | Right Rear Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0516:00 | Right Rear Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0518:00 | Left Front Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0519:00 | Right Front Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C051A:00 | Left Rear Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C051B:00 | Right Rear Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C052B:00 | ABS Pump Motor Control Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C052D:00 | ABS Pump Motor Control Circuit High: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C052E:00 | ABS Pump Motor Control Circuit Low: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C053D:00 | Brake Pressure Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0555:00 | Left Front Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0556:00 | Right Front Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0557:00 | Left Rear Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0558:00 | Right Rear Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C055C:00 | ABS Pump Motor Supply Voltage Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C055E:00 | Brake Hydraulic Circuit "A" Leak: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0560:00 | Brake Pressure Sensor "A" Missing Calibration: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0563:00 | ABS Control Module Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0564:00 | ABS Control Module System Voltage Low: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0565:00 | ABS Control Module System Voltage High: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C056A:00 | Brake Booster Pressure Sensor Power Supply Circuit: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C056B:00 | Brake Pressure Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0594:00 | Brake Booster Motor "A" Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0596:00 | Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C0597:00 | Brake System Control Module "A" Performance: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C1013:00 | Brake System Pressure: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C101F:00 | Generic Valve Failure: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | C113A:62 | Wakeup Control: Signal Compare Failure | GO to Pinpoint Test A |
| SOBDMC | P0560:00 | System Voltage: No Sub Type Information | GO to Pinpoint Test BL |
| SOBDMC | P0562:00 | System Voltage Low: No Sub Type Information | GO to Pinpoint Test BL |
| SOBDMC | P0563:00 | System Voltage High: No Sub Type Information | GO to Pinpoint Test C |
| SOBDMC | P0600:49 | Serial Communication Link: Internal Electronic Failure | GO to Pinpoint Test D |
| SOBDMC | P0600:88 | Serial Communication Link: Bus Off | GO to Pinpoint Test D |
| SOBDMC | P0607:00 | Control Module Performance: No Sub Type Information | GO to Pinpoint Test E |
| SOBDMC | P060A:44 | Internal Control Module Monitoring Processor Performance: Data Memory Failure | GO to Pinpoint Test F |
| SOBDMC | P060A:47 | Internal Control Module Monitoring Processor Performance: Watchdog/Safety μC Failure | GO to Pinpoint Test F |
| SOBDMC | P060A:86 | Internal Control Module Monitoring Processor Performance: Signal Invalid | GO to Pinpoint Test D |
| SOBDMC | P060A:88 | Internal Control Module Monitoring Processor Performance: Bus Off | GO to Pinpoint Test D |
| SOBDMC | P060B:47 | Internal Control Module A/D Processing Performance: Watchdog/Safety μC Failure | GO to Pinpoint Test G |
| SOBDMC | P060B:62 | Internal Control Module A/D Processing Performance: Signal Compare Failure | GO to Pinpoint Test G |
| SOBDMC | P060C:41 | Internal Control Module Main Processor Performance: General Checksum Failure | GO to Pinpoint Test H |
| SOBDMC | P060C:42 | Internal Control Module Main Processor Performance: General Memory Failure | GO to Pinpoint Test H |
| SOBDMC | P060C:44 | Internal Control Module Main Processor Performance: Data Memory Failure | GO to Pinpoint Test H |
| SOBDMC | P060C:47 | Internal Control Module Main Processor Performance: Watchdog/Safety μC Failure | GO to Pinpoint Test H |
| SOBDMC | P0613:86 | TCM Processor: Signal Invalid | GO to Pinpoint Test I |
| SOBDMC | P061A:92 | Internal Control Module Torque Performance: Performance Or Incorrect Operation | GO to Pinpoint Test BM |
| SOBDMC | P061A:93 | Internal Control Module Torque Performance: No Operation | GO to Pinpoint Test BM |
| SOBDMC | P0634:00 | Control Module Internal Temperature "A" Too High: No Sub Type Information | GO to Pinpoint Test J |
| SOBDMC | P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test K |
