LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2021 >> Metris Van Cargo >> Repair and Diagnosis >> Body & Frame >> Windows >> Doors (1 Of 3) -- 447 Chassis >> Testing & Repair >> Disassembling And Assembling Front Door - AR72.10-S-0510E

Disassembling And Assembling Front Door - AR72.10-S-0510E

Model 447, 448 

G16488250Courtesy of MERCEDES-BENZ USA
G16488251Courtesy of MERCEDES-BENZ USA
G16488252Courtesy of MERCEDES-BENZ USA
WARNING Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. No parts of the body or limbs should be within the operating area when the components are moving. AS00.00-Z-0011-01A
Notice  Notes on carrying out repair work in the vehicle interior   AH68.00-D-0001-01KOS
DISASSEMBLINGASSEMBLING Disassemble/assemble     
1 Remove door trim on front door (1).   AR72.10-S-6575E 
2 Remove window of the front door.   AR72.10-S-1910E 
3 Remove outside door handle from front door.   AR72.10-S-2400E 
4 Remove front door lock.   AR72.10-S-4011E 
5 Remove door module.   AR72.10-S-0900E 
6 Remove outside mirror.   AR88.70-S-9000E
7.1 Remove trim element from front door. Model 447.8 with code VQ1 (AVANTGARDE)
Model 448.8
AR88.85-S-9741E
7.2 Remove outer sealing rail. Model 447 except code VQ1 (AVANTGARDE)
Model 448.7
AR72.10-S-1700E 
8 Remove seal for side window at front door.   AR72.10-S-1905E 
9 Remove the inner trim (4) from the window frame of the front door. Model 447.8
Model 448
AR72.10-S-6580E 
10 Remove the decorative foil from the window frame of the front door. If installed. AR72.10-S-1016E 
11 Remove the spacer (2).    
12 Remove seal (3). Model 447.7 with code ZQ9 (Tourer SELECT)
Model 447.8
Model 448
 
13 Remove seal (5).   AR72.10-S-1550E 
14 Remove the trim in the footwell on the driver's side. When disassembling front door on passenger side. AR68.30-S-4020E
15 Remove trim in front passenger side footwell. When disassembling front door on passenger side. AR68.30-S-4030E
16 Remove the signal acquisition and actuation module (SAM) control unit and place to one side. When disassembling front door on passenger side.
Model 447, 448 except code XM7 (MOPF II)
AR54.21-S-1257E
    Model 447, 448 with code XM7 (MOPF II) AR54.21-S-1257EH
17 Disconnect electrical connectors (6). IMPORTANT Number of electrical connectors (6) can vary depending on equipment installed.  
18 Remove the grommet (8) on the front door.    
19 Unscrew the screws (9) for the door holder (10) on the front door. TORQUE SPECIFICATION Bolt of door holder to door *BA72.10-Z-1002-01KOG 
20 Loosen the clamp screws (11) and remove the front door. NOTES Carefully handle front door. Otherwise paint damage can occur.
IMPORTANT Aid of helper required.
IMPORTANT Guide electrical wiring harness (7) through grommet (8) on A-pillar.
TORQUE SPECIFICATION Bolt, hinge on door
*BA72.10-Z-1004-01KOG 
21 Unscrew the screws (12) and remove the hinges (13). IMPORTANTAssembly:  Do not tighten the screws (12) until you have adjusted the front door.  
22 Remove the electrical wiring harness (7) from the front door.    
23 Remove the guide (14).    
24 Assemble in the reverse order.    
  Adjust     
25 Adjust front door.   AR72.10-S-0550E 
FRONT DOOR

Number Designation Model 447, 448
BA72.10-Z-1002-01KOG Bolt of door holder to door Nm 14
FRONT DOOR

Number Designation Model 447, 448
BA72.10-Z-1004-01KOG Bolt, hinge on door Nm 25