Engine Mechanical <2.0L Turbo> - Lancer

• General Information
• Engine Diagnosis
• Service Specifications
• Sealants
• Special Tools
• On-Vehicle Service
  • Drive Belt Tension Check
  • Auto-TENSIONER Check
    • Operation Check
    • Function Check
      • Notes
      • <When the vibration frequency is measured: Recommendation>
      • <When using a tension gauge>
  • Valve Clearance Check And Adjustment
  • Ignition Timing Check
  • Curb Idle Speed Check
  • Idle Mixture Check
  • Compression Pressure Check
  • Manifold Vacuum Check
  • Timing Chain Elongation Visual Check
• Crankshaft Pulley
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Drive Belt Removal
      • <<B>> Crankshaft Pulley Center Bolt/Crankshaft Pulley Washer/Crankshaft Pulley Removal
    • Installation Service Points
      • >>A<< Crankshaft Pulley/Crankshaft Pulley Washer/Crankshaft Pulley Center Bolt Installation
      • >>B<< Drive Belt Installation
• Camshaft
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Rocker Cover Assembly Removal
      • <<B>> Number 1 Cylinder Compression Top Dead Center Setting
      • <<C>> Camshaft And Camshaft Sprocket Assembly (Exhaust Side) Removal Preparatory Operation
      • <<D>> Front Camshaft Bearing Cap Removal
      • <<E>> Oil Feeding Camshaft Bearing Cap/Camshaft Bearing Cap/Thrust Camshaft Bearing Cap Removal
      • <<F>> Camshaft And Camshaft Sprocket Assembly (Exhaust Side) Removal
      • <<G>> Camshaft Sprocket Bolt/Camshaft Sprocket/Camshaft Removal
      • <<H>> Power Steering Oil Pump Assembly Removal
      • <<I>> Oil Feeder Control Valve Removal
    • Installation Service Points
      • >>A<< O-Ring/Oil Feeder Control Valve Installation
      • >>B<< Camshaft/Camshaft Sprocket/Camshaft Sprocket Bolt Installation
      • >>C<< Camshaft And Camshaft Sprocket Assembly (Intake Side) Installation
      • >>D<< Thrust Camshaft Bearing Cap/Camshaft Bearing Cap/Oil Feeding Camshaft Bearing Cap/Camshaft Bearing Installation
      • >>E<< Camshaft Bearing/Camshaft And Camshaft Sprocket Assembly (Exhaust Side) Installation
      • >>F<< Front Camshaft Bearing Cap Installation
      • >>G<< Rocker Cover Assembly Installation
• Valve Stem Seal
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Front Camshaft Bearing Cap Removal
      • <<B>> Oil Feeding Camshaft Bearing Cap/Camshaft Bearing Cap/Thrust Camshaft Bearing Cap Removal
      • <<C>> Valve Tappet Removal
      • <<D>> Valve Spring Retainer Lock Removal
      • <<E>> Valve Stem Seal Removal
    • Installation Service Points
      • >>A<< Valve Stem Seal Installation
      • >>B<< Valve Spring Installation
      • >>C<< Valve Spring Retainer Lock Installation
      • >>D<< Valve Tappet Installation
      • >>E<< Thrust Camshaft Bearing Cap/Camshaft Bearing Cap/Oil Feeding Camshaft Bearing Cap Installation
      • >>F<< Camshaft Bearing/Camshaft And Camshaft Sprocket Assembly (Exhaust Side) Installation
      • >>G<< Front Camshaft Bearing Cap Installation
• Oil Pan
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> A/C Compressor And Clutch Assembly Removal
      • <<B>> Engine Oil Pan Removal
    • Installation Service Points
      • >>A<< Engine Oil Pan Installation
      • >>B<< Engine Oil Pan Drain Plug Gasket Installation
      • >>C<< A/C Compressor And Clutch Assembly Installation
  • Inspection
• Crankshaft Oil Seal
  • Removal And Installation
    • Notes
    • Removal Service Point
      • <<A>> Flywheel Bolt Removal
    • Installation Service Points
      • >>A<< Crankshaft Rear Oil Seal Case Assembly Installation
      • >>B<< Flywheel/Flywheel Hub/Flywheel Bolt Installation
      • >>C<< Crankshaft Front Oil Seal Installation
• Cylinder Head Gasket
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Radiator Upper Hose/Radiator Lower Hose Disconnection
      • <<B>> Fuel High-Pressure Hose Disconnection
      • <<C>> Front Camshaft Bearing Cap Removal
      • <<D>> Oil Feeding Camshaft Bearing Cap/Camshaft Bearing Cap/Thrust Camshaft Bearing Cap Removal
      • <<E>> Cylinder Head Bolt/Cylinder Head Bolt Washer/Cylinder Head Bolt And Washer Assembly Removal
    • Installation Service Points
      • >>A<< Cylinder Head Gasket/Cylinder Head Assembly Installation
      • >>B<< Cylinder Head Bolt And Washer Assembly/Cylinder Head Bolt Washer/Cylinder Head Bolt Installation
      • >>C<< Camshaft Bearing/Camshaft And Camshaft Sprocket Assembly Installation
      • >>D<< Thrust Camshaft Bearing Cap/Camshaft Bearing Cap/Oil Feeding Camshaft Bearing Cap Installation
      • >>E<< Front Camshaft Bearing Cap Installation
      • >>F<< O-Ring Installation
      • >>G<< Fuel High-Pressure Hose Connection
      • >>H<< Radiator Lower Hose/Radiator Upper Hose Connection
• Timing Chain
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Power Steering Oil Pump Assembly Removal
      • <<B>> Engine And Transaxle Assembly Holding
      • <<C>> Crankshaft Pulley Removal
      • <<D>> Auto-TENSIONER Removal
      • <<E>> Timing Chain Case Assembly Removal
      • <<F>> Timing Chain TENSIONER Removal
    • Installation Service Points
      • >>A<< Timing Chain Installation
      • >>B<< Timing Chain TENSIONER Installation
      • >>C<< Crankshaft Front Oil Seal Installation
      • >>D<< Timing Chain Case Assembly Installation
      • >>E<< Water Pump Pulley Installation
• Engine Assembly
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Radiator Upper Hose/Radiator Lower Hose Disconnection
      • <<B>> A/C Compressor And Clutch Assembly Removal
      • <<C>> Engine Mounting Bracket/Engine Assembly Removal
    • Installation Service Points
      • >>A<< Engine Assembly/Engine Mounting Bracket Installation
      • >>B<< A/C Compressor And Clutch Assembly Installation
      • >>C<< Radiator Lower Hose/Radiator Upper Hose Connection