| SOBDMC | P06A6:00 | Sensor Reference Voltage "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| SOBDMC | P06A7:00 | Sensor Reference Voltage "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| SOBDMC | P06A9:00 | Sensor Reference Voltage "D" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test L |
| SOBDMC | P06B1:00 | Sensor Power Supply "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| SOBDMC | P06B8:00 | Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information | GO to Pinpoint Test M |
| SOBDMC | P0886:00 | TCM Power Relay Control Circuit Low: No Sub Type Information | GO to Pinpoint Test N |
| SOBDMC | P0887:00 | TCM Power Relay Control Circuit High: No Sub Type Information | GO to Pinpoint Test N |
| SOBDMC | P0A0A:13 | High Voltage System Interlock Circuit "A": Circuit Open | GO to Pinpoint Test BN |
| SOBDMC | P0A1A:06 | Generator Control Module: Algorithm Based Failures | GO to Pinpoint Test O |
| SOBDMC | P0A1D:08 | Hybrid/EV Powertrain Control Module "A": Bus Signal/Message Failures | GO to Pinpoint Test P |
| SOBDMC | P0A23:00 | Generator Torque Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test Q |
| SOBDMC | P0A2F:94 | Drive Motor "A" Over Temperature: Unexpected Operation | GO to Pinpoint Test R |
| SOBDMC | P0A37:64 | Generator Temperature Sensor Circuit Range/Performance: Signal Plausibility Failure | GO to Pinpoint Test S |
| SOBDMC | P0A38:00 | Generator Temperature Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test S |
| SOBDMC | P0A39:00 | Generator Temperature Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test S |
| SOBDMC | P0A3C:94 | Drive Motor "A" Inverter Over Temperature: Unexpected Operation | GO to Pinpoint Test T |
| SOBDMC | P0A47:00 | Drive Motor "B" Position Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test U |
| SOBDMC | P0A4C:00 | Generator Position Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test V |
| SOBDMC | P0A4D:00 | Generator Position Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test W |
| SOBDMC | P0A50:92 | Generator Position Sensor Circuit Overspeed: Performance Or Incorrect Operation | GO to Pinpoint Test X |
| SOBDMC | P0A6F:00 | Generator Phase U Current: No Sub Type Information | GO to Pinpoint Test Y |
| SOBDMC | P0A71:00 | Generator Phase U Current High: No Sub Type Information | GO to Pinpoint Test Z |
| SOBDMC | P0A72:00 | Generator Phase V Current: No Sub Type Information | GO to Pinpoint Test Y |
| SOBDMC | P0A74:00 | Generator Phase V Current High: No Sub Type Information | GO to Pinpoint Test Z |
| SOBDMC | P0A75:00 | Generator Phase W Current: No Sub Type Information | GO to Pinpoint Test Y |
| SOBDMC | P0A77:00 | Generator Phase W Current High: No Sub Type Information | GO to Pinpoint Test Z |
| SOBDMC | P0A7A:96 | Generator Inverter Performance: Component Internal Failure | GO to Pinpoint Test AA |
| SOBDMC | P0BCD:00 | Generator Inverter Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test AB |
| SOBDMC | P0BCE:00 | Generator Inverter Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test AC |
| SOBDMC | P0BCF:00 | Generator Inverter Temperature Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test AC |
| SOBDMC | P0C03:00 | Drive Motor "B" Current Low: No Sub Type Information | GO to Pinpoint Test AD |
| SOBDMC | P0C2F:62 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: Signal Compare Failure | GO to Pinpoint Test AE |
| SOBDMC | P0C2F:63 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: Circuit/Component Protection Time-Out | GO to Pinpoint Test AE |
| SOBDMC | P0C5A:00 | Drive Motor "B" Position Sensor Circuit "A": No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C5C:00 | Drive Motor "B" Position Sensor Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C5D:00 | Drive Motor "B" Position Sensor Circuit "A" High: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C5F:00 | Drive Motor "B" Position Sensor Circuit "B": No Sub Type Information | GO to Pinpoint Test AJ |
| SOBDMC | P0C61:00 | Drive Motor "B" Position Sensor Circuit "B" Low: No Sub Type Information | GO to Pinpoint Test AJ |
| SOBDMC | P0C62:00 | Drive Motor "B" Position Sensor Circuit "B" High: No Sub Type Information | GO to Pinpoint Test AJ |
| SOBDMC | P0C64:00 | Generator Position Sensor Circuit A: No Sub Type Information | GO to Pinpoint Test U |
| SOBDMC | P0C65:00 | Generator Position Sensor Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test AF |
| SOBDMC | P0C66:00 | Generator Position Sensor Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C67:00 | Generator Position Sensor Circuit "A" High: No Sub Type Information | GO to Pinpoint Test AG |
| SOBDMC | P0C6A:00 | Generator Position Sensor Circuit "B" Range/Performance: No Sub Type Information | GO to Pinpoint Test AI |
| SOBDMC | P0C6B:00 | Generator Position Sensor Circuit "B" Low: No Sub Type Information | GO to Pinpoint Test AJ |
