Remove/Install Retaining Lock For Crankshaft/Ring Gear - AR03.30-P-5000MFC
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Engine 260 in model 118, 177, 247
Shown on model 177 without code M016 (performance-enhanced engine)
| Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | AS00.00-Z-0002-01A | |
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. |
AS00.00-Z-0017-01A | |
| Notice | Notes on avoiding damage through contamination and foreign objects | AH00.00-P-5000-01A | |
| Install/remove | |||
| 1 | Remove air filter housing. | AR09.10-P-1150MFC | |
| 2 | Remove battery carrier. | AR54.10-P-0028MFA | |
| 3.1 | Remove starter. | If retaining lock should be installed in installed transmission. Engine 260 in model 118, 177, 247 except code B01 (48V technology) |
AR15.30-P-7100MFC |
| 3.2 | Remove cover over starter opening. | Engine 260 in model 118, 177, 247 with code B01 (48V technology) If retaining lock should be installed in installed transmission. |
*BA15.30-P-1003-01J |
| 3.3 | Remove transmission. | If retaining lock should be installed in removed transmission. Engine 260 in model 118, 177, 247 with transmission 724.1 |
AR01.10-P-2401MFJ |
| Engine 260 in model 118, 177, 247 with transmission 724.0 | AR01.10-P-2401MFC | ||
| 4.1 | Rotate the engine at the center bolt of the crankshaft in the direction of engine rotation and check the toothing of the starter ring gear (1) for wear or damage. | With installed transmission. | |
| Fig 3 | |||
| If there are problems: ↓ Replace drive plate. Engine 260 in model 118, 177, 247 with transmission 724.0 |
AR03.30-P-8001MFC | ||
| Engine 260 in model 118, 177, 247 with transmission 724.1 | AR03.30-P-8001MFI | ||
| 4.2 | Check the starter ring gear (1) for wear or damage. | With removed transmission. If there are problems: ↓ Replace drive plate. Engine 260 in model 118, 177, 247 with transmission 724.0 |
AR03.30-P-8001MFC |
| Engine 260 in model 118, 177, 247 with transmission 724.1 | AR03.30-P-8001MFI | ||
| 5.1 | Insert retaining lock (01) in starter opening until it engages with the starter ring gear (1). | With installed transmission. |
Fig 2 |
| 5.2 | Install the retaining lock (02) on the crankcase. | With removed transmission. |
Fig 1 |
| 6 | Removal in the reverse order. |
STARTER
| Number | Designation | Engine 260 | |
|---|---|---|---|
| BA15.30-P-1003-01J | Bolt, starter to crankcase/transmission | Nm | 38 |