LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Avalon XLE Plus >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim (Service Information) (Except Hybrid) >> Instrument Panel Safety Pad >> Removal [10/2014 - ] >> Procedure

Removal [10/2014 - ]: Procedure

  1. PRECAUTION 

    (Refer to PRECAUTION [10/2014 - ] )

    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Refer to PRECAUTION [10/2014 - ] ).

  2. REMOVE HORN BUTTON ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

  3. REMOVE STEERING WHEEL ASSEMBLY 

    Refer to PROCEDURE - Step 3 Refer to PROCEDURE - Step 3

  4. REMOVE LOWER STEERING COLUMN COVER 

    Refer to PROCEDURE - Step 7

  5. REMOVE UPPER STEERING COLUMN COVER 

    Refer to PROCEDURE - Step 8

  6. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9

  7. REMOVE REAR CONSOLE BOX ASSEMBLY 

    (Refer to REMOVAL [10/2014 - 10/2015] Refer to REMOVAL [10/2015 - ] )

  8. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 
    1. Disengage the 18 clips and 2 guides.
      GTY378355Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the instrument cluster finish panel assembly.
  9. REMOVE FRONT DOOR SCUFF PLATE LH 

    See step  4 See step  4

  10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH 

    See step  5 See step  5

  11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
    1. Disconnect the front door opening trim weatherstrip LH.
      GTY378353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE INSTRUMENT SIDE PANEL LH 
    1. Using a moulding remover, disengage the 2 claws and clip as shown in the illustration.
      GTY378354Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
      GTY378358Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 
    1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
      GTY378352Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY 
    1. Remove the bolt <B> and screw <D>.
      GTY378351Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 8 clips and 5 claws.
      GTY378350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect each connector and remove the lower No. 1 instrument panel sub-assembly.
  15. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY 
    1. Disengage the 8 clips and remove the No. 1 instrument panel garnish sub-assembly.
      GTY378349Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. DISCONNECT NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH (w/ Illumination) 

    Refer to PROCEDURE - Step 10

  17. REMOVE NO. 1 INSTRUMENT PANEL STAY SUB-ASSEMBLY (w/ Illumination) 
    1. Disengage the 2 clips and remove the No. 1 instrument panel stay sub-assembly.
      GTY448991Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Disengage the 4 clips and 2 guides and remove the No. 1 instrument panel register assembly.
      GTY378334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (w/o Illumination) 
    1. Disengage the 3 clips and remove the No. 1 instrument cluster finish panel garnish.
      GTY378335Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (w/ Illumination) 
    1. Disengage the 3 clips.
      GTY378335Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp and remove the No. 1 instrument cluster finish panel garnish.
      GTY448992Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH (w/ Illumination) 

    Refer to PROCEDURE - Step 14

  22. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type) 

    Refer to PROCEDURE - Step 3

  23. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type) 

    Refer to PROCEDURE - Step 5

  24. REMOVE COMBINATION METER ASSEMBLY 

    Refer to PROCEDURE - Step 8

  25. REMOVE FRONT PILLAR GARNISH LH 

    See step  7 See step  7

  26. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  27. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  28. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Disconnect the front door opening trim weatherstrip RH.
      GTY378337Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE FRONT PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  30. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH 
    1. Pull the No. 1 defroster nozzle garnish in the direction indicated by the arrow (1) to disengage the 10 clips.
      GTY588643Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pull the No. 1 defroster nozzle garnish in the direction indicated by the arrow (2) to disengage the 10 guides.
    3. Disconnect the connector and remove the No. 1 defroster nozzle garnish.
  31. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY 

    Refer to PROCEDURE - Step 6

  32. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (except 8 Speakers) 

    Refer to PROCEDURE - Step 7

  33. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
    1. Disengage the 4 claws and 2 guides.
      GTY378331Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect each connector and remove the No. 2 instrument panel under cover sub-assembly.
  34. REMOVE INSTRUMENT SIDE PANEL RH 
    1. Using a moulding remover, disengage the 3 claws as shown in the illustration.
      GTY378330Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 3 guides and remove the instrument side panel RH as shown in the illustration.
      GTY378332Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE GLOVE COMPARTMENT PLATE 
    1. Disengage the 4 clips and remove the glove compartment plate.
      GTY383982Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 9

  37. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY 
    1. Apply protective tape to the area shown in the illustration.
      GTY378405Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Remove the 5 screws <D>.
      GTY378404Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 3 claws as shown in the illustration.
      GTY378403Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disconnect each connector and disengage the clamp.
      GTY378396Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the glove box light as shown in the illustration.
      GTY378390Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. REMOVE GLASS BREAKAGE SENSOR ECU (w/ Glass Breakage Sensor) 

    Refer to PROCEDURE - Step 3

  39. REMOVE REMOTE ENGINE STARTER ECU WITH BRACKET (w/ Remote Engine Starter System) 

    Refer to PROCEDURE - Step 3

  40. REMOVE GLASS BREAKAGE SENSOR ECU WITH REMOTE ENGINE STARTER ECU (for Glass Breakage Sensor with Remote Engine Starter System) 

    Refer to PROCEDURE - Step 4

  41. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY 
    1. Remove the 2 screws <D>.
      GTY378388Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 14 clips and remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.
      GTY378389Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  42. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY RH (w/ Illumination) 

    Refer to PROCEDURE - Step 21

  43. REMOVE INSTRUMENT PANEL STAY SUB-ASSEMBLY (w/ Illumination) 
    1. Disengage the 2 clips and remove the instrument panel stay sub-assembly.
      GTY449002Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  44. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Disengage the 4 clips and 2 guides and remove the No. 4 instrument panel register assembly.
      GTY378387Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH 
    1. Disengage the 9 clips.
      GTY378385Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the No. 2 instrument cluster finish panel garnish.
  46. REMOVE FRONT CONSOLE BOX 
    1. Remove the screw <D>.
      GTY378367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 clips and 4 guides and remove the front console box as shown in the illustration.
      GTY378368Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  47. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE 

    Refer to PROCEDURE - Step 3

  48. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 
    1. Disconnect each connector.
      GTY595135Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Room Temperature Sensor - -
    2. Disengage the 2 claws to disconnect the room temperature sensor.
    3. Disengage each clamp.
    4. Remove the 2 instrument panel passenger airbag assembly bolts <A>.
      GTY588342Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Instrument Panel Passenger Airbag Assembly Bolt <A> *b Bolt <B>
      *c Bolt <C> *d Nut <E>
      *e Clip - -
    5. Remove the 4 bolts <B>, bolt <C> and nut <E>.
    6. Remove the 2 clips.
    7. Disengage the 5 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.
      GTY378364Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Do not damage the instrument panel safety pad sub-assembly.
      • Do not allow the wire harnesses to interfere with the surrounding parts.
scientia non olet · About LEMON Manuals