LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Highlander Limited, FWD >> Repair and Diagnosis >> Drivelines & Axles >> Driveshaft & Universal Joints >> Propeller Shaft (Except Hybrid) >> Propeller Shaft Assembly >> Installation

Propeller Shaft Assembly: Installation

  1. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 
    1. Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.
      Fig 1: Identifying Matchmarks On Propeller Shaft Flange And Differential Companion Flange
      G05417055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove SST from the transaxle.
    3. Insert the yoke into the transaxle.
      Fig 2: Identifying SST On Transaxle
      G05417058Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.
      Fig 3: Locating Propeller With Center Bearing Shaft Assembly Bolts
      G05417056Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Tighten the 4 bolts.

      Torque: 74 N*m (750 kgf*cm, 54 ft.*lbf) 

    Fig 4: Identifying Matchmarks On Propeller Shaft Flange And Differential Companion Flange
    G05417055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 
    1. Remove the piece of cloth from the joint.
    2. Using a hexagon wrench (6 mm), tighten the 6 bolts.

      Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf) 

      Fig 5: Tightening Bolts
      G05417094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.

      (A): 58.0 +/- 0.5 mm (2.283 +/- 0.02 in.) 

      Fig 6: Identifying Dimension Between Rear Side Of Cover And Shaft
      G05417095Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.
      Fig 7: Identifying Dimensions Between Edge Surface Of Center Support Bearing And Edge Surface Of Cushion Respectively
      G05417096Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf) 

      (B): 12.5 +/- 1.0 mm (0.492 +/- 0.039 in.) 

    5. Check that the center line of the bracket is at the right angle in the shaft axial direction.
    6. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.
      1. Turn the propeller shaft several times by hand to stabilize the center support bearings.
      2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.
      3. Remove the transfer dynamic damper.
      4. Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).

        SST 09370-50010 

        No. 1 joint angle: (A)-(B) =-1.3° to -3.3° 

      5. Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

        SST 09370-50010 

        No. 2 joint angle: (C)-(D) =1.8° to 3.5° 

        Fig 8: Checking Joint Angle
        G05417097Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        HINT:

        If the measured angle is not within the specification, adjust it with the center support bearing adjusting shim.

        Center support bearing adjusting shim thickness 

        CENTER SUPPORT BEARING ADJUSTING SHIM THICKNESS REFERENCE

        Thickness mm (in.) Thickness mm (in.)
        3.2 (0.126) 11.0(0.433)
        4.5 (0.177) 13.5 (0.531)
        6.5 (0.256) 15.5 (0.610)
        9.0 (0.354) 17.5(0.689)
      6. Install the transfer dynamic damper.

        Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf) 

  3. INSPECT AND ADJUST TRANSFER OIL  (See TRANSFER OIL )
scientia non olet · About LEMON Manuals