| SOBDMC | P0C6C:00 | Generator Position Sensor Circuit "B" High: No Sub Type Information | GO to Pinpoint Test AJ |
| SOBDMC | P0C79:00 | Drive Motor "A" Inverter Voltage Too High: No Sub Type Information | GO to Pinpoint Test AK |
| SOBDMC | P0DA8:00 | Hybrid/EV Battery Voltage/Drive Motor "A" Inverter Voltage Correlation: No Sub Type Information | GO to Pinpoint Test AL |
| SOBDMC | P0DFA:00 | Generator Phase U-V-W Current Sensor Correlation: No Sub Type Information | GO to Pinpoint Test AM |
| SOBDMC | P0DFC:00 | Generator Position Sensor Not Learned: No Sub Type Information | GO to Pinpoint Test AN |
| SOBDMC | P0E71:00 | Generator Torque Delivered Performance: No Sub Type Information | GO to Pinpoint Test AO |
| SOBDMC | P1A07:00 | Inverter High Voltage Performance: No Sub Type Information | GO to Pinpoint Test AP |
| SOBDMC | P1A0A:02 | Immediate Shutdown Signal A: General Signal Failure | GO to Pinpoint Test AQ |
| SOBDMC | P1A0E:61 | Hybrid Powertrain Control Module - Motor Disabled: Signal Calculation Failure | GO to Pinpoint Test H |
| SOBDMC | P1A0E:62 | Hybrid Powertrain Control Module - Motor Disabled: Signal Compare Failure | GO to Pinpoint Test AM |
| SOBDMC | P1A0E:64 | Hybrid Powertrain Control Module - Motor Disabled: Signal Plausibility Failure | GO to Pinpoint Test AM |
| SOBDMC | P1A0E:96 | Hybrid Powertrain Control Module - Motor Disabled: Component Internal Failure | GO to Pinpoint Test AM |
| SOBDMC | P2531:00 | Ignition Switch Run Position Circuit Low: No Sub Type Information | GO to Pinpoint Test BK |
| SOBDMC | P2533:1F | Ignition Switch On/Start Position Circuit: Circuit Intermittent | GO to Pinpoint Test BK |
| SOBDMC | P2533:62 | Ignition Switch On/Start Position Circuit: Signal Compare Failure | GO to Pinpoint Test AS |
| SOBDMC | P2C94:00 | Hybrid/EV Battery Contactor Control Supply Circuit Low: No Sub Type Information | GO to Pinpoint Test AR |
| SOBDMC | P2C95:00 | Hybrid/EV Battery Contactor Control Supply Circuit High: No Sub Type Information | GO to Pinpoint Test AR |
| SOBDMC | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AT |
| SOBDMC | U010F:00 | Lost Communication With Air Conditioning Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| SOBDMC | U0111:00 | Lost Communication With Battery Energy Control Module "A": No Sub Type Information | GO to Pinpoint Test AV |
| SOBDMC | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AW |
| SOBDMC | U0128:00 | Lost Communication With Park Brake Control Module: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AX |
| SOBDMC | U0143:00 | Lost Communication With Body Control Module "C": No Sub Type Information | GO to Pinpoint Test AY |
| SOBDMC | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AZ |
| SOBDMC | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test BA |
| SOBDMC | U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test BB |
| SOBDMC | U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test BC |
| SOBDMC | U0198:00 | Lost Communication With Telematic Control Module "A": No Sub Type Information | GO to Pinpoint Test BO |
| SOBDMC | U019B:00 | Lost Communication With Battery Charger Control Module "A": No Sub Type Information | GO to Pinpoint Test BP |
| SOBDMC | U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test BC |
| SOBDMC | U0298:00 | Lost Communication With DC/DC Converter Control Module "A": No Sub Type Information | GO to Pinpoint Test BD |
| SOBDMC | U0315:00 | Software Incompatibility with Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | U063B:87 | Lost Communication With Coolant Bypass Valve Actuator "A": Missing Message | GO to Pinpoint Test BQ |
| SOBDMC | U0647:00 | Lost Communication with Motor Electronics Coolant Pump "B": No Sub Type Information | GO to Pinpoint Test BR |
| SOBDMC | U069E:81 | Lost Communication with Coolant Heater "B": Invalid Serial Data Received | GO to Pinpoint Test BS |
| SOBDMC | U069E:87 | Lost Communication with Coolant Heater "B": Missing Message | GO to Pinpoint Test BS |
| SOBDMC | U1011:86 | Invalid Internal Control Module Monitoring Data Received from ECM/PCM: Signal Invalid | GO to Pinpoint Test BE |
| SOBDMC | U1012:86 | Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: Signal Invalid | GO to Pinpoint Test BF |
| SOBDMC | U1027:00 | ABS Control Module Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BJ |
| SOBDMC | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BG |
| SOBDMC | U301B:00 | Control Module Wake-up Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test BH |
| SOBDMC | U351B:00 | High Voltage System Interlock Circuit "D" Low: No Sub Type Information | GO to Pinpoint Test BI |
| SOBDMC | U351F:00 | High Voltage System Interlock Circuit "E" Low: No Sub Type Information | GO to Pinpoint Test AH |