Section 93 (Engine Mechanical - 2.8L Or 3.0L - Repair Instructions - Off Vehicle (2 Of 5))
WARNING: This page is about a different car, the 2010 Cadillac SRX. However, it is still accessible from the selected car via links, so may be relevant.
- Camshaft Position Actuator Removal - Left Side Intake
- Camshaft Position Actuator Removal - Right Side Exhaust
- Camshaft Position Actuator Removal - Right Side Intake
- Fuel Pump Removal (LF1 or LFW)
- Camshaft Removal - Left Side
- Fuel Rail Removal (LAU or LBW)
- Fuel Rail Removal (LF1)
- Valve Rocker Arm Removal - Left Side
- Valve Lifter Removal - Left Side
- Cylinder Head Removal - Left Side (LF1 or LFW)
- Cylinder Head Removal - Left Side (LAU or LBW)
- Camshaft Removal - Right Side
- Valve Rocker Arm Removal - Right Side
- Valve Lifter Removal - Right Side
- Cylinder Head Removal - Right Side (LF1 or LFW)
- Cylinder Head Removal - Right Side (LAU or LBW)
- Oil Pan Removal
- Oil Pump Removal
- Crankshaft Rear Oil Seal and Housing Removal
- Piston, Connecting Rod, and Bearing Removal
- Piston Oil Nozzle Removal
- Crankshaft and Bearing Removal
- Engine Block Disassemble (LF1)
- Engine Block Disassemble (LAU or LBW)
- Exhaust Manifold Cleaning and Inspection - Left Side
- Exhaust Manifold Cleaning and Inspection - Right Side
- Engine Block Cleaning and Inspection
- Crankshaft and Bearing Cleaning and Inspection
- Crankshaft Balancer Cleaning and Inspection
- Engine Flywheel Cleaning and Inspection
- Piston and Connecting Rod Disassemble
- Piston, Connecting Rod, and Bearing Cleaning and Inspection
- Piston and Connecting Rod Assemble
- Cylinder Head Disassemble (LF1 or LFW)
- Cylinder Head Disassemble (LAU or LBW)
- Cylinder Head Cleaning and Inspection
- Valve Spring Inspection and Measurement
- Valve and Seat Grinding
- Valve Cleaning Procedure
- Valve Visual Inspection Procedure
- Valve Measurement and Reconditioning Overview
- Valve Seat Width Measurement Procedure
- Valve Seat Roundness Measurement Procedure
- Valve Margin Measurement Procedure
- Valve-to-Seat Concentricity Measurement Procedure
- Valve and Seat Reconditioning Procedure
- Valve Stem Height Measurement Procedure
- Fuel Rail and Injectors Cleaning and Inspection (LF1 or LFW)
- Fuel Rail and Injectors Cleaning and Inspection (LAU or LBW)
- Cylinder Head Assemble (LF1 or LFW)
- Cylinder Head Assemble (LAU or LBW)
- Camshaft Cleaning and Inspection
- Valve Lifter Cleaning and Inspection
- Valve Rocker Arm Cleaning and Inspection
- Camshaft Timing Drive Components Cleaning and Inspection
- Cleaning Procedure
- Visual Inspection
- Camshaft Thrust Washers
- Camshaft Position Actuators
- Camshaft Position Actuator Oil Control Valves
- Left Intermediate Sprocket with Primary and Secondary Inverted Tooth (IT) Chain
- Right Intermediate Sprocket with Primary and Secondary Inverted Tooth (IT) Chain
- Crankshaft Sprocket with Primary Inverted Tooth (IT) Chain
- Secondary Timing Chains with Inverted Tooth (IT) Chain
- Primary Timing Chain with Inverted Tooth (IT) Chain
- Primary Timing Chain Upper Guide
- Primary Timing Chain Lower Guide
- Left Secondary Timing Chain Guide
- Right Secondary Timing Chain Guide
- Left Secondary Timing Chain Shoe
- Right Secondary Timing Chain Shoe
- Primary Timing Chain Tensioner
- Left Secondary Timing Chain Tensioner
- Right Secondary Timing Chain Tensioner
- Oil Pump Disassemble
- Oil Pump Cleaning and Inspection
- Oil Filter Adapter Disassemble (LF1)
- Oil Filter Adapter Disassemble (LAU or LBW)