Section 11 (Rear Axle - Lancer RALLIART, Se)
WARNING: This page is about a different variant/trim than selected.
- General Information
- General Specifications
- Service Specifications
- Lubricants
- Sealant And Adhesive
- Component Identification
- Rear Axle Diagnosis
- Introduction
- Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Noise during Wheel Rotation < DRIVESHAFT >
- INSPECTION PROCEDURE 2: Constant Noise < DIFFERENTIAL >
- INSPECTION PROCEDURE 3: Gear Noise while Driving < DIFFERENTIAL >
- INSPECTION PROCEDURE 4: Gear Noise while Coasting < DIFFERENTIAL >
- INSPECTION PROCEDURE 5: Bearing Noise while Driving or Coasting < DIFFERENTIAL >
- INSPECTION PROCEDURE 6: Noise while Turning < DIFFERENTIAL >
- INSPECTION PROCEDURE 7: Heat < DIFFERENTIAL >
- INSPECTION PROCEDURE 8: Oil Leakage < DIFFERENTIAL >
- Special Tools
- On-Vehicle Service
- Rear Axle Hub Assembly
- Driveshaft Assembly
- Differential Carrier Assembly
- Removal And Installation
- DISASSEMBLY < Type A >
- Notes
- Disassembly Service Points
- Drive Gear Backlash
- Drive Gear RUNOUT
- Final Drive Gear Tooth Contact
- Notes
- << B >> Differential Case Assembly/Differential Side Bearing Spacer/Differential Side Bearing Outer Race Removal
- << C >> Differential Side Bearing Inner Race Removal
- << D >> Drive Gear Removal
- << E >> Self-Locking Nut Removal
- << F >> Drive Pinion Assembly/Companion Flange Removal
- << G >> Drive Pinion Rear Bearing Inner Race Removal
- << H >> Drive Pinion Front Bearing Outer Race Removal
- << I >> Drive Pinion Rear Bearing Outer Race Removal
- DISASSEMBLY < Type B >
- Notes
- Disassembly Service Point
- Drive Gear Backlash
- Drive Gear RUNOUT On Backside
- Differential Gear Backlash
- Final Drive Gear Teeth Contact Adjustment
- Notes
- << B >> Differential Case Assembly/Differential Side Bearing Spacer/Differential Side Bearing Outer Race Removal
- << C >> Differential Side Bearing Inner Race Removal
- << D >> Drive Gear Removal
- << E >> Lock Pin Driving Out
- << F >> Differential Nut Removal
- << G >> Drive Pinion Rear Bearing Inner Race Removal
- << H >> Drive Pinion Front Bearing Outer Race Removal
- << I >> Drive Pinion Rear Bearing Outer Race Removal
- ASSEMBLY < Type A >
- Notes
- Lubrication And Adhesive Points
- Assembly Service Points
- >> A << Oil Seal Press-Fitting
- >> B << Drive Pinion Rear Bearing Outer Race Press-Fitting
- >> C << Drive Pinion Front Bearing Outer Race Press-Fitting
- >> D << Drive Pinion Height Adjustment
- >> E << Drive Pinion Turning Torque Adjustment/Oil Seal Installation
- >> F << Drive Gear Installation
- >> G << Differential Side Bearing Inner Race Installation
- >> H << Final Drive Gear Backlash Adjustment
- ASSEMBLY < Type B >
- Notes
- Lubricant/Sealant Application Points
- Assembly Service Point
- >> A << Drive Pinion Rear Bearing Outer Race Press-Fitting
- >> B << Drive Pinion Front Bearing Outer Race Press-Fitting
- >> C << Drive Pinion Height Adjustment
- >> D << Drive Pinion Rotation Torque Adjustment/Oil Seal Press-Fitting
- >> E << Differential Gear Backlash Adjustment
- >> F << Lock Pin Installation
- >> G << Drive Gear Installation
- >> H << Differential Side Bearing Inner Race Installation
- >> I << Final Drive Gear Backlash Adjustment
- >> J << Oil Seal Press-Fitting
- LSD Case Assembly Disassembly And Assembly
- LSD Case Assembly Inspection