Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2020 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| TCM | P0603:00 | Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P0604:00 | Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P0605:00 | Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P0607:00 | Control Module Performance: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P060A:00 | Internal Control Module Monitoring Processor Performance: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P060B:00 | Internal Control Module A/D Processing Performance: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P060C:00 | Internal Control Module Main Processor Performance: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P061A:00 | Internal Control Module Torque Performance: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P062C:00 | Internal Control Module Vehicle Speed Performance: No Sub Type Information | GO to Pinpoint Test J |
| TCM | P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P0657:00 | Actuator Supply Voltage "A"Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P068A:00 | ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P06B8:00 | Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P0702:00 | Transmission Control System Electrical: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0706:00 | Transmission Range Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P0707:00 | Transmission Range Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P0708:00 | Transmission Range Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P0709:00 | Transmission Range Sensor "A" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P0710:00 | Transmission Fluid Temperature Sensor "A" Circuit: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0711:00 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0712:00 | Transmission Fluid Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0713:00 | Transmission Fluid Temperature Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0715:00 | Input/Turbine Shaft Speed Sensor "A" Circuit: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0716:00 | Input/Turbine Shaft Speed Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P0717:00 | Input/Turbine Shaft Speed Sensor "A" Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0718:00 | Input/Turbine Shaft Speed Sensor "A" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0720:00 | Output Shaft Speed Sensor Circuit: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0721:00 | Output Shaft Speed Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P0722:00 | Output Shaft Speed Sensor Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0723:00 | Output Shaft Speed Sensor Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0729:00 | Gear 6 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P0731:00 | Gear 1 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P0732:00 | Gear 2 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P0733:00 | Gear 3 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P0734:00 | Gear 4 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test P |
| TCM | P0735:00 | Gear 5 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test Q |
| TCM | P0736:00 | Reverse Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test R |
| TCM | P0740:00 | Torque Converter Clutch Solenoid Circuit/Open: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0741:00 | Torque Converter Clutch Solenoid Circuit Performance Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P0743:00 | Torque Converter Clutch Solenoid Circuit Electrical: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0748:00 | Pressure Control Solenoid "A" Electrical: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0751:00 | Shift Solenoid "A" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P0752:00 | Shift Solenoid "A" Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P0753:00 | Shift Solenoid "A" electrical: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0754:00 | Shift Solenoid "A" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0756:00 | Shift Solenoid "B" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P0757:00 | Shift Solenoid "B" Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P0758:00 | Shift Solenoid "B" electrical: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0759:00 | Shift Solenoid "B" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0761:00 | Shift Solenoid "C" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P0762:00 | Shift Solenoid "C" Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P0763:00 | Shift Solenoid "C" electrical: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0764:00 | Shift Solenoid "C" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0766:00 | Shift Solenoid "D" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P0767:00 | Shift Solenoid "D" Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P0768:00 | Shift Solenoid "D" electrical: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0769:00 | Shift Solenoid "D" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P076F:00 | Gear 7 Ratio Incorrect: No Sub Type Information | GO to Pinpoint Test U |
| TCM | P0771:00 | Shift Solenoid "E" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P0772:00 | Shift Solenoid "E" Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P0773:00 | Shift Solenoid "E" electrical: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0774:00 | Shift Solenoid "E" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P077D:00 | Output Shaft Speed Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0791:00 | Intermediate Shaft Speed Sensor "A" Circuit: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0792:00 | Intermediate Shaft Speed Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P0793:00 | Intermediate Shaft Speed Sensor "A" Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0794:00 | Intermediate Shaft Speed Sensor "A" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07BF:00 | Input/Turbine Shaft Speed Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07C0:00 | Input/Turbine Shaft Speed Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07C5:00 | Intermediate Shaft Speed Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07C6:00 | Intermediate Shaft Speed Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07C7:00 | Intermediate Shaft Speed Sensor "B" Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07C8:00 | Intermediate Shaft Speed Sensor "B" Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P07D9:00 | Gear 8 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P07F6:00 | Gear 9 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P07F7:00 | Gear 10 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test X |
| TCM | P0868:00 | Transmission Fluid Pressure Low: No Sub Type Information | GO to Pinpoint Test Y |
| TCM | P0882:00 | TCM Power Input Signal Low: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0883:00 | TCM Power Input Signal High: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0884:00 | TCM Power Input Signal Intermittent: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0960:00 | Pressure Control Solenoid "A" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0961:00 | Pressure Control Solenoid "A" Control Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0962:00 | Pressure Control Solenoid "A" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0963:00 | Pressure Control Solenoid "A" Control Circuit High: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0973:00 | Shift solenoid "A" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0974:00 | Shift solenoid "A" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0976:00 | Shift solenoid "B" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0977:00 | Shift solenoid "B" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0979:00 | Shift solenoid "C" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P097A:00 | Shift solenoid "A" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P097B:00 | Shift solenoid "B" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P097C:00 | Shift solenoid "C" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P097D:00 | Shift solenoid "D" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P097E:00 | Shift