Section 120 (Chassis Electrical - Lancer Evolution (1 Of 5))
WARNING: This page is about a different car, the 2008 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
- Battery
- Ignition Switch
- Combination Meter
- Service Specifications
- Special Tools
- Troubleshooting
- Standard Flow Of Diagnostic Troubleshooting
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Malfunction Of Odometer
- DTC B1201: Abnormal Fuel Information
- DTC B1208: Malfunction Of LCD Heater
- DTC B1209: Test Mode
- DTC B2203: VIN Not Programmed
- DTC B2463: The Sticking Of Rheostat Switch
- DTC B2464: The Sticking Of Multi Information Meter Switch
- DTC B2465: Ignition Switch Signal Error
- DTC U0019: Bus Off (Can-B)
- DTC U0100: Engine Control Module Can Timeout
- DTC U0141: ETACS Can Timeout
- DTC U0151: SRS-Ecu Can Timeout
- DTC U0154: Occupant Classification-Ecu Can Timeout
- DTC U0164: A/C-Ecu Can Timeout
- DTC U0168: Kos-Ecu Or WCM Can Timeout
- DTC U0184: Audio Can Timeout
- DTC U0197: Hands Free Module Can Timeout
- DTC U0245: Audio Visual Navigation Unit Can Timeout
- DTC U1415: Coding Not Completed/Data Fail
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: Power Supply Circuit Check
- Inspection Procedure 2: The Speedometer Does Not Work (The Other Meters Work)
- Inspection Procedure 3: The Tachometer Does Not Work (The Other Meters Work)
- Inspection Procedure 4: Tone Alarm Does Not Sound Normally
- Notes
- Technical Description (Comment)
- Seat belt reminder function
- Keyless operation key reminder tone alarm function (vehicles with KOS)
- Ignition key reminder tone alarm function (vehicles without KOS)
- Light reminder tone alarm function
- Door-ajar warning tone alarm function
- Freeze warning tone alarm
- Parking brake reminder tone alarm function
- Multi information display interrupt display tone alarm
- Multi information meter switch operation tone alarm
- Turn-signal light tone alarm function
- Paddle shift cancel tone alarm, Theft-alarm function, ETACS-ECU function customize tone alarm, A/C operation tone alarm, audio operation tone alarm
- Troubleshooting Hints
- Diagnosis
- Inspection Procedure 5: The Combination Meter Light Does Not Illuminate Normally Or The Multi Information Display Is Not Displayed Normally
- Inspection Procedure 6: The Multi Information Display Screen Cannot Be Changed With The Operation Of The Multi Information Meter Switch
- Service Data
- Actuator Test Table
- Check Procedure For Each Multi Information Display Screen
- Check At Ecu Terminals
- On-Vehicle Service
- Speedometer Check
- Tachometer Check
- Fuel Level Sensor Check
- Multi Information Meter Switch Check
- Service Reminder Function Set
- How To Set By Operating The Scan Tool MB991958
- How To Operate The Scan Tool MB991958
- 1. Reminder Reset (Indicator Off)
- 2. Next Schedule Reminder Cancel
- 3. Extra Reminder Setting
- 4. Extra Reminder Cancel
- 5. Periodic Reminder Schedule Set
- 6. Integrated Value Adjustment
- 7. Optional Int Schedule Setting
- How To Set By Special Operation Of Switch
- How To Cancel The Service Reminder Warning
- How To Set The Schedule
- Schedule Table
- How To Inactivate The Service Reminder Function
- Combination Meter
- Headlight
- General Information
- Service Specifications
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: All The Headlights (Low-Beam) Do Not Illuminate
- Inspection Procedure 2: All The Headlights (High-Beam) Do Not Illuminate
- Inspection Procedure 3: The Headlights Illuminate At Low-Beam (High-Beam Does Not Illuminate) Regardless Of The Lighting Switch Positions
- Inspection Procedure 4: Headlights Do Not Illuminate When The Passing Switch Is Operated
- Inspection Procedure 5: One Of The Headlights Does Not Illuminate
- Inspection Procedure 6: High-Beam Indicator Light Does Not Illuminate Normally
- Inspection Procedure 7: The Headlight Automatic Shutdown Function Does Not Work Normally
- Inspection Procedure 8: Daytime Running Light Function Does Not Work Normally < Halogen Type Headlight >
- Inspection Procedure 8: Daytime Running Light Function Does Not Work Normally < Discharge Type Headlight >
- Inspection Procedure 9: Any Of The Tail Lights, The Position Lights Or The License Plate Lights Does Not Illuminate
- Inspection Procedure 10: The Auto Light Function Does Not Work Normally
- Inspection Procedure 11: All The Turn-Signal Lights Do Not Illuminate
- Inspection Procedure 12: The Comfort Flashing Function Does Not Work Normally
- Inspection Procedure 13: The Turn-Signal Indicator Light Do Not Illuminate
- Data List Reference Table
- On-Vehicle Service
- Headlight Aiming
- Luminous Intensity Measurement
- Replace The Bulb
- Headlight Bulb (Low-Beam) Replacement < Vehicles Without Discharge Headlight >
- Headlight Bulb (High-Beam) Replacement < Vehicles Without Discharge Headlight >
- Daytime Running Light Bulb Replacement < Vehicles With Discharge Headlight >
- Position Light Bulb Replacement
- Front Turn-Signal Light Bulb Replacement
- Headlight Automatic-Shutdown Function Check
- Headlight Auto Light Function Check
- Customization Function
- Headlight Removal And Installation
- Headlight Leveling Switch Removal And Installation
- Lighting Control Sensor Removal And Installation
- Inspection
- Headlight Leveling Switch Check < Vehicles With Headlight Manual Leveling System >
- Lighting Control Sensor (Light Sensor) Check