LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Highlander Limited, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 14 (Transfer Case -MF2A) >> Transfer Case Oil Seal >> Installation

Transfer Case Oil Seal: Installation

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL TRANSFER CASE OIL SEAL 
    1. Using SST, install a new transfer case oil seal to the transfer case at the position shown in the illustration.

      SST 09387-00010, 09950-70010 (09951 -07150) 

      NOTE:
      • Do not install the oil seal obliquely.
      • Do not damage the oil seal lip.
    2. Apply small amount of MP grease to the oil seal lip.
    Fig 1: Installing Transfer Case Oil Seal
    G05417048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL CENTER DIFFERENTIAL LOCK SLEEVE  (See INSTALLATION )
  3. INSTALL TRANSFER ASSEMBLY  (See INSTALLATION )
  4. INSTALL AUTOMATIC TRANSAXLE WITH TRANSFER  (See INSTALLATION )
  5. INSTALL TRANSFER STIFFENER PLATE RH  (See INSTALLATION )
  6. CONNECT CONNECTORS  (See INSTALLATION )
  7. CONNECT WIRE HARNESS  (See INSTALLATION )
  8. INSTALL WIRE HARNESS CLAMP  (See INSTALLATION )
  9. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH  (See INSTALLATION )
  10. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)  (See INSTALLATION )
  11. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET  (See INSTALLATION )
  12. INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY  (See INSTALLATION )
  13. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR  (See INSTALLATION )
  14. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR  (See INSTALLATION )
  15. INSTALL FRONT FRAME ASSEMBLY  (See INSTALLATION )
  16. INSTALL POWER STEERING LINK ASSEMBLY (for 4WD)  (See INSTALLATION )
  17. INSTALL FRONT STABILIZER BAR  (See INSTALLATION )
  18. REMOVE ENGINE HANGERS  (See INSTALLATION )
  19. INSTALL MANIFOLD STAY  (See INSTALLATION )
  20. INSTALL STARTER ASSEMBLY  (See INSTALLATION )
  21. INSTALL ENGINE WIRE  (See INSTALLATION )
  22. INSTALL INTAKE AIR SURGE TANK ASSEMBLY  (See INSTALLATION )
  23. INSTALL VENTILATION HOSE  (See INSTALLATION )
  24. TEMPORARILY TIGHTEN COMPRESSOR AND MAGNETIC CLUTCH  (See INSTALLATION )
  25. INSTALL COMPRESSOR AND MAGNETIC CLUTCH  (See INSTALLATION )
  26. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE  (See INSTALLATION )
  27. RECONNECT SUCTION HOSE SUB-ASSEMBLY  (See INSTALLATION )
  28. RECONNECT DISCHARGE HOSE SUB-ASSEMBLY  (See INSTALLATION )
  29. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY  (See INSTALLATION )
  30. INSTALL FRONT AXLE ASSEMBLY LH  (See INSTALLATION )
  31. INSTALL FRONT AXLE ASSEMBLY RH  (See INSTALLATION )
  32. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH  (See INSTALLATION )
  33. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM RH  (See INSTALLATION )
  34. CONNECT TIE ROD ASSEMBLY LH  (See INSTALLATION )
  35. CONNECT TIE ROD ASSEMBLY RH  (See INSTALLATION )
  36. INSTALL FRONT SPEED SENSOR LH  (See INSTALLATION )
  37. INSTALL FRONT SPEED SENSOR RH  (See INSTALLATION )
  38. INSTALL FRONT AXLE HUB NUT LH  (See INSTALLATION )
  39. INSTALL FRONT AXLE HUB NUT RH  (See INSTALLATION )
  40. INSTALL FRONT STABILIZER LINK ASSEMBLY LH  (See INSTALLATION )
  41. INSTALL FRONT STABILIZER LINK ASSEMBLY RH  (See INSTALLATION )
  42. INSTALL FRONT EXHAUST PIPE ASSEMBLY  (See INSTALLATION )
  43. INSTALL NO. 3 FRONT EXHAUST PIPE SUB-ASSEMBLY  (See INSTALLATION )
  44. INSTALL CENTER EXHAUST PIPE ASSEMBLY  (See INSTALLATION )
  45. INSTALL TAIL EXHAUST PIPE ASSEMBLY  (See INSTALLATION )
  46. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY  (See INSTALLATION )
  47. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY  (See INSTALLATION )
  48. CONNECT ENGINE WIRE  (See INSTALLATION )
