Section 41 (Electronic Time & Alarm Control System (ETACS) - With Diagnostics)
WARNING: This page is about a different car, the 2014 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.
- Special Tool
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnosis Function
- Diagnostic Trouble Code Table
- Diagnostic Trouble Code Procedures
- DTC B1761: VIN not programmed
- DTC B1762: IOD fuse not seated fully
- DTC B210A: +B power supply (low); DTC B210B: +B power supply (high)
- DTC B2206: VIN error/Mismatch
- DTC B2215: ECU internal error (EEPROM)
- DTC B222C: Coding not completed
- DTC B2353: Ignition power supply (low); DTC B2354: Ignition power supply (high)
- DTC U1100: Engine CAN timeout
- DTC U0101: T/M CAN timeout
- DTC U0114 4WD CAN timeout
- DTC U0121: ABS/ASC CAN timeout
- DTC U0131: EPS CAN timeout
- DTC U0151: SRS-ABG CAN timeout
- DTC U0154: OCM CAN timeout
- DTC U0155: Meter CAN timeout
- DTC U0164: A/C CAN timeout
- DTC U0168: WCM/F.A.S.T. CAN timeout
- DTC U0184: AUDIO CAN timeout
- DTC U0230: Power Gate CAN timeout
- DTC U0245: NAVI/DISP.AUDIO CAN timeout
- DTC U1000: OSS CAN timeout
- DTC U15A0: ACC/FCM ECU CAN timeout
- DTC U15A1: LDW/RLS CAN timeout
- DTC U0331: ECU internal error (ROM)
- DTC U1073: Bus off (CAN-C-Mid)
- Data List Reference Table
- Notes
- Trouble Symptom Chart
- Symptom Procedures
- Input Signal Procedures
- Inspection Procedure 1: The ignition switch (ACC) signal is not received
- Inspection Procedure 2: The ignition switch (IG1) signal is not received
- Inspection Procedure 3: The key reminder switch signal is not received. < Vehicles without KOS >
- Inspection Procedure 4: The front door lock actuator (driver's side) signal is not received
- Inspection Procedure 5: The front door switch (driver's side) signal is not received
- Inspection Procedure 6: The front door switch (passenger's side) signal is not received
- Inspection Procedure 7: The rear door switch (RH) signal is not received
- Inspection Procedure 8: The rear door switch (LH) signal is not received
- Inspection Procedure 9: The liftgate lock actuator < vehicles without power liftgate > or liftgate latch < vehicles with power liftgate > signal is not received
- Inspection Procedure 10: The hazard warning light switch signal is not received
- Inspection Procedure 11: The column switch signal is not received
- Inspection Procedure 12: The stoplight switch signal is not received
- Inspection Procedure 13: The remote controlled mirror switch (fold switch) signal is not received
- Inspection Procedure 14: The ASC OFF switch signal is not received
- Inspection Procedure 15: The hood latch switch signal is not received
- Inspection Procedure 16: The LDW switch signal is not received
- Inspection Procedure 17: The Cruise control switch (ACC distance switch) signal is not received
- Inspection Procedure 18: The FCM switch signal is not received
- Inspection Procedure 19: The hazard indicator assembly (ECO mode switch) signal is not received
- Inspection Procedure 20: The transmission range switch signal is not received
- Connector: C-401
- Connector: C-402
- Connector: C-403
- Connector: C-404
- Connector: C-405
- Connector: C-410
- Connector: C-412
- Connector: C-413
- Connector: C-414
- Connector: C-415
- Connector: C-416
- Connector: C-417
- Connector: C-418
- Connector: C-419
- Connector: C-420
- Connector: C-421
- Connector: C-422
- On-Vehicle Service
- ETACS-Ecu