solenoid "E" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P097F:00 | Shift solenoid "F" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0980:00 | Shift solenoid "C" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0982:00 | Shift solenoid "D" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0983:00 | Shift solenoid "D" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0985:00 | Shift solenoid "E" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0986:00 | Shift solenoid "E" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0998:00 | Shift solenoid "F" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0999:00 | Shift solenoid "F" Control Circuit High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0B0D:00 | Electric/Auxiliary Transmission Fluid Pump Motor Control Module: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0C27:00 | Electric/Auxiliary Transmission Fluid Pump "A" Motor Current Low: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0C28:00 | Electric/Auxiliary Transmission Fluid Pump "A" Motor Current High: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0C29:00 | Electric/Auxiliary Transmission Fluid Pump "A" Driver Circuit Performance: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0C2A:00 | Electric/Auxiliary Transmission Fluid Pump "A" Motor Stalled: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0C2C:00 | Electric Transmission Fluid Pump Control Module Feedback Signal Range/Performance: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0C2D:00 | Electric Transmission Fluid Pump Control Module Feedback Signal Low: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0C2E:00 | Electric Transmission Fluid Pump Control Module Feedback Signal High: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P1001:00 | KOER Not Able to Complete, KOER Aborted: No Sub Type Information | GO to Pinpoint Test Z |
| TCM | P1397:00 | System Voltage Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P1501:00 | Vehicle Speed Sensor Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test Z |
| TCM | P160A:00 | Control Module Vehicle Options Reconfiguration Error: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P1636:00 | Inductive Signature Chip Communication Error: No Sub Type Information | GO to Pinpoint Test AA |
| TCM | P163E:00 | Transmission Control Module Programming Error: No Sub Type Information | GO to Pinpoint Test AA |
| TCM | P163F:00 | Transmission ID Block Corrupted, Not Programmed: No Sub Type Information | GO to Pinpoint Test AA |
| TCM | P1674:00 | Control Module Software Corrupted: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P1705:00 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P1711:00 | Transmission Fluid Temperature Sensor Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test AB |
| TCM | P1744:00 | Torque Converter Clutch Solenoid Circuit Performance: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P175A:00 | Transmission Fluid Over Temperature Condition - Electric Transmission Fluid Pump Disabled: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P1783:00 | Transmission Fluid Over Temperature Condition: No Sub Type Information | GO to Pinpoint Test AC |
| TCM | P1A02:00 | Transmission One Way Clutch Performance: No Sub Type Information | GO to Pinpoint Test AD |
| TCM | P2531:00 | Ignition Switch Run Position Circuit Low: No Sub Type Information | GO to Pinpoint Test AE |
| TCM | P2532:00 | Ignition Switch Run Position Circuit High: No Sub Type Information | GO to Pinpoint Test AE |
| TCM | P2669:00 | Actuator Supply Voltage "B" Circuit/Open: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P26C3:00 | Internal Control Module Transmission Range Sensor Performance: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P2700:00 | Transmission Friction Element "A" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AF |
| TCM | P2701:00 | Transmission Friction Element "B" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AF |
| TCM | P2702:00 | Transmission Friction Element "C" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AF |
| TCM | P2703:00 | Transmission Friction Element "D" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AF |
| TCM | P2704:00 | Transmission Friction Element "E" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AF |
| TCM | P2705:00 | Transmission Friction Element "F" Apply Time Range Performance: No Sub Type Information | GO to Pinpoint Test AF |
| TCM | P2707:00 | Shift Solenoid "F" Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test S |
| TCM | P2708:00 | Shift Solenoid "F" Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P2709:00 | Shift Solenoid "F" Electrical: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P2710:00 | Shift Solenoid "F" Intermittent: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P2745:00 | Intermediate Shaft Speed Sensor "B" Circuit: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2746:00 | Intermediate Shaft Speed Sensor "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2747:00 | Intermediate Shaft Speed Sensor "B" Circuit No Signal: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2748:00 | Intermediate Shaft Speed Sensor "B" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2758:00 | Torque Converter Clutch Pressure Control Solenoid Stuck On: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P2760:00 | Torque Converter Clutch Pressure Control Solenoid Intermittent: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P2769:00 | Torque Converter Clutch Circuit Low: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P2770:00 | Torque Converter Clutch Circuit High: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P2783:00 | Torque Converter Temperature Too High: No Sub Type Information | GO to Pinpoint Test T |
| TCM | P2796:00 | Electric Transmission Fluid Pump Control Circuit: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P27B2:00 | Internal Control Module Transmission Range Control Performance: No Sub Type Information | GO to Pinpoint Test AG |
| TCM | P27B3:00 | Internal Control Module Transmission Gear Select Performance: No Sub Type Information | GO to Pinpoint Test AG |
| TCM | P27B4:00 | Internal Control Module Transmission Gear Direction Control Performance: No Sub Type Information | GO to Pinpoint Test AG |
| TCM | P27B5:00 | Internal Control Module Transmission Gear Ratio Control Performance: No Sub Type Information | GO to Pinpoint Test AG |
| TCM | P27B6:00 | Internal Control Module Transmission Speed Sensor Performance: No Sub Type Information | GO to Pinpoint Test AG |
| TCM | P2801:00 | Transmission Range Sensor "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P2802:00 | Transmission Range Sensor "B" Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P2803:00 | Transmission Range Sensor "B" Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P2804:00 | Transmission Range Sensor "B" Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P2805:00 | Transmission Range Sensor "A"/ "B" Correlation: No Sub Type Information | GO to Pinpoint Test C |
| TCM | U0028:00 | Vehicle Communication Bus A: No Sub Type Information | GO to Pinpoint Test AH |
| TCM | U0037:00 | Vehicle Communication Bus B: No Sub Type Information | GO to Pinpoint Test AH |
| TCM | U0073:00 | Control Module Communication Bus "A" Off: No Sub Type Information | GO to Pinpoint Test AH |
| TCM | U0074:00 | Control Module Communication Bus "B" Off: No Sub Type Information | GO to Pinpoint Test AH |
| TCM | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AI |
| TCM | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AJ |
| TCM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AK |
| TCM | U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test AL |
| TCM | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AM |
| TCM | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AI |
| TCM | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AJ |
| TCM | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AK |
| TCM | U1011:00 | Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information | GO to Pinpoint Test AI |
| TCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test I |
| TCM | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test I |
| TCM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test I |