  49. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY  (See INSTALLATION )
  50. CONNECT FUEL TUBE SUB-ASSEMBLY  (See INSTALLATION )
  51. CONNECT OIL COOLER OUTLET HOSE  (See INSTALLATION )
  52. CONNECT OIL COOLER INLET HOSE  (See INSTALLATION )
  53. CONNECT HEATER WATER HOSE INLET B  (See INSTALLATION )
  54. CONNECT HEATER WATER HOSE OUTLET B  (See INSTALLATION )
  55. INSTALL NO. 1 RADIATOR HOSE  (See INSTALLATION )
  56. INSTALL NO. 2 RADIATOR HOSE  (See INSTALLATION )
  57. CONNECT UNION TO CHECK VALVE HOSE  (See INSTALLATION )
  58. CONNECT NO. 1 FUEL VAPOR FEED HOSE  (See INSTALLATION )
  59. INSTALL ENGINE MOVING CONTROL ROD  (See INSTALLATION )
  60. INSTALL NO. 2 ENGINE MOUNTING STAY RH  (See INSTALLATION )
  61. INSTALL RESERVOIR BRACKET  (See INSTALLATION )
  62. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY  (See INSTALLATION )
  63. INSTALL AIR CLEANER BRACKET  (See INSTALLATION )
  64. INSTALL BATTERY  (See INSTALLATION )
  65. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
    NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
  66. INSTALL AIR CLEANER CASE SUB-ASSEMBLY  (See ON-VEHICLE INSPECTION )
  67. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY  (See INSTALLATION )
  68. INSTALL AIR CLEANER CAP SUB-ASSEMBLY  (See INTAKE MANIFOLD )
  69. INSTALL NO. 1 AIR CLEANER INLET  (See INTAKE MANIFOLD )
  70. INSTALL NO. 2 AIR CLEANER INLET  (See COMPONENTS )
  71. CONNECT VACUUM HOSES  (See INSTALLATION )
  72. INSTALL V-RIBBED BELT  (See INSTALLATION )
  73. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY  (See INSTALLATION )
  74. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY  (See INSTALLATION )
  75. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  (See INSTALLATION )
  76. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH  (See INSTALLATION )
  77. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH  (See INSTALLATION )
  78. REMOVE FRONT WHEELS  (See INSTALLATION )
  79. ADD ENGINE OIL  (See OIL PRESSURE SWITCH )
  80. ADD ENGINE COOLANT  (See REMOVAL )
  81. INSTALL TRANSFER DRAIN PLUG  (See TRANSFER CASE OIL SEAL )
  82. INSTALL NO.2 TRANSFER CASE PLUG  (See TRANSFER CASE OIL SEAL )
  83. INSTALL NO.1 TRANSFER CASE PLUG  (See TRANSFER CASE OIL SEAL )
  84. ADD AUTOMATIC TRANSAXLE FLUID 
  85. CHECK AUTOMATIC TRANSAXLE FLUID  (See AUTOMATIC TRANSAXLE FLUID )
  86. INSPECT FOR FUEL LEAK  (See PARTS LOCATION )
  87. INSPECT FOR ENGINE OIL LEAK  (See OIL PRESSURE SWITCH )
  88. INSPECT FOR FOR COOLANT LEAK  (See COOLING SYSTEM )
  89. INSPECT FOR EXHAUST GAS LEAK  (See INSTALLATION )
  90. CHECK SHIFT LEVER POSITION  (See ON-VEHICLE INSPECTION )
  91. CHECK AND ADJUST FRONT WHEEL ALIGNMENT  (See INSTALLATION )
  92. CHECK IGNITION TIMING  (See ENGINE )
  93. CHECK ENGINE IDLE SPEED  (See ON-VEHICLE INSPECTION )
  94. CHECK CO/HC  (See ON-VEHICLE INSPECTION )
  95. CHECK FUNCTION OF THROTTLE BODY ASSEMBLY  (See INSPECTION PROCEDURE )
  96. INSTALL FRONT FENDER APRON SEAL LH  (See INSTALLATION )
  97. INSTALL FRONT FENDER APRON SEAL RH  (See INSTALLATION )
  98. INSTALL FRONT FENDER LINER LH  (See INSTALLATION )
  99. INSTALL FRONT FENDER LINER RH  (See INSTALLATION )
  100. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH  (See INSTALLATION )
  101. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH  (See INSTALLATION )
  102. INSTALL FLOOR UNDER COVER LH 
  103. INSTALL NO. 2 ENGINE UNDER COVER  (See INSTALLATION )
  104. INSTALL NO. 1 ENGINE UNDER COVER  (See INSTALLATION )
  105. INSTALL ENGINE UNDER COVER ASSEMBLY  (See INSTALLATION )
  106. INSTALL V-BANK COVER SUB-ASSEMBLY  (See INSTALLATION )
  107. CHECK ABS SPEED SENSOR SIGNAL  (See INSTALLATION )
  108. RESET MEMORY  (See INSTALLATION )
scientia non olet · About LEMON Manuals