Section 53 (Crank Assembly -- 118 Chassis)
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
- General Information
- General Notes: Passenger Cars: Crank Assembly - AH03.00-Z-9999AZ
- Notes On Assessing Wear On Connecting Rod Bearings And Connecting Rod Journals - AH03.10-P-0001-03MM
- Notes On The Assessment Of Pistons And Piston Rings - AH03.10-P-0001-04MM
- Information On Assessing Wear Of Main Bearings And Main Bearing Journals - AH03.20-P-1000-02MM
- Interference Fit Of Crankshaft Bearing Cap - AH03.20-P-4351-02MM
- Safety Precautions
- Testing & Repair
- Check Connecting Rod Bolts
- Tighten Connecting Rod Bolts
- Install And Gauge Connecting Rod Bearings - AR03.10-P-6111-06MR
- Remove/Install Piston
- Measure Vertical Clearance Of Piston Rings
- Measure Piston Ring End Gap
- Remove/Install Piston Rings
- Place Balance Shafts In Basic Position - AR03.20-P-1105-02MFC
- Remove/Install Balance Shaft Housing - AR03.20-P-1105MFC
- Install Front Radial Shaft Sealing Ring - AR03.20-P-3002-01MFC
- Install Rear Radial Shaft Sealing Ring - AR03.20-P-3003-01MFC
- Remove/Install Front Radial Crankshaft Sealing Ring - AR03.20-P-3004MFC
- Remove/Install Rear Crankshaft Radial Sealing Ring
- Remove/Install Guide Bearing - AR03.20-P-4200MFG
- Determine Crankshaft Bearing Axial Play - AR03.20-P-4291-03MR
- Tightening Procedure For Crankshaft Bearing Caps - AR03.20-P-4351-02MR
- Remove/Install Crankshaft
- Assign Crankshaft Bearing Shells
- Check Crankshaft In Removed State - AR03.20-P-4463-01MR
- Remove/Install Retaining Lock For Crankshaft On Belt Side - AR03.30-P-0004MFG
- Remove/Install Crankshaft Belt Pulley/Vibration Damper
- Remove/Install Retaining Lock For Crankshaft/Ring Gear
- Remove/Install Flywheel/Drive Plate
- Test & Adjustment Values
- Test And Adjustment Values: Passenger Cars: Crank Assembly - BE03.00-Z-9999AZ
- Test Specifications For Pistons - BE03.10-P-1000-02L
- Test Specifications For Connecting Rod Bolts - BE03.10-P-1000-03A
- Check Values For Piston Rings - BE03.10-P-1000-05L
- Test Specifications For Crankshaft
- Check Values For Crankshaft Main Bearing Shells - BE03.20-P-1000-03L
- Test Specifications For Crankshaft Bearing Clearance - BE03.20-P-1000-04H
- Lanchester Balancer - BE03.20-P-1000-05B
- Thrust Plate Test Specifications - BE03.20-P-1000-08A
- Torque Specifications
- Special Tools
- 000 589 04 14 00 Tensioning Strap - WS03.00-P-0001C
- 000 589 20 21 00 Hardness Tester - WS03.00-P-0002C
- 000 589 51 37 00 Pliers - WS03.00-P-0005C
- 001 589 65 09 00 Socket Wrench Bit - WS03.00-P-0006B
- 001 589 32 21 00 Dial Indicator - WS03.00-P-0007B
- 270 589 00 15 00 Drift - WS03.00-P-0061B
- 270 589 00 68 00 Adapter - WS03.00-P-0062B
- 246 589 02 43 00 Insertion Device - WS03.00-P-0067B
- 654 589 00 40 00 Counterholder - WS03.00-P-0079B
- 654 589 00 43 00 Insertion Device - WS03.00-P-0082B
- 270 589 03 40 00 Retaining Lock - WS03.00-P-0105A
- 651 589 01 61 00 Insertion Tool - WS03.00-P-0113B
- 270 589 00 33 02 Spindle - WS03.00-P-0125-02B
- 270 589 00 33 00 Puller - WS03.00-P-0125B
- 001 589 93 21 00 Dial Indicator - WS03.00-P-0169B
- 139 589 05 40 00 Adapter - WS03.00-P-0176B
- 139 589 00 43 00 Removal And Installation Tool - WS03.00-P-0177B
- 139 589 01 43 00 Removal And Installation Tool - WS03.00-P-0263B