Section 10 (Engine Mechanical - 8.1L)
WARNING: This page is about a different variant/trim than selected.
- Specifications
- Component Locator
- Diagnostic Information and Procedures
- Diagnostic Starting Point - Engine Mechanical
- Symptoms - Engine Mechanical
- Base Engine Misfire without Internal Engine Noises
- Base Engine Misfire with Abnormal Internal Lower Engine Noises
- Base Engine Misfire with Abnormal Valve Train Noise
- Base Engine Misfire with Coolant Consumption
- Base Engine Misfire with Excessive Oil Consumption
- Engine Noise on Start-Up, but Only Lasting a Few Seconds
- Upper Engine Noise, Regardless of Engine Speed
- Lower Engine Noise, Regardless of Engine Speed
- Engine Noise Under Load
- Engine Will Not Crank - Crankshaft Will Not Rotate
- Coolant in Combustion Chamber
- Coolant in Engine Oil
- Engine Compression Test
- Cylinder Leakage Test
- Oil Consumption Diagnosis
- Oil Pressure Diagnosis and Testing
- Oil Leak Diagnosis
- Crankcase Ventilation System Inspection/Diagnosis
- Drive Belt Chirping Diagnosis
- Drive Belt Squeal Diagnosis
- Drive Belt Whine Diagnosis
- Drive Belt Rumbling Diagnosis
- Drive Belt Vibration Diagnosis
- Drive Belt Falls Off Diagnosis
- Drive Belt Excessive Wear Diagnosis
- Drive Belt Tensioner Diagnosis
- Repair Instructions
- On-Vehicle Repair Instructions
- Drive Belt Replacement - Accessory
- Drive Belt Replacement - Air Conditioning
- Drive Belt Tensioner Replacement - Accessory
- Drive Belt Tensioner Replacement - Air Conditioning
- Drive Belt Idler Pulley Replacement
- Engine Mount Inspection
- Engine Mount Replacement - Left
- Engine Mount Replacement - Right
- Engine Sight Shield Replacement
- Intake Manifold Replacement
- Valve Rocker Arm Cover Replacement - Left
- Valve Rocker Arm Cover Replacement - Right
- Valve Rocker Arm and Push Rod Replacement
- Valve Stem Oil Seal and Valve Spring Replacement
- Valve Lifter Replacement
- Oil Level Indicator and Tube Replacement
- Cylinder Head Replacement - Left
- Cylinder Head Replacement - Right
- Crankshaft Balancer Replacement
- Crankshaft Front Oil Seal Replacement
- Engine Front Cover Replacement
- Timing Chain and Sprockets Replacement
- Oil Pump Drive Replacement
- Camshaft Replacement
- Oil Filter Adapter and Bypass Valve Assembly Replacement
- Oil Pan Replacement
- Engine Oil Pressure Sensor and/or Switch Replacement
- Engine Oil Level Sensor and/or Switch Replacement
- Oil Pump Replacement
- Crankshaft Rear Oil Seal Replacement
- Engine Flywheel Replacement
- Engine Replacement
- Engine Oil and Oil Filter Replacement
- Off-Vehicle Repair Instructions
- Draining Fluids and Oil Filter Removal
- Crankshaft Balancer Removal
- Engine Flywheel Removal (Automatic Transmission)
- Engine Flywheel Removal (Manual Transmission)
- Crankshaft Rear Oil Seal Removal
- Clutch Pilot Bearing Removal
- Oil Level Indicator and Tube Removal
- Exhaust Manifold Removal - Left
- Exhaust Manifold Removal - Right
- Water Crossover Removal
- Water Pump Removal
- Intake Manifold Removal
- Valve Rocker Arm Cover Removal - Left
- Valve Rocker Arm Cover Removal - Right
- Valve Rocker Arm and Push Rod Removal
- Cylinder Head Removal - Left
- Cylinder Head Removal - Right
- Valve Lifter Removal
- Oil Pump Drive Removal
- Oil Pan Removal
- Oil Pump, Screen and Crankshaft Oil Deflector Removal
- Engine Front Cover Removal
- Timing Chain and Sprockets Removal
- Camshaft Removal
- Piston, Connecting Rod, and Bearing Removal
- Crankshaft and Bearings Removal
- Oil Filter Adapter Removal
- Engine Block Plug Removal
- Camshaft Bearing Removal
- Engine Block Cleaning and Inspection
- Cylinder Boring and Honing
- Crankshaft and Bearings Cleaning and Inspection
- Notes
- Crankshaft Inspection
- Crankshaft and Connecting Rod Bearing Inspection
- Crankshaft and Connecting Rod Bearing Clearance Measurement
- Micrometer Method for Crankshaft Bearings
- Micrometer Method for Connecting Rod Bearings
- Plastic Gage Method for Crankshaft Bearings
- Plastic Gage Method for Connecting Rod Bearings
- Measuring Crankshaft End Play
- Measuring Connecting Rod Side Clearance
- Measuring Connecting Rod Bearing Clearance - Using J 43690/J 43690-100
- Crankshaft Balancer Cleaning and Inspection
- Engine Flywheel Cleaning and Inspection (Automatic Transmission)
- Engine Flywheel Cleaning and Inspection (Manual Transmission)
- Piston and Connecting Rod Disassemble
- Piston, Connecting Rod, and Bearings Cleaning and Inspection
- Piston and Connecting Rod Assemble
- Camshaft and Bearings Cleaning and Inspection
- Camshaft Bearing Installation
- Timing Chain and Sprockets Cleaning and Inspection
- Valve Rocker Arm and Push Rods Cleaning and Inspection
- Valve Lifters and Guides Cleaning and Inspection
- Cylinder Head Disassemble
- Cylinder Head Cleaning and Inspection
- Valve Guide Reaming/Valve and Seat Grinding
- Cylinder Head Assemble
- Oil Pump Disassemble
- Oil Pump Cleaning and Inspection
- Oil Pump Assemble
- Oil Pump Drive Cleaning and Inspection
- Valve Rocker Arm Cover Cleaning and Inspection
- Oil Pan Cleaning and Inspection
- Intake Manifold Disassemble
- Intake Manifold Cleaning and Inspection
- Intake Manifold Assemble
- Exhaust Manifold Cleaning and Inspection
- Water Crossover Cleaning and Inspection
- Water Pump Cleaning and Inspection
- Thread Repair
- Service Prior to Assembly
- Engine Block Plug Installation
- Oil Filter Adapter Installation
- Crankshaft and Bearings Installation
- Piston, Connecting Rod, and Bearing Installation
- Camshaft Installation
- Timing Chain and Sprockets Installation
- Engine Front Cover Installation
- Oil Pump, Screen and Crankshaft Oil Deflector Installation
- Oil Pan Installation
- Oil Pump Drive Installation
- Valve Lifter Installation
- Cylinder Head Installation - Left
- Cylinder Head Installation - Right
- Valve Rocker Arm and Push Rod Installation
- Intake Manifold Installation
- Valve Rocker Arm Cover Installation - Left
- Valve Rocker Arm Cover Installation - Right
- Water Pump Installation
- Water Crossover Installation
- Exhaust Manifold Installation - Left
- Exhaust Manifold Installation - Right
- Oil Level Indicator and Tube Installation
- Clutch Pilot Bearing Installation
- Crankshaft Rear Oil Seal Installation
- Engine Flywheel Installation (Automatic Transmission)
- Engine Flywheel Installation (Manual Transmission)
- Crankshaft Balancer Installation
- Engine Prelubing
- On-Vehicle Repair Instructions
- Description and Operation
- Special Tools and Equipment