Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different variant/trim than selected.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods
| Module | DTC | Description | Action |
|---|---|---|---|
| TCM | P0602:00 | Powertrain Control Module Programming Error: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0604:00 | Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0605:00 | Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0606:00 | Control Module Processor: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0607:00 | Control Module Performance: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P060A:00 | Internal Control Module Monitoring Processor Performance: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P060B:00 | Internal Control Module A/D Processing Performance: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P060C:00 | Internal Control Module Main Processor Performance: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0610:00 | Control Module Vehicle Options Error: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0613:00 | TCM Processor: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0642:00 | Sensor Reference Voltage 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0643:00 | Sensor Reference Voltage 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P0652:00 | Sensor Reference Voltage 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0653:00 | Sensor Reference Voltage 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test E |
| TCM | P0657:00 | Actuator Supply Voltage 'A' Circuit/Open: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0658:00 | Actuator Supply Voltage 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0659:00 | Actuator Supply Voltage 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P0698:00 | Sensor Reference Voltage 'C' Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P0699:00 | Sensor Reference Voltage 'C' Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06A4:00 | Sensor Reference Voltage 'D' Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P06A5:00 | Sensor Reference Voltage 'D' Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P06B0:00 | Sensor Power Supply 'A' Circuit/Open: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06B1:00 | Sensor Power Supply 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06B2:00 | Sensor Power Supply 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06B3:00 | Sensor Power Supply 'B' Circuit/Open: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06B4:00 | Sensor Power Supply 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06B5:00 | Sensor Power Supply 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| TCM | P06B8:00 | Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P06D3:00 | Sensor Reference Voltage 'E' Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P06D4:00 | Sensor Reference Voltage 'E' Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P06E4:00 | Control Module Wake-up Circuit Performance: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0711:00 | Transmission Fluid Temperature Sensor 'A' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0712:00 | Transmission Fluid Temperature Sensor 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0713:00 | Transmission Fluid Temperature Sensor 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P0716:00 | Input/Turbine Shaft Speed Sensor 'A' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P071D:00 | Transmission Mode Switch 'B' Circuit: No Sub Type Information | GO to Pinpoint Test Y |
| TCM | P071E:00 | Transmission Mode Switch 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test Y |
| TCM | P071F:00 | Transmission Mode Switch 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test Y |
| TCM | P0721:00 | Output Shaft Speed Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P0729:00 | Gear 6 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P072B:00 | Stuck in Reverse: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P072C:00 | Stuck in Gear 1: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P072D:00 | Stuck in Gear 2: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P072E:00 | Stuck in Gear 3: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P072F:00 | Stuck in Gear 4: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0731:00 | Gear 1 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0732:00 | Gear 2 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0733:00 | Gear 3 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0734:00 | Gear 4 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0735:00 | Gear 5 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0736:00 | Reverse Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P073A:00 | Stuck in Gear 5: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P073B:00 | Stuck in Gear 6: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P073C:00 | Stuck in Gear 7: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P073E:00 | Unable to Engage Reverse: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P073F:00 | Unable to Engage Gear 1: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0746:00 | Pressure Control Solenoid 'A' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P0747:00 | Pressure Control Solenoid 'A' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P074A:00 | Unable to Engage Gear 2: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P074B:00 | Unable to Engage Gear 3: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P074C:00 | Unable to Engage Gear 4: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P074D:00 | Unable to Engage Gear 5: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P074E:00 | Unable to Engage Gear 6: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P074F:00 | Unable to Engage Gear 7: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P076F:00 | Gear 7 Incorrect Ratio: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P0776:00 | Pressure Control Solenoid 'B' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P0777:00 | Pressure Control Solenoid 'B' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P077C:00 | Output Shaft Speed Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P077D:00 | Output Shaft Speed Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P0792:00 | Intermediate Shaft Speed Sensor 'A' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P0796:00 | Pressure Control Solenoid 'C' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P0797:00 | Pressure Control Solenoid 'C' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P07B3:00 | Transmission Park Position Sensor/Switch 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07B4:00 | Transmission Park Position Sensor/Switch 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07B5:00 | Transmission Park Position Sensor/Switch 'A' Circuit Performance/Low: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07B7:00 | Transmission Park Position Sensor/Switch 'A' Circuit Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07B9:00 | Transmission Park Position Sensor/Switch 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07BA:00 | Transmission Park Position Sensor/Switch 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07BD:00 | Transmission Park Position Sensor/Switch 'B' Circuit Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test I |
| TCM | P07BF:00 | Input/Turbine Shaft Speed Sensor 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P07C0:00 | Input/Turbine Shaft Speed Sensor 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P07C5:00 | Intermediate Shaft Speed Sensor 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P07C6:00 | Intermediate Shaft Speed Sensor 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P07C7:00 | Intermediate Shaft Speed Sensor 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P07C8:00 | Intermediate Shaft Speed Sensor 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P07E4:00 | Unable to Engage Park: No Sub Type Information | GO to Pinpoint Test X |
| TCM | P07E6:00 | Stuck in Park: No Sub Type Information | GO to Pinpoint Test X |
| TCM | P0841:00 | Transmission Fluid Pressure Sensor/Switch 'A' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0842:00 | Transmission Fluid Pressure Sensor/Switch 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0843:00 | Transmission Fluid Pressure Sensor/Switch 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0844:00 | Transmission Fluid Pressure Sensor/Switch 'A' Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0846:00 | Transmission Fluid Pressure Sensor/Switch 'B' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0847:00 | Transmission Fluid Pressure Sensor/Switch 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0848:00 | Transmission Fluid Pressure Sensor/Switch 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0849:00 | Transmission Fluid Pressure Sensor/Switch 'B' Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0867:00 | Transmission Fluid Pressure: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P0868:00 | Transmission Fluid Pressure Low: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P0869:00 | Transmission Fluid Pressure High: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P0871:00 | Transmission Fluid Pressure Sensor/Switch 'C' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0872:00 | Transmission Fluid Pressure Sensor/Switch 'C' Circuit Low: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0873:00 | Transmission Fluid Pressure Sensor/Switch 'C' Circuit High: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0874:00 | Transmission Fluid Pressure Sensor/Switch 'C' Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P0882:00 | TCM Power Input Signal Low: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P0883:00 | TCM Power Input Signal High: No Sub Type Information | GO to Pinpoint Test A |
| TCM | P08C4:00 | Pressure Control Solenoid 'M' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P08C5:00 | Pressure Control Solenoid 'M' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P08C8:00 | Pressure Control Solenoid 'M' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P08CA:00 | Pressure Control Solenoid 'M' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P08CB:00 | Pressure Control Solenoid 'M' Control Circuit High: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P0960:00 | Pressure Control Solenoid 'A' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0962:00 | Pressure Control Solenoid 'A' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0963:00 | Pressure Control Solenoid 'A' Control Circuit High: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0964:00 | Pressure Control Solenoid 'B' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P0966:00 | Pressure Control Solenoid 'B' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P0967:00 | Pressure Control Solenoid 'B' Control Circuit High: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P0968:00 | Pressure Control Solenoid 'C' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0970:00 | Pressure Control Solenoid 'C' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P0971:00 | Pressure Control Solenoid 'C' Control Circuit High: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P1188:00 | Calibration Memory: No Sub Type Information | GO to Pinpoint Test B |
| TCM | P1601:00 | ECM/TCM Serial Communication Error: No Sub Type Information | GO to Pinpoint Test Q |
| TCM | P163E:00 | Transmission Control Module Programming Error: No Sub Type Information | GO to Pinpoint Test Z |
| TCM | P163F:00 | Transmission ID Block Corrupted, Not Programmed: No Sub Type Information | GO to Pinpoint Test Z |
| TCM | P175C:00 | Transmission Fluid Pressure Sensor/Switch 'A' Circuit Out Of Range High: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P175D:00 | Transmission Fluid Pressure Sensor/Switch 'B' Circuit Out Of Range High: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P175E:00 | Transmission Fluid Pressure Sensor/Switch 'C' Circuit Out Of Range High: No Sub Type Information | GO to Pinpoint Test F |
| TCM | P175F:00 | Transmission Fluid Pressure Relief Valve Stuck: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P178A:00 | Shift Fork Selection Mechanism Stuck On: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P178B:00 | Shift Fork Selection Mechanism Stuck Off: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P178C:00 | Shift Fork Selection Valve Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P178D:00 | Shift Fork Selection Valve Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2669:00 | Actuator Supply Voltage 'B' Circuit/Open: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2670:00 | Actuator Supply Voltage 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2671:00 | Actuator Supply Voltage 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2684:00 | Actuator Supply Voltage 'C' Circuit/Open: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2685:00 | Actuator Supply Voltage 'C' Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2686:00 | Actuator Supply Voltage 'C' Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P26E7:00 | Actuator Supply Voltage 'D' Circuit/Open: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P26E8:00 | Actuator Supply Voltage 'D' Circuit Low: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P26E9:00 | Actuator Supply Voltage 'D' Circuit High: No Sub Type Information | GO to Pinpoint Test D |
| TCM | P2714:00 | Pressure Control Solenoid 'D' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2715:00 | Pressure Control Solenoid 'D' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2718:00 | Pressure Control Solenoid 'D' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P2720:00 | Pressure Control Solenoid 'D' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P2721:00 | Pressure Control Solenoid 'D' Control Circuit High: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P2723:00 | Pressure Control Solenoid 'E' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2724:00 | Pressure Control Solenoid 'E' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2727:00 | Pressure Control Solenoid 'E' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test J |
| TCM | P2729:00 | Pressure Control Solenoid 'E' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test J |
| TCM | P2730:00 | Pressure Control Solenoid 'E' Control Circuit High: No Sub Type Information | GO to Pinpoint Test J |
| TCM | P2735:00 | Pressure Control Solenoid 'F' Intermittent: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2736:00 | Pressure Control Solenoid 'F' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P2738:00 | Pressure Control Solenoid 'F' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P2739:00 | Pressure Control Solenoid 'F' Control Circuit High: No Sub Type Information | GO to Pinpoint Test K |
| TCM | P2741:00 | Transmission Fluid Temperature Sensor 'B' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P2742:00 | Transmission Fluid Temperature Sensor 'B' Circuit Low: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P2743:00 | Transmission Fluid Temperature Sensor 'B' Circuit High: No Sub Type Information | GO to Pinpoint Test G |
| TCM | P2746:00 | Intermediate Shaft Speed Sensor 'B' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test O |
| TCM | P277E:00 | Clutch 'A' Unexpected Mechanical Gear Disengagement: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P277F:00 | Clutch 'B' Unexpected Mechanical Gear Disengagement: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P27B1:00 | Internal Control Module Transmission Range Select Performance: No Sub Type Information | GO to Pinpoint Test AA |
| TCM | P27B2:00 | Internal Control Module Transmission Range Control Performance: No Sub Type Information | GO to Pinpoint Test AA |
| TCM | P27B3:00 | Internal Control Module Transmission Gear Select Performance: No Sub Type Information | GO to Pinpoint Test AA |
| TCM | P27B9:00 | Pressure Control Solenoid 'N' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27BA:00 | Pressure Control Solenoid 'N' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27BD:00 | Pressure Control Solenoid 'N' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27BF:00 | Pressure Control Solenoid 'N' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27C0:00 | Pressure Control Solenoid 'N' Control Circuit High: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27C1:00 | Pressure Control Solenoid 'P' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27C2:00 | Pressure Control Solenoid 'P' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27C5:00 | Pressure Control Solenoid 'P' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27C7:00 | Pressure Control Solenoid 'P' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27C8:00 | Pressure Control Solenoid 'P' Control Circuit High: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27C9:00 | Pressure Control Solenoid 'R' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27CA:00 | Pressure Control Solenoid 'R' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27CD:00 | Pressure Control Solenoid 'R' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27CF:00 | Pressure Control Solenoid 'R' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27D0:00 | Pressure Control Solenoid 'R' Control Circuit High: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27D9:00 | Pressure Control Solenoid 'T' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27DA:00 | Pressure Control Solenoid 'T' Stuck On: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P27DD:00 | Pressure Control Solenoid 'T' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27DF:00 | Pressure Control Solenoid 'T' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P27E0:00 | Pressure Control Solenoid 'T' Control Circuit High: No Sub Type Information | GO to Pinpoint Test M |
| TCM | P2811:00 | Pressure Control Solenoid 'G' Intermittent: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2812:00 | Pressure Control Solenoid 'G' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P2814:00 | Pressure Control Solenoid 'G' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P2815:00 | Pressure Control Solenoid 'G' Control Circuit High: No Sub Type Information | GO to Pinpoint Test L |
| TCM | P2820:00 | Pressure Control Solenoid 'J' Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test X |
| TCM | P2821:00 | Pressure Control Solenoid 'J' Stuck On: No Sub Type Information | GO to Pinpoint Test X |
| TCM | P2824:00 | Pressure Control Solenoid 'J' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P2826:00 | Pressure Control Solenoid 'J' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P2827:00 | Pressure Control Solenoid 'J' Control Circuit High: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P2832:00 | Shift Fork 'A' Position Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2833:00 | Shift Fork 'A' Position Circuit Low: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2834:00 | Shift Fork 'A' Position Circuit High: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2835:00 | Shift Fork 'A' Position Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2837:00 | Shift Fork 'B' Position Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2838:00 | Shift Fork 'B' Position Circuit Low: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2839:00 | Shift Fork 'B' Position Circuit High: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P283A:00 | Shift Fork 'B' Position Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P283C:00 | Shift Fork 'C' Position Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P283D:00 | Shift Fork 'C' Position Circuit Low: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P283E:00 | Shift Fork 'C' Position Circuit High: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P283F:00 | Shift Fork 'C' Position Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2841:00 | Shift Fork 'D' Position Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2842:00 | Shift Fork 'D' Position Circuit Low: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2843:00 | Shift Fork 'D' Position Circuit High: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P2844:00 | Shift Fork 'D' Position Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test H |
| TCM | P284D:00 | Shift Fork 'A' Unrequested Movement: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P284E:00 | Shift Fork 'B' Unrequested Movement: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P284F:00 | Shift Fork 'C' Unrequested Movement: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P2850:00 | Shift Fork 'D' Unrequested Movement: No Sub Type Information | GO to Pinpoint Test V |
| TCM | P2853:00 | Clutch 'A' Pressure Discharge Performance: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2854:00 | Clutch 'B' Pressure Discharge Performance: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2855:00 | Clutch 'A' Pressure Charge Performance: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P2856:00 | Clutch 'B' Pressure Charge Performance: No Sub Type Information | GO to Pinpoint Test W |
| TCM | P287C:00 | Transmission Adaptive Values Not Learned: No Sub Type Information | GO to Pinpoint Test Z |
| TCM | P2887:00 | Park Lock/Pawl Actuator Circuit: No Sub Type Information | GO to Pinpoint Test X |
| TCM | P2888:00 | Park Lock/Pawl Actuator Circuit/Open: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P2889:00 | Park Lock/Pawl Actuator Circuit Low: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P288A:00 | Park Lock/Pawl Actuator Circuit High: No Sub Type Information | GO to Pinpoint Test N |
| TCM | P288B:00 | Park Lock/Pawl Actuator Circuit Performance: No Sub Type Information | GO to Pinpoint Test X |
| TCM | U0103:00 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test P |
| TCM | U0115:00 | Lost Communication With ECM/PCM 'B': No Sub Type Information | GO to Pinpoint Test Q |
| TCM | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information | GO to Pinpoint Test R |
| TCM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test S |
| TCM | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test T |
| TCